Experimental study on the heat transfer and flow characteristics of nanorefrigerants inside a corrugated tube

The heat transfer and flow characteristics of MWCNT-R141b nanorefrigerant with different mass fractions have been studied through experiments. Experimental results were compared with existing correlations. A two-step method was used to prepare the nanorefrigerants. Span-80 was used as surfactant with an average particle diameter of 20 nm. Transmittance method was used to evaluate the stability of nanorefrigerants. Results showed that the stability of MWCNT-R141b nanorefrigerant, which is the added dispersant, was good during the experiments. The 0.3 wt% MWCNT-R141b nanorefrigerants had optimal heat transfer enhancement effects compared with pure refrigerants. The maximum Nusselt number increased by 40%. The specific pressure drop of nanorefrigerant increased as the Reynolds number (Re) increased, and the specific pressure drop of the pure refrigerant was minimum, which is similar to R141b.     

Theoretical study of a thermoelectric-assisted vapor compression cycle for air-source heat pump applications

This paper proposes a thermoelectric-assisted vapor compression cycle (TVCC) for applications in air-source heat pump systems which could enhance the heating capacity of the system. Performances of TVCC are calculated and then compared with that of basic vapor compression cycle (BVCC). The simulation results show that when coefficients of performance (COPs) of the two cycles are almost equal, the TVCC under maximum COP condition of the thermoelectric modules still performs better than BVCC by 13.0% in heating capacity through selecting the appropriate intermediate temperature. In addition, the TVCC can also achieve an improvement of 16.4%–21.7% in both the heating COP and capacity when compared with the BVCC with an assistant electric heater that is provided with the equivalent power input of thermoelectric heat exchanger. Thus, the TVCC could be beneficial to the applications in small heat pumps if there is always need for auxiliary electric heat.     

基于热负荷自动调节的延迟焦化加热炉三点注汽量智能优化

针对国内某炼油厂延迟焦化加热炉三点注汽问题，采用热负荷自动调节的算法进行了研究。运用该模型方法，分析了三点注汽量对加热炉热负荷和炉管结焦系数的影响，发现三点注汽量的改变均会对热负荷和炉管结焦系数产生影响，主要表现为提高注汽量将会提高热负荷，同时降低结焦系数；第1点注汽量和第2点注汽量对热负荷和结焦系数的影响较强，第3点注汽量对热负荷和结焦系数的影响较弱。在实际操作中，加热炉中的结焦程度既不能太强也不能太弱，合适的结焦系数能够保证正常开工周期里炉管不结焦，也能保证瓦斯、注汽量等参数的合理分配。通过对热负荷、注汽量的智能分配，可得到不同原料油加工负荷条件下更加合理的装置运行方案。     

Application of Vis–NIR hyperspectral imaging in classification between fresh and frozen-thawed pork Longissimus Dorsi muscles

Fresh and frozen-thawed (F-T) pork meats were classified by Vis–NIR hyperspectral imaging. Eight optimal wavelengths (624, 673, 460, 588, 583, 448, 552 and 609 nm) were selected by successive projections algorithm (SPA). The first three principal components (PCs) obtained by principal component analysis (PCA) accounted for over 99.98% of variance. Gray-level-gradient co-occurrence matrix (GLGCM) was applied to extract 45 textural features from the PC images. The correct classification rate (CCR) was employed to evaluate the performance of the partial least squares-discriminate analysis (PLS-DA) models, by using (A) the reflected spectra at full wavelengths and (B) those at the optimal wavelengths, (C) the extracted textures based on the PC images, and (D) the fused variables combining spectra at the optimal wavelengths and textures. The results showed that the best CCR of 97.73% was achieved by applying (D), confirming the high potential of textures for fresh and F-T meat discrimination.     

Vapor absorption by LiBr aqueous solution in vertical smooth tubes

Heat and mass transfer in a falling film vertical in-tube absorber was studied experimentally with LiBr aqueous solution. The presented results include the effect of solution flow rate, solution subcooling and cooling water temperature on the absorption in a smooth copper tube 16.05 mm I.D. and 400 mm long. The experimental data in the previous report for a 1200-mm-long tube was also re-examined and compared. It was demonstrated by the observation of the flow in the tube that the break down of the liquid film into rivulets leads to deterioration of heat and mass transfer at lower film Reynolds number or in longer tubes. An attempt to evaluate physically acceptable heat and mass transfer coefficients that are defined with estimated temperature and concentration at the vapor–liquid interface was also presented.     

三种常用面积注水井网的比较与选择

本较系统地分析了三种常用面积井网系统的注水特点。指明了五点井网系统是面积井网中最强化的一种注水方式，适用于低渗透与特低渗透油藏的注水开发。     

塑料模现状及发展趋势

我国塑料模的发展,极其迅速,现已具相当规模。无论是设计水平、加工制造技术,还是 CAD 技术都有了明显提高。本文简明扼要地介绍了国内外塑料模的现状、发展趋势、市场预测,以及“九五”国家规划目标与对策。     

双塔脱丙烷工艺技术

对扬子乙烯装置双塔脱丙烷系统低压塔液泛、高压塔再沸器堵塞等问题进行了技术分析,提出了工艺流程修改方案,完善了双塔脱丙烷技术,对同类装置有参考价值。     

永定新河治理工程几个关键问题的研究

永定新河是天津市防洪的北部防线。由于受海相来沙淤积 ,河道行洪能力大幅度下降。针对永定新河治理工程设计中涉及到的河道淤积治理方案、闸位比选、防潮闸结构型式及施工方法、闸下减淤清淤措施等诸多问题进行了分析和研究 ,提出了相应的措施和建议     

An Approach to Modelling the Forming Process of Sheet Metal-Polymer Composites

Polymer Injection Forming (PIF) and Polymer Injection-Compression Forming (PICF) are new manufacturing technologies for sheet metal-polymer macro-composites, which result from the combination of injection moulding and sheet metal forming. In these processes, a metal blank is formed inside an injection mould by using the pressure of the molten polymer that, after cooling, permanently bonds to the metal sheet creating a fully finished product in only one production step. This paper presents a calibrated multi-physics numerical model of the processes that proves to be suitable to investigate the mutual metal-polymer interactions and to provide a reliable tool in designing the process as well as its control.