Utilization of pyrolytic oil and hydrogen enriched syngas from single feedstock (delonix regia) through pyrolysis process and its influence on performance and emission characteristics in CI engine

The main objective of the present investigation is to conduct the performance, combustion and emission analysis of CI engine operated using hydrogen enriched syngas (pyrolytic gas) and biodiesel (pyrolytic oil) as dual fuel mode condition. Both the pyrolytic oil and syngas is obtained from single feedstock delonix regia fruit pod through pyrolysis process and then pyrolytic oil is converted into biodiesel through esterification. Initially biomass is subjected to thermal degradation at various pyrolysis temperature ranges like 350–600 °C. During the pyrolysis process syngas, pyrolytic oil and char are produced. The syngas is directly used in the CI engine and pyrolytic oil is converted into biodiesel and then used in the CI engine. The pyrolytic oil and syngas is subjected to FTIR and GC/TCD analysis respectively. The syngas analysis confirms the presence of various gases like H₂, CH₄, CO₂, CO and C₂H₄ in different proportions. The various proportions of the syngas is mainly depending upon the reactor temperature and moisture content in the biomass. The syngas composition varies with increase in the temperature and at 400 °C, higher amount of hydrogen is present and its composition are H₂ 28.2%, CO is 21.9%, CH₄ is 39.1% and other gases in smaller amounts. The biodiesel of B20 and syngas of 8lpm produced from the same feedstock are considered as test sample fuels in the CI engine under dual fuel mode operation to study the performance and emission characteristics. The study reveals that BTE has slight increase than diesel of 1.5% at maximum load. On the another hand emission like CO, HC and smoke are reduced by 15%,25% and 32% respectively at full load condition, whereas NO_x emission is increased at all loads in the range of 10–15%. Therefore B20+syngas of 8lpm can be used as an alternative fuel in CI engine without any modification and major products from pyrolysis process with waste biomass is fully used as fuel in the CI engine.     

Structure-sensitive semantic matching for aggregate question answering over knowledge base

Aggregate question answering essentially returns answers for given questions by obtaining query graphs with unique dependencies between values and corresponding objects. Word order dependency, as the key to uniquely identify dependency of the query graph, reflects the dependencies between the words in the question. However, due to the semantic gap caused by the expression difference between questions encoded with word vectors and query graphs represented with logical formal elements, it is not trivial to match the correct query graph for the question. Most existing approaches design more expressive query graphs for complex questions and rank them just by directly calculating their similarities, ignoring the semantic gap between them. In this paper, we propose a novel Structure-sensitive Semantic Matching(SSM) approach that learns aligned representations of dependencies in questions and query graphs to eliminate their gap. First, we propose a cross-structure matching module to bridge the gap between two modalities(i.e., textual question and query graph). Then, we propose an entropy-based gated AQG filter to remove the structural noise caused by the uncertainty of dependencies. Finally, we present a two-channel query graph representation that fuses the semantics of abstract structure and grounding content of the query graph explicitly. Experimental results show that SSM could learn aligned representations of questions and query graphs to eliminate the gaps between their dependencies, and improves up to 12% (F1 score) on aggregation questions of two benchmark datasets.     

Categorical observers for metamerism

A method is proposed to generate categorical colour observer functions (individual colour matching functions) for any field size based on the CIE 2006 system of physiological observer functions. The method combines proposed categorical observer techniques of Sarkar et al with a physiologically-based individual observer model of Asano et al and a clustering technique to produce the optimal set of categorical observers. The number of required categorical observers varies depending on an application with as many as 50 required to predict individual observers' matches when a laser projector is viewed. However, 10 categorical observers are sufficient to represent colour-normal populations for personalized colour imaging. The proposed and recommended categorical observers represent a robust and inclusive technique to examine and quantify observer metamerism in any application of colorimetry.     

Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

Annual and regional variations of aflatoxin B1 levels seen in grains and feed coming from Croatian dairy farms over a 5-year period

The aim of the study was to investigate annual and regional differences in the level of aflatoxin B₁ (AFB₁) in grains and dairy cattle feed. Maize (n = 972), wheat (n = 201), barley (n = 147), oat (n = 136), grain mixtures (n = 168), and dairy cattle feed (n = 325) were sampled from 2009 to 2013 on different farms and in different farm factories situated in four Croatian regions. The samples were analysed for AFB₁ using the validated ELISA immunoassay. AFB₁ was determined in 16.4% of all investigated samples, among which maize was proven to be the most contaminated, with 21.7% of the samples recovered during 2013 harbouring AFB₁ in concentrations over the permissible ones. Levels higher than permitted were observed in 17.9% and 12.3% of grain mixtures and dairy cattle feed, respectively, whereas concentrations of AFB₁ determined in other crops throughout the investigated period met the stipulated requirements. The results revealed the AFB₁ occurrence to be significantly (p < 0.05) dependent on the cultivation region, with the highest levels generally found in maize harvested in 2013 and consequently in grain mixtures and cattle feed that can most likely be associated with climatic conditions as the most critical factor for mould formation, and thus also AFB₁ production.     

Simplified anode architecture for PEMFC systems based on alternative fuel feeding: Experimental characterization and optimization for automotive applications

The need to reduce PEMFC systems cost as well as to increase their durability is crucial for their integration in various applications and especially for transport applications. A new simplified architecture of the anode circuit called Alternating Fuel Feeding (AFF) offers to reduce the development costs. Requiring a new stack concept, it combines the simplicity of Dead-End Anode (DEA) with the operation advantages of the hydrogen recirculation. The three architectures (DEA, recirculation and AFF) are compared in terms of performance on a 5-kW test bench in automotive conditions, through a sensitivity analysis. A gain of 17% on the system efficiency is observed when switching from DEA to AFF. Moreover, similar performances are obtained both for AFF and for recirculation after an accurate optimization of the AFF tuning parameters. Based on DoE data, a gain of 25% on the weight of the anodic line has been identified compared to pulsed ejector architecture and 43% with the classic recirculation architecture with blower only (Miraï).     

An experimental approach towards increasing mechanical durability of extruded fish feed in the drying process

Mechanical durability of extruded fish feed must be optimized to lower economic losses as well as emission of organic matter to aquatic environments. The glass transition hypothesis for viscoelastic biopolymers is demonstrated and confirmed experimentally to be valid for extruded fish feed pellets. It is proposed and demonstrated that it is important to avoid early glass transition onset, to optimize the obtained mechanical durability. From the proposed glass transition hypothesis, immediate process relevance to the pre-drying transport mechanism is demonstrated. Furthermore, measured mechanical durability is found to range from 1.5 to 5.0% loss, for different combinations of drying parameters.     

Stereo matching cost computation based on nonsubsampled contourlet transform

A new matching cost computation method based on nonsubsampled contourlet transform (NSCT) for stereo image matching is proposed in this paper. Firstly, stereo image is decomposed into high frequency sub-band images at different scales and along different directions by NSCT. Secondly, by utilizing coefficients in high frequency domain and grayscales in RGB color space, the computation model of weighted matching cost between two pixels is designed based on the gestalt laws. Lastly, two types of experiments are carried out with standard stereopairs in the Middlebury benchmark. One of the experiments is to confirm optimum values of NSCT scale and direction parameters, and the other is to compare proposed matching cost with nine known matching costs. Experimental results show that the optimum values of scale and direction parameters are respectively 2 and 3, and the matching accuracy of the proposed matching cost is twice higher than that of traditional NCC cost.     

Kinetic,thermodynamic parameters and in vitro digestion of tannase from Aspergillus tamarii URM 7115

Tannase is an enzyme used in various industries and produced by a large number of microorganisms. The aim of this study was to evaluate tannase production to determine the biochemical, kinetic, and thermodynamic properties and to simulate tannase in vitro digestion. The tannase-producing fungal strain was isolated from “jamun” leaves and identified as Aspergillus tamarii. Temperature at 26°C for 67?h was the best combination for maximum tannase activity (6.35-fold; initial activity in Plackett–Burman design—15.53?U/mL and average final activity in Doehlert design—98.68?U/mL). The crude extract of tannase was optimally active at 40°C, pH 5.5 and 6.5. Moreover, tannase was stimulated by Na⁺, Ca²⁺, Mg²⁺, and Mn²⁺. The half-life at 40°C lasted 247.55?min. The free energy of Gibbs, enthalpy, and entropy, at 40°C, was 81.47, 16.85, and ?0.21?kJ/mol?·?K, respectively. After total digestion, 123.95% of the original activity was retained. Results suggested that tannase from A. tamarii URM 7115 is an enzyme of interest for industrial applications, such as gallic acid production, additive for feed industry, and for beverage manufacturing, due to its catalytic and thermodynamic properties.