Residual strain in cadmium telluride/gallium arsenide (001) heterostructures as a function of temperature

Optical studies of residual strain in cadmium telluride (CdTe) films grown using molecular beam epitaxy on gallium arsenide (GaAs) substrate have been performed using photoreflectance techniques. Measurements have been conducted to determine the fundamental transition energy, heavy-hole and light-hole transition energy critical-point parameters in a range of temperatures between 12 and 300 K. There are problems inherent in the fabrication of optoelectronic devices using high-quality CdTe films, due to strain effects resulting from both the lattice mismatch (CdTe: 14.6%) and the thermal expansion coefficient difference. The CdTe film exhibits compressive stress causing valence-band splitting for light and heavy holes. We have used different models to fit the obtained experimental data and, although the critical thickness for the CdTe has been surpassed, the strain due to the lattice mismatch is still significant. However, the strain due to the thermal expansion is dominant. We have found that the fundamental transition energy, E₀, is affected by the compressive strain and the characteristic values are smaller than those reported. In addition, the total strain is compressive for the full measured range, since the strain due to the lattice mismatch is one order of magnitude higher than that calculated from the thermal expansion.     

Experimental and modeling approaches of MR behaviors under large step strains

Rheological properties of MR fluids under large step strain shear are presented in this paper. The experiments were carried out using a rheometer with parallel-plate geometry. Under the large step strain shear, MR fluids behave as nonlinear viscoelastic properties, where the stress relaxation modulus, G(t, γ), shows a decreasing trend with step strain. The experimental results indicate that G(t, γ) obeys time-strain separability. Thus, a mathematical form based on finite exponential serials is proposed to predict MR behavior. In this model, G(t, γ) is represented as the product of a linear stress relaxation, G(t), and the damping function, h(γ), i.e. G(t, γ)=G(t) h(γ). G(t) is simply represented as a three-parameter exponential serial and h(γ) has a sigmoidal form with two parameters. The parameters are identified by adopting an efficient optimization method proposed by Stango et al. The comparison between the experimental results and the model-predicted values indicates that this mathematical model can accurately predict MR behavior.     

Development of geometrically exact new shell elements based on general curvilinear co‐ordinates

In the present study first‐order shear deformable shell finite elements based on general curvilinear co‐ordinates are proposed. For the development of the present shell elements, a partial mixed variational functional with independently assumed strains is provided in order to avoid the severe locking troubles known as transverse shear and membrane lockings. Bubble functions are included in the shape function of displacement to improve the performance of the developed element. The proposed assumed strain four‐ and nine‐node elements based on the general tensor shell theory provide an efficient linkage framework for shell surface modelling and finite element analysis. In the several benchmark problems, the present shell elements with exact geometric representations demonstrate their performance compared to previously reported results. Copyright © 2002 John Wiley & Sons, Ltd.     

Long multifilament Bi-2223 Ag-sheathed superconducting tapes and solenoids

Multifilament Ag-sheathed BiPbSrCaCuO (2223) superconducting tapes containing 49 filaments were fabricated by the powder-in-tube route and the roll-anneal process. The transport critical current densityJ _c was 1.3×10⁴ A cm^–2 at 77 K and 7×10⁴ A cm^–2 at 4.2 K in self-field. A 12-m-long tape was used to construct superconducting solenoids (50, 28, and 14 mm internal diameters) generating dc fields 380–1070 G at 4.2 K. Measurements of the variation ofJ _c with field (0–1.6 T) and bend strain (0–5%) are used to explain the performance of the solenoids. The critical bend strain of tapes was about 1.5%.     

Deformation of Rodlike Elements of Composite Materials Subjected to Uniform Compression

On the basis of generalization of the results of investigation of the operation of rodlike elements of composite materials, we make a conclusion that the influence of various factors on the deformability of these elements is studied incompletely. The comparison of the stress-strain states for different models of concrete and reinforced-concrete elements makes it possible to describe the effect of longitudinal reinforcement (coefficient of reinforcement, strength and deformation characteristics) on the critical level of strains in the cross section. According to the results of our investigations, we give recommendations concerning the evaluation of the critical value of the coefficient of reinforcement above which one may observe the effect of reinforcement on the deformability of the analyzed sections. It is shown that the compression strength of the brittle base of the composite with inhomogeneous structure decreases as a result of the fracture processes. It is also demonstrated that the existing procedure used for the evaluation of the indicated decrease in strength requires significant improvement. The problem of evaluation of the ultimate value of the coefficient of reinforcement is also analyzed.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Precision equipment for symmetrical bending— Part 1. The loading system

The design and performance of precision bending equipment for testing straight beams with constant rectangular section under a pure bending moment is described. Part 1 deals with the loading arrangements and Part 2 with the rig for measuring beam deflection. The methods for recording deflection of strain gauges applied on the beam have been described elsewhere.^1–4
The reactions to the deadweight gravity loads are taken via ball bearings. The total bending moment inaccuracy, i.e. the sum of estimated systematic errors and random errors, the latter expressed as the 2Ga confidence interval about the mean (2G_cim), is about ± 25 x. 10^-4%, for 23 tests with a steel beam with 15 mm × 75 mm cross sectional dimensions, loaded to 1-1.5 mm/m strain.
The measuring rig stands on the beam via hardened and polished spherical segment feet and uses a capacitive transducer system with less than 5nm resolution. Various application tasks are described. The total inaccuracy of the measured deflection, i.e. apart from bending moment inaccuracy, is about ± 35 times 10^4% for about 10 reproduced, not repeated, tests with the same steel beam. The deflection for such a beam is of the order of 2 to 4 mm.     

Production and structural features of a water-soluble polysaccharide from a mutant strain of Agrobacterium sp.

We have developed a mutant strain derived from Agrobacterium sp. ATCC 31750, which produces a water-soluble polysaccharide having potential utility to the food, feed, pharmaceutical and cosmetic industries. A high concentration of product (15 g/L) is obtained by 48 h cultivation of the mutant strain under optimized fermentation conditions. The water-soluble polysaccharide obtained from cultures of the mutant strain beta82 has Glc:Man:Gal in approximate molar ratios of 5.8:6.7:1.0. The molecular weight of the polysaccharide was determined to be approximately 1000 kDa by HPSEC analysis. Linkage analysis contained 3-Glcp, 3-Manp, terminal Glcp and terminal Manp, as well as a small proportion of 3- and 3,4-Galp, and 4,6-Manp residues. Based on analyses using FT-IR and ¹³C NMR spectrometers, most glycosidic bonds joining these sugar residues are of the α-type, and acetyl groups are apparently attached to the polymer chain at random.