Unipolar plasma electrolytic oxidation: Waveform optimisation for corrosion resistance of commercially pure titanium

This study deals with the anodisation of titanium grade 2 in 0.5-M sulphuric acid using a pulsed signal in a unipolar regime. The electrical parameters investigated are voltage, frequency and duty cycle. The use of duty cycles with a high percentage of anodic polarisation (90%), combined with high frequencies (1000 Hz) and the higher voltage tested (220 V), favoured the establishment of a plasma regime involving strong dielectric discharges, allowing the growth of thicker oxides but with rough architecture. The corrosion resistance of the formed film has been characterised by potentiodynamic tests in 0.5-M NaBr for localised corrosion resistance and by immersion tests in 10% v/v sulphuric acid solution for a uniform corrosion assessment. Current–time curves, visual observations and electron microscope analysis (scanning electron microscopy, energy-dispersive X-ray spectroscopy) were the tools selected to provide a correlation between technological parameters and oxide growth mechanism. For localised and uniform corrosion, anodisation at 220 V with a high level of anodic polarisation (90%) and frequency (1000 Hz) was verified to be particularly advantageous.     

Systematic optimization of corrosion,bioactivity, and biocompatibility behaviors of calcium-phosphate plasma electrolytic oxidation (PEO) coatings on titanium substrates

To optimize the corrosion, bioactivity, and biocompatibility behaviors of plasma electrolytic oxidation (PEO) coatings on titanium substrates, the effects of five process variables including frequency, current density, duty cycle, treatment time, and electrolyte Ca/P ratio were evaluated. In our systematic study, a Taguchi design of experimental based on an L16 orthogonal array was used. For this, the coatings characteristics such as the surface roughness, wettability, rutile to anatase and Ca/P ratios, and corrosion polarization resistance were investigated. After determining the optimum process variables for each response, the apatite forming ability in SBF (bioactivity behavior) and MG63 cell attachment and flattening (biocompatibility behavior) for two groups of coatings were examined. The first group was optimized based on the maximum corrosion polarization resistance and the variables were set as the frequency of 2000 Hz, the current density of 5 A/dm², the duty cycle of 30%, the treatment time of 5 min, and the Ca/P ratio of 0.65 at. % in the electrolyte. For the second group, the maximum surface roughness, greatest Ca/P ratio, and highest wettability as well as the minimum rutile to anatase ratio in coatings, could be obtained when the variables were set as the frequency of 10 Hz, the current density of 12.5 A/dm², the duty cycle of 50%, the treatment time of 12.5 min, and the Ca/P ratio of 1.70 at. % in the electrolyte. The results showed that while both groups of coatings indicated a significant apatite forming ability and can serve as bioactive coatings, a proper attachment and flattening of cells and consequently, the favorable biocompatibility properties were seen only in the first group.     

超高压大容量铝电解电容器的研制

分析了大功率设备用超高压大容量铝电解电容器的特点,通过研制工作电解液、制订制作工艺及零部件设计方案,研制出的超高压大容量铝电解电容器具有损耗角正切小(tgδ为0.25)、承受纹波电流能力强(100 Hz,2.12～27.8 A)及寿命长的特点,耐久性达到85℃,5 000 h。     

提高超小型铝电解电容器生产一次合格率

恰当选择原材料、确保铆接工序质量、重视工作电解液的配比、严控各工序成品率是提高超小型铝电解电容器投入产出一次合格率的关键。以１０Ｖ－４７μＦ（４ｍｍ×７ｍｍ）产品为例，投入产出一次合格率达９４％以上。     

参数设计法在铝电解电容器设计中的应用探讨

论述了参数设计法在铝电解电容器设计开发阶段的应用。文中阐明了铝电解电容器的主要质量特性(损耗因子、电容量)及芯包外径的参数设计原理,并建立了归一化函数作为优选设计方案的判据。实例证明在铝电解电容器的设计过程中应用参数设计法以减小产品质量特性变异是有效的。     

硫酸/盐酸比例和Al~(3+)含量对铝箔隧道孔生长的影响

研究了硫酸/盐酸比例、温度和Al3+含量对高纯铝箔隧道孔生长的影响,发现随着硫酸浓度增加,温度对隧道孔极限长度和孔径的影响减小,在本文条件下隧道孔生长的临界温度最低可降低到35℃。在电解液中一定含量的Al3+可以避免铝箔表面形成大孔,从而改善隧道孔分布均匀性。     

大型预焙铝电解槽使用碳化硅砖与普通碳砖复合块的探讨

碳化硅砖和碳化硅砖与普通碳砖复合侧块，在上世纪末期我国铝电解槽上开始推广应用。使用后各厂家普遍发现碳化硅砖及碳化硅砖与普通碳块复合侧块均出现不同程度的断裂、上抬和脱落现象，该文对断裂、上抬和脱落原因进行了分析，并提出了改进措施。     

罐装食品用电镀锡板的耐蚀性及其试验方法

综述了影响罐装食品用电镀锡板耐蚀性能的因素及其试验方法。     

电解铜箔产业发展趋势

随着技术的进步,电解铜箔在厚度上迅速向薄、超薄方向发展,THE、RCC、CAC等特殊性能铜箔需求比例快速 增加,以锂离子电池为代表的新应用领域正在形成。     

CONSTITUTE AND PROPERTY OFα-Ti AFTER HYDRIDING TREATMENT

研究了氢化处理对退火α-Ti 板材的组织、结构及性能的影响。α-Ti 在室温出现两种结构的氢化物:有序的fctγ相(TiH)和fccδ相(TiH_2)。分析了用X 射线衍射只查觉到δ相的原因。氢化物的数量及形态影响除氢后基体的晶粒组织。控制氢含量可以改善拉伸性能及疲劳性能。