On the basis of generalization of the results of investigation of the operation of rodlike elements of composite materials, we make a conclusion that the influence of various factors on the deformability of these elements is studied incompletely. The comparison of the stress-strain states for different models of concrete and reinforced-concrete elements makes it possible to describe the effect of longitudinal reinforcement (coefficient of reinforcement, strength and deformation characteristics) on the critical level of strains in the cross section. According to the results of our investigations, we give recommendations concerning the evaluation of the critical value of the coefficient of reinforcement above which one may observe the effect of reinforcement on the deformability of the analyzed sections. It is shown that the compression strength of the brittle base of the composite with inhomogeneous structure decreases as a result of the fracture processes. It is also demonstrated that the existing procedure used for the evaluation of the indicated decrease in strength requires significant improvement. The problem of evaluation of the ultimate value of the coefficient of reinforcement is also analyzed. 相似文献
BaMgAl10O17∶Eu2 (BAM) was prepared in the microemulsion system and its phase behavior was studied. There exists a small region in the reverse microemulsion system where the dispersed particles are of spherical form. In this way, BAM blue phosphor with good dispersion can be synthesized. The microemulsion phase diagrams of the pseudo-ternary system (Triton X-100/cosurfactant-oil-BAM brine) were first established intuitively by the dilution method. The microstructure of microemulsions was determined through eyeballing, conductance technique, and polar optical microscopy. Its phase behavior is affected by various factors, such as temperature (room temperature, 30, 40 ℃), oil, surfactants, and cosurfactants in microemulsions. According to the phase diagrams, the microemulsion system of Triton X-100/1-hexanol-hexane-BAM brine was chosen to prepare the precursor. The BAM phosphor can be obtained via sintering the precursor at a comparatively low temperature. The phosphors were characterized by XRD and vacuum ultraviolet (VUV) spectra. 相似文献
It is an outstanding open problem of computational geometry to prove a near-quadratic upper bound on the number of combinatorial changes in the Voronoi diagram of points moving at a common constant speed along linear trajectories in the plane. In this note we observe that this quantity is Θ(n2) if the points start their movement from a common line. 相似文献
Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection tp/tp(red), where tp is the experimental measured time for the peak stress and tp(red) is the newly defined reduced time. The softening ratio X and time t0.05R for start of static recrystallization were established.
The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10−2 to 1 s−1.
In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t0.05R, t0.5R, t0.95R and t0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained. 相似文献
In this study a thermodynamic model for the phase behavior of aqueous salt+polymer solutions is developed. The model is based on the solution theory of Hill, which included scaling laws for the polymer molecular mass dependence and Pitzer–Debye–Hückel theory. This model was tested for systems composed of two different molecular mass of polyethylene glycols (PEG) and five different inorganic salts. All the model parameters were determined from independent measurements. The agreement between the experimental and predicted phase diagrams by this model is good. 相似文献
The general relationship between binary phase diagrams and the thermodynamic properties was system-atically derived without any assumption.A procedure was presented to estimate the thermodynamic proper-ties from the binary phase diagrams. 相似文献