Densities and Viscosities of Oleic Acid at Atmospheric Pressure

The densities of oleic acid were measured over the temperature range from (293 to 459) K at atmospheric pressure using a densimeter based on the modified hydrostatic weighing method. The dynamic viscosities of the same oleic acid sample were measured using a capillary viscometer (VPZ-2 m) in the range from (293 to 363) K at atmospheric pressure. The combined expanded uncertainty of the density, atmospheric pressure, viscosity, and temperature measurements at the 95% confidence level with a coverage factor of k = 2 is estimated to be 0.15%, 1.0%, 3.5%, and 15 mK, respectively. The values of uncertainty for density and viscosity include the effects of purity and calibration (total expanded uncertainty). These experimental data were used to develop wide-range correlations for the density and viscosity based on theoretically confirmed Arrhenius–Andrade and Vogel-Tamman-Fulcher (VTF) models. The value of the glass temperature ( T _g= 179.78 K.) for the oleic acid was estimated using the VTF parameters derived from the present viscosity measurements. To additionally validate the reliability of the measured density data, the same oleic acid samples were measured using the pycnometric method. The present study showed that the densities measured using the modified hydrostatic weighing densimeter (HWD) agree with the values obtained using the pycnometric method within 0.09% for Sample 1 and 0.25% for Sample 2.     

Characteristics of hydrostatic bearing/seal parts for water hydraulic pumps and motors. Part 1: Experiment and theory

In this paper, the load-carrying capacity, power losses and stiffness of disk-type hydrostatic thrust bearings including the case of eccentric loading are discussed theoretically. The numerical analysis method is established based on a two-dimensional elastohydrostatic problem with an elastic deformation model, which is extended to adapt it for a non-axisymmetric load acting on the thrust bearing. The bearing is made of a combination of stainless steel/stainless steel and stainless steel/plastics. For the elastic materials, the maximum stiffness derived from, i.e., minimum film thickness is, larger than that of the rigid material in the range of a large ratio of pocket pressure and a hydrostatic balance ratio of over unity, which is defined as the ratio of the load to the maximum hydrostatic load-carrying capacity. The maximum load-carrying capacity and minimum power loss can exist in the domain of the hydrostatic balance ratio over unity for the case of the bearing consisting of elastic/rigid materials, in comparison with that composed of the same rigid materials. For the case of water, the power loss due to leakage flow is slightly larger but that due to frictional torque is much smaller than that in the case of hydraulic oil. Then, the total power loss is much smaller than that of hydraulic oil.     

电子衡器特殊故障的分析及处理

因为电子衡器在安装与调试过程中出现的较为特殊的故障，难以找出正确的起因与处理方法，所以介绍了如何保证电子衡器的正常使用和计量准确性的工作体会。     

Development of a Magnetic Suspension Densimeter and Measurement of the Density of Toluene

The development of a magnetic suspension densimeter that has been built for measurement of the density of compressed liquid at pressures up to 30 MPa in the temperature range 20 to 150°C is described. The densimeter was first built by the author and his coworkers at NIST. We describe here further improvements made on a second system built at NMIJ based on the same principle. The densimeter uses a small coil suspended from an electronic balance. Within the coil is placed a sample cell in which the pressurized sample and a buoy, which is a permanent magnet, are enclosed. For measurement of density, balance readings are recorded (1) with the buoy at rest and (2) with the buoy in magnetic suspension. The measurement procedure is basically a hydrostatic weighing, which is simpler than those of conventional magnetic densimetry. As an example, measurements of toluene density performed as part of an inter-laboratory comparison are presented. The data agreed with reliable literature values to within a few hundredths of a per cent.     

计量秤在变角度状态的实践

介绍了物料计量秤在变角度下如何计算重量，以及变角度显示仪的工作原理和在实际中的运用。     

Metrological Support and Standards in the Design,Production, and Use of High-Load Weighing Machines in Russia

An analysis is presented on development, production, and use of high-capacity weighing machines in Russia in the last ten years. Aspects arising in type approval testing are considered for high-capacity weighing machines working over wide temperature ranges.     

高炉焦炭中子测水与干焦重量补偿模型

文章叙述了高炉焦炭的中子测水原理，并给出了一种干焦重量的补偿方法，最后用一个例子说明实际的效果。     

原料对铁合金冶炼过程的影响

介绍了铁合金冶炼时需要准备的原料，对不合格原料需要进行加工处理，达到合格粒度。并提出了影响铁合金冶炼过程有原料的粒度，配料称量，混合等重要因素。     

RADIOACTIVE OR NATURAL TRACER。TECHNIQUES FOR LEAK DETERMINING OF DAM ABUTMENT

Infiltration and localization of preferential infiltration zones at the dam abutment are measured using radioactive tracer tests of flow in boreholes,meanwhile interconnection between boreholes and the energing water points is analysed.The theory and practice of radioactive tracer synthetic detective method are described to give methods and calculation formulae used under the condition of stable flow in single well to measure permeability coefficient and hydrostatic heads.Major single hole techniques including measurement for seepage line,velocity,rate of seepage flow and relationship of recharge of groundwater in aquifers are introduced briefly.The possibilities offered by natureal tracers are analysed,uincluding electric-conduct,pH-value and temperature of water as well as stable isotopes(D,^18O) and tritium.Furthermore,the sensibilities of this theory and methods were confirmed by detecting seepage flow field of Xinanjiang Dam.     

天车称重系统解析

以河北钢铁集团唐山钢铁有限责任公司一钢轧厂240t天车称重系统为例,介绍天车称重系统的硬件结构、工作原理、传输方式、仪表功能、称重传感器原理、钢丝绳补偿、信号传输、称重仪表等,结合在生产中的实际运行状况,总结出在生产维护中的常见问题,并提出具体的解决方法。