游梁式抽油机间歇供电装置的研制与应用

针对游梁抽油机电动机效率低和井场窃电问题,研制了具有节电和防井场窃电功能的游梁抽油机调压+间歇供电装置。该装置通过控制可控硅的导通角实现在电动机做功期调压供电,在电动机发电期不供电。分析了间歇供电对电动机、抽油机和电网的影响;根据现场实测数据分析了该装置的节电效果及现场应用情况。该装置节电效果显著,能防止井场窃电,可用于对游梁抽油机电动机的长期驱动。     

摩擦换向抽油机悬点运动分析计算

摩擦换向抽油机采用开关磁阻电动机或变频调速电动机,其特点是可以频繁双向旋转,带动摩擦轮正反转,实现光杆的上行下行。该抽油机运动特点与游梁式抽油机运动特点有较大区别,文章分析了摩擦换向抽油机的运动特点,给出了该机悬点位移、速度、加速度的计算方法。     

游梁式抽油机二次平衡分析

为解决游梁式抽油机能耗大、效率低的问题，设计了二次平衡装置。这种装置通过是挂在抽油机后端的平衡重的平衡作用，降低一次平衡曲柄轴净扭矩的两个峰值，达到减少能耗提高效率的目的。对抽油机的二次平衡作了较详尽的理论分析，给出了实行二次平衡后曲柄轴净扭矩的计算公式和安装二次平衡装置前后曲柄轴净扭矩曲线图。在大庆油田两口井上进行的现场试验结果表明，安装二次平衡装置后，两口井年节约电费分别为0.25万元和1．17万元，经济效益明显。     

直线式电机在有杆抽油设备中的应用

通过对游梁式抽油机的效率、启动特性与直线式电机驱动的有杆抽油机特性的对比，论述了直线抽油机的优越性及应用前景。     

压力计探测液面法探讨

针对油田地质特征复杂，易结蜡，测试中易出现假液面等情况，为准确快速测得液面资料，提出压力计测试液面法。该方法可作为回声仪测液面方法的有效补充。     

BYJ型防喷脱接器的设计与应用

本文介绍了BYJ型防喷脱接器的结构和工作原理。它既有抽油杆与大泵活塞脱接功能,又能实现不压井作业施工,是大型抽油泵理想的配套工具。现场应用表明,该防喷脱接器对接成功率较高,并实现了大泵井不压井施工。     

积极开展泵站技术改造

为探索山丘地区中小型泵站技术改造的经验，选定南康县四个小型泵站作为泵站改造的试点站，进行现场测试，根据测试成果，分析各站存在的问题及效率偏低的原因，并拟定各站技术改造的措施，经实施后取得了较好的效果，本文就南康县泵站改造的实际效果阐明泵站改造的必要性及其改造过程中值得注意的问题。     

Analysis and Optimization Laminar Viscous Flow Through a Channel

Optimizing of laminar viscous flow through a pipe by two dimensionless values is investigated analytically. Dimensionless entropy generation and pumping power to heat transfer rate ratio are used as basis for constant viscous and the temperature dependence on the viscosity. For this matter we calculate entropy generation and pumping power for a fully developed in a pipe subjected to constant wall temperature for either constant viscosity and the variable viscosity. The variation entropy generation increase along the pipe length for viscous fluid is drawn, either the variation summation dimensionless entropy generation and the pumping power to heat transfer rate ratio are varying the fluid inlet temperature for fixed pipe length and are varying pipe length for fixed fluid inlet temperature are drawn. For low heat transfer conditions the entropy generation due to viscosity friction becomes dominant and the dependence of viscosity with the temperature becomes essentially important to be considered.     

An analytical model for charge pumping below strong inversion and accumulation

A compact analytical model for charge pumping (CP) is derived. It accounts for emission during the high and low gate bias levels and assumes instantaneous transition edges. This model, which does not apply on the top of the CP curves when using large gate voltage swings, where emission fully proceeds during the transitions edges of the gate signal, applies on all the other regions provided that the transition times of the gate signal are much shorter than the times at steady state biases. Therefore it holds at large bias swings on both edges of Elliot curves and at small bias swings on the whole Elliot curves provided that the interface traps are completely filled [1]. It is compared with the analytical model proposed by Wachnik and Lowney [2] in which emission is not accounted for at all. This model, which holds at Elliot curve maxima when small voltage swings are used, has been shown to be extremely useful for studying interface trap properties [1, 2, 3 and 4]. The CP model proposed primarily, that of Brugler and Jespers [5], is used as a reference. The model derived in this article very satisfactorily fits the experimental curves in the regions of large CP current where it holds. Discrepancies at low current levels are due to the well-known contribution of the transistor source and drain regions or could be due to edge effects. Comparing the different models and the experimental curves allows to evaluate emission and capture during different regions of the gate bias period. The three regions of CP response, depending on the gate voltage swing and involving or not emission and the full filling of the interface traps, are also evidenced.