Formation and growth mechanism of TiC crystal in TiC_p/Ti composites

1　ＩＮＴＲＯＤＵＣＴＩＯＮＰａｒｔｉｃｌｅｓｒｅｉｎｆｏｒｃｅｄｔｉｔａｎｉｕｍａｌｌｏｙｍａｔｒｉｘｃｏｍｐｏｓｉｔｅｓ(ＴＭＣｐ)ｈａｖｅｗｉｄｅａｐｐｌｉｃａｔｉｏｎｆｉｅｌｄｓｆｏｒｔｈｅｉｒａｔｔｒａｃｔｉｖｅｈｉｇｈｓｐｅｃｉｆｉｃｓｔｒｅｎｇ     

The microstructure of Cu films deposited by the self-ion assisted technique

The microstructures of Cu films deposited by the self-ion assisted, partially ionized beam (PIB) deposition technique under two different accelerating potentials, 0 KeV and 6 KeV, are compared. The 6 KeV film shows a bimodal (111) fiber and (100) fiber texture with an abundance of twin boundaries and a relatively large average grain size with a typical lognormal distribution. The 0 KeV film consists of small, mostly (111) oriented grains with islands of abnormally large (100) grains. The controlling factors for the abnormal growth of the (100) grains are discussed in relation to the observed microstructures, showing that all factors necessary for abnormal (100) growth are present in the films.     

Growth Stresses in the Oxide Scales on TiAl Alloys at 800 and 900°C

In the oxidation of TiAl alloys, the role of scale-growth stresses formed during oxidation has, thus far, been unknown. In the present paper the oxide-growth stresses were investigated by the deflection-test method in monofacial oxidation (DTMO) accompanied by acoustic-emission measurements. On unmodified surfaces the growth stresses are compressive and reach levels of around –100 MPa. At the same time, significant acoustic emission occurs indicating that even under isothermal conditions, stresses are relieved by a scale-cracking mechanism. For oxide scales on TiAl surfaces, which had been ion implanted with chlorine before oxidation, a very thin protective alumina layer is formed which, however, develops growth stresses in the range of several GPa, accompanied by intensive acoustic emission. In all stress–time curves, a dynamic situation is observed. This consists of phases of stress relief by scale microcracking and phases of stresses increase due to crack healing and further oxide growth. As a result, the level of stress as a function of oxidation time, is characterized by an oscillating course.     

Microscopic and Macroscopic Growth Rates of Fatigue Cracks in Steels and Alloys under the Influence of Crack Closure

On the basis of the experimental data, we show that the difference between the macroscopic and microscopic fatigue crack growth rates in the second section of the kinetic diagram of fatigue fracture is caused by the effect of crack closure within the limits of its existence. We establish the relationships between the macroscopic and microscopic fatigue crack growth rates and the structure of the material in the second section of the diagram for various values of the load ratio with regard for the effect of crack closure and propose a procedure of examination of the fracture processes in structural materials based on the analysis of microscopic and macroscopic fatigue crack growth rates.     

Optimized species growth in epoxy polymerization with real-coded NSGA-II

Satisfaction of twin objectives of maximization of M_n along with minimization of PDI do not necessarily guarantee the maximization of concentration of desired species in a semibatch epoxy polymerization process. As the final product consists of a number of polymer species, a need is felt to perform an advanced optimization study to come up with such process conditions for which the selective growth of a particular polymer species is maximized in minimum possible processing time and the population of other species should be at their lowest values. These above-mentioned conflicting objectives frame the platform for a multi-objective optimization problem, which is solved here using a real-coded non-dominated sorting genetic algorithm or NSGA II and Pareto optimal solutions are obtained. The decision variables are discrete addition rates of various ingredients, e.g. the amount of addition of bisphenol-A (a monomer), sodium hydroxide and epichlorohydrin at different time steps. All species balance equations, bounds on M_n, PDI and addition amounts are treated as constraints. Results are very promising in terms of optimized operations for selective enhancement of desired polymer species for the epoxy polymerization process. Total additions are kept very close to available experimental conditions to minimize probable extrapolation errors. It has been observed that preferential oligomer production is extremely difficult for epoxy polymerization. Lower chain polymers are the only choice for a good quality, stable polymer product.     

Grain growth kinetics in Dy-doped Bi0.5Na0.5TiO3 ceramics

Dysprosium-doped bismuth sodium titanate ceramics were prepared using the conventional mixed-oxide method. The amount of dysprosium used was varied from 0 to 2 at.%. The mixed powders were calcined at 800 °C and checked for phase purity using X-ray diffraction technique. The calcined powders were then cold-pressed into pellets and sintered at 1050 °C for the time ranging from 2 to 48 h. The ceramics were checked for phases and microstructures using an X-ray diffractometer and a scanning electron microscope, respectively. The analysis showed that undoped BNT ceramics sintered at longer time exhibited a significant grain growth with non-uniform grain size distribution and shape. The Dy-doped BNT however showed a much more limited grain growth behavior, resulting in smaller grain size and more equiaxed grain shape. It was also found that all Dy-doped BNT ceramics sintered at 48 h possessed lower porosity than those sintered for shorter time.     

Highly oriented star-like patterns observed on GaSe epilayers grown on Si(111)

Epitaxial lamellar gallium selenide (GaSe) semiconductors have been grown on trench-patterned silicon (Si) substrates by molecular beam epitaxy. An intriguing star-like patterned morphology was identified by atomic force microscopy on these epilayers. This non-trivial feature can be correlated with the accumulation of stacking faults of two concurrent epitaxial domains around self-oriented triangular pits developed earlier on the Si(111) surface by the chemical etching. Crystallographic considerations show how the stars can be formed.     

Sintering studies of nano-crystalline zinc oxide

Sintering and grain growth of nano-crystalline undoped ZnO has been studied in detail over a wide range of temperature and holding time. Below 800 °C, sintering of over 70% theoretical density is not observed, irrespective of particle size. At 900 °C for 6 h, the nano-crystalline sample sinters to 99% of theoretical density whereas the density for as received sample is 93% of theoretical density. However, at 1300 °C or higher, the densification is found to be much faster and after a few hours becomes independent of holding time. Grain growth studies reveal a similar feature of attaining saturation over holding time. The average saturated grain size is found to be ∼1.5 and ∼2.2 μm at 800 and 900 °C, respectively, while at 1300 °C or higher, it is in between 12 and 13 μm.