不同晶相结构ZrO2负载铜基催化剂用于二乙醇胺脱氢反应

通过制备不同晶相结构〔单斜相(m-ZrO_2)、四方相(t-ZrO_2)和无定型(a-ZrO_2)〕ZrO_2载体,再通过沉积沉淀法制得Cu/m-ZrO_2、Cu/t-ZrO_2和Cu/a-ZrO_2催化剂,分别用于催化二乙醇胺脱氢合成亚氨基二乙酸反应。采用XRD、氮气物理吸附脱附、XPS、H_2-TPR、CO_2-TPD对催化剂的结构进行了表征。结果表明,Cu/m-ZrO_2催化剂界面更加有利于Cu~+/Cu~0稳定存在,具有更多的碱性位点,且抗氧化性较好。在二乙醇胺脱氢反应中,Cu/m-ZrO_2催化剂性能最好,反应时间为2.5 h,亚氨基二乙酸收率为97.64%。     

The World robot summit disaster robotics category – achievements of the 2018 preliminary competition

The World Robot Summit is a robot Olympics and aims to be held in a different country every four years from 2020. The concept of the Plant Disaster Prevention challenge is daily inspections, checks, and emergency response in industrial plants, and in this competition, robots must carry out these types of missions in a mock-up plant. The concept of the Tunnel Disaster Response and Recovery challenge is emergency response to tunnel disasters, and is a simulation competition whereby teams compete to show their ability to deal with disasters, by collecting information and removing debris. The Standard Disaster Robotics challenge assesses, in the form of a contest, the standard performance levels of a robot that are necessary for disaster prevention and emergency response. The World Robot Summit Preliminary Competition was held at Tokyo Big Sight in October 2018, and 36 teams participated in the Disaster Robotics Category. UGVs and UAVs contended the merits of new technology for solving complex problems, using core technologies such as mobility, sensing, recognition, performing operations, human interface, autonomous intelligence etc., as well as system integration and implementation of strategies for completing missions, gaining high-level results.     

LWIP协议在STLite/OS20操作系统中的移植

介绍了免费的TCP/IP协议栈LWIP开发工具和环境,分析了如何实现LWIP的移植,并给出了一种嵌入式系统与网络互联的新思路。     

大牛地气田异常修正等时试井资料求取产能方法

大牛地气田为低渗-致密气田,因存在启动压力梯度等因素,修正等时试井曲线按常规方法处理出现异常,无法准确获取气井的产能方程.采用LIT法和异常曲线校正法对气田异常试井资料进行了重新处理,最终获得气井产能方程,为同类气藏产能试井可能出现的异常资料处理解释探索了新的途径.     

基于Internet的远程教育系统模型研究

随着计算机网络技术的发展，远程教学系统的结构发生了重大的变化，逐步由原来的客户机／服务器(C／S)结构转变为基于Internet的浏览器／服务器(B／S)结构。本文提出了基于CORBA技术的B／S结构系统模型。分析了其运行过程，并与传统的结构进行了比较，指明了其优越性。在本文的结尾。指出了使用这种技术的一个具体例子。     

纤维在沥青混合料中的应用研究

选用工程中常用的几种纤维,结合工程应用要求,试验分析了纤维的吸湿性、耐热性,并通过网篮析漏试验、动态剪切试验和沉锥试验,讨论了纤维对沥青的稳定和吸附作用,以及纤维对沥青混合料“加筋”效果和作用机理。研究表明有的纤维“吸附、稳定”性能好,而有的纤维“加筋、桥接”效果好,在应用纤维时,应根据纤维的主要特点以及沥青混合料的使用要求来选用。     

浅谈DC/DC变换器控制新方法

文中针对DC/DC变换器的特点,在现有控制和建模方法的基础之上,对DC/DC变换器的现代控制方法进行了归纳和总结,简要讨论了其控制原理,并比较了各种现代控制方法的优缺点,最后对DC/DC变换器控制方法的发展作了一定的展望。     

Use of the Retarded Solution-Reprecipitation Process to Attain a Higher Initial Permeability in MnZn Ferrites

We investigated the effect of various amounts of liquid phase on microstructure development during sintering and the resulting magnetic permeability of MnZn ferrite (MZF) samples. Our results revealed that the microstructure and the final magnetic permeability depend on the thickness of the liquid-phase film during sintering. The solution-reprecipitation (S-R) process, which is associated with an intensive microstructure development in MZF, starts when a continuous liquid-phase film of critical thickness δ_o, which wets the MZF grains, is formed. The solid-state sintering that takes place before the formation of the continuous liquid-phase film is essential for the final microstructure of MZF.     

Mass Transfer in a Flat Gas/Liquid Interface using non‐Newtonian Media

Gas/liquid mass transfer has been investigated using a stirred vessel gas/liquid contactor using non‐Newtonian media and carbon dioxide as absorbent and gas phase, respectively. The volumetric mass transfer coefficients at different operational variables have been determined. Non‐Newtonian media (liquid phase) were prepared as aqueous solutions of sodium carboxymethyl cellulose salt. The influence of the rheological properties, polymer concentration, stirring rate, and gas flow rate on mass transfer was studied for these liquid phases. Kinematic viscosity and density experimental data were used to calculate the average molecular weight corresponding to the polymer employed. The Ostwald model has been used to fit the rheological behavior of aqueous solutions of the polymer employed as absorbent phase. Reasonably good agreement was found between the predictions of the proposed models and the experimental data of mass transfer coefficients.     

Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry