Estimation of the Stress-Strength Reliability for Exponentiated Pareto Distribution Using Median and Ranked Set Sampling Methods

In reliability analysis, the stress-strength model is often used to describe the life of a component which has a random strength (X) and is subjected to a random stress (Y). In this paper, we considered the problem of estimating the reliability R=P [Y<X] when the distributions of both stress and strength are independent and follow exponentiated Pareto distribution. The maximum likelihood estimator of the stress strength reliability is calculated under simple random sample, ranked set sampling and median ranked set sampling methods. Four different reliability estimators under median ranked set sampling are derived. Two estimators are obtained when both strength and stress have an odd or an even set size. The two other estimators are obtained when the strength has an odd size and the stress has an even set size and vice versa. The performances of the suggested estimators are compared with their competitors under simple random sample via a simulation study. The simulation study revealed that the stress strength reliability estimates based on ranked set sampling and median ranked set sampling are more efficient than their competitors via simple random sample. In general, the stress strength reliability estimates based on median ranked set sampling are smaller than the corresponding estimates under ranked set sampling and simple random sample methods.     

动态高压微射流处理对方竹笋膳食纤维理化及结构特性的影响

以方竹笋中提取的膳食纤维为研究对象，采用动态高压微射流（dynamic high-pressure micro-fluidization, DHPM）在不同压力条件（0，50，100，150，200 MPa）下进行处理，探究其对竹笋膳食纤维（bamboo shoots dietary fiber, BSDF）理化和结构特性的影响。结果表明，随着处理压力的增大，BSDF粒径先增大后减小，当处理压力为150 MPa时，粒径最小，为（370±11） nm，此条件下BSDF的持水力、持油力和膨胀力达到最大，较对照组分别提高了47.74%，50.54%，61.27%，且差异显著（P<0.05）。红外光谱分析表明DHPM处理不会改变BSDF的官能团，但会使BSDF内部的部分氢键断裂和半纤维素、木质素等发生降解；X射线衍射和热重分析表明DHPM处理不会引起BSDF的晶体结构改变，但晶体有序度会下降，进而导致其热稳定性降低；微观结构分析显示DHPM处理会使BSDF颗粒尺寸减小、表面粗糙、组织松散，且当处理压力为200 MPa时，颗粒发生团聚。综上，DHPM可以有效改善BSDF的理化性质，在膳食纤维改性方面具有一定的应用价值。     

数字化正弦平方脉冲信号

依据正弦平方脉冲的数学方程及其频谱分布，分别导出了与理想和标称视频带宽相对应的正弦平方脉冲的数学表达式及其编程生成方法。实验表明，此法不仅精确，而且便于修改参数，并可直接读人数字电视系统，来测定视频线性响应。     

心电地图仪中工频干扰的一种滤除方法

在心电地图仪中记录到的体表心电信号往往由于电磁的影响而引进工频干扰．基于体表心电信号中工频干扰的特点，作者提出了一种滤除工频干扰的方法，即就单独—胸导联信号通过提高频谱的分辨率来估计工频干扰的频率；基于最小均方误差准则来估计各导联信号中工频干扰的幅度和相位。文中还给出了该算法的流程图和滤波性能分析。模拟结果表明了该算法的有效性。应用该算法对心电地图仪中的工频干扰进行对消，取得了满意的结果。     

Corner flow in free liquid films

A lubrication-flow model for a free film in a corner is presented. The model, written in the hyperbolic coordinate system ξ = x ² −y ², η = 2xy, applies to films that are thin in the η-direction. The lubrication approximation yields two coupled evolution equations for the film thickness and the velocity field which, to lowest order, describes plug flow in the hyperbolic coordinates. A free film in a corner evolving under surface tension and gravity is investigated. The rate of thinning of a free film is compared to that of a film evolving over a solid substrate. Viscous shear and normal stresses are both captured in the model and are computed for the entire flow domain. It is shown that normal stress dominates over shear stress in the far field, while shear stress dominates close to the corner. This revised version was published online in October 2005 with corrected page numbers.     

A VLSI architecture for a half-edge-based corner detector

Corner detection is a low-level feature detection operator that is of great use in image processing applications, for example, optical flow and structure from motion by image correspondence. The detection of corners is a computationally intensive operation. Past implementations of corner detection techniques have been restricted to software. In this paper we propose an efficient very large-scale integration (VLSI) architecture for detection of corners in images. The corner detection technique is based on the half-edge concept and the first directional derivative of Gaussian. Apart from the location of the corner points, the algorithm also computes the corner orientation and the corner angle and outputs the edge map of the image. The symmetrical properties of the masks are utilized to reduce the number of convolutions effectively, from eight to two. Therefore, the number of multiplications required per pixel is reduced from 1800 to 392. Thus, the proposed architecture yields a speed-up factor of 4.6 over conventional convolution architectures. The architecture uses the principles of pipelining and parallelism and can be implemented in VLSI.     

试论双点后方交会简便公式

根据双点后方交会的图形特点和已知条件，列出了方程组，推导出了双点后方交会直接计算座标的简便公式，同时求出了精度计算公式，以供测量人员参考     

f—x域内提高地震资料的信噪比

在 f-x 域,地震记录可以表示成有限个调频调幅正弦波的叠合,叠合的结果是一个连续且光滑的函数。我们可以用一个简单的 n 次多项式去逼近这个函数。本文提出了一种在 f-x 域用最小平方拟合原理消除随机噪声的新方法,并证明了在噪声为自噪以及空间采样足够密的条件下,拟合结果与噪声无关,即 f-x 域最小平方拟合处理可以有效地消除记录上的随机白噪,而对有效信号的破坏甚微。由于理论上允许振幅值及同相轴形态在空间上发生变化,因而该方法不具有混波作用,是高分辨率处理的理想工具。     

A TVD Scheme for Incompressible Flow Coupled With Different Turbulence Modles on A Ground-Mounted Square-RIB Flow

A finite-difference Total Variation Diminishing (TVD) numerical simulation model for coupling the Reynolds Averaged Navier-Stokes (RANS) equations, pressure-relative continuity equation and various k-ε turbulence models was developed to solve the incompressible flow based on the pseudo-compressibility method. The hyperbolicity of all these equations was studied and the discretization of the fully coupling equations with all the primal variables and source terms were made in this article. Numerical simulation for modeling the flow around a ground-mounted square rib was implemented and validated by comparing with the published wind tunnel experimental data. It is shown that such a numerical simulation method with a proper turbulence model has a very good accuracy to simulate the flow around a surface-mounted rib. It is concluded that the Renormalization Group (RNG) and Chen-Kim k-ε turbulence models have much better ability to predict the characteristics of the vortex structure and flow separation than the standard k-ε model.     

8字形管角部裂纹问题研究

冷弯异型管在角部存在应力集中现象，有时存在裂纹倾向。通过对沈阳东洋异型管有限公司一异型管产品——8字形管产生裂纹的原因进行分析，确定了解决方案：①修理轧辊，加大有开裂倾向的内陷角；②选用塑性更好的板材。实践证明，该措施能有效地防止管角角部裂纹的产生。