Chemische Zusammensetzung und Mikrostruktur polymerabgeleiteter Gläser und Keramiken im System Si–C–O. Teil 2: Charakterisierung der Gefügeausbildung mittels hochauflösender Durchstrahlungselektronenmikroskopie und Feinbereichsbeugung

Chemical Composition and Microstructure of Polymer‐Derived Glasses and Ceramics in the Si–C–O System. Part 2: Characterization of microstructure formation by means of high‐resolution transmission electron microscopy and selected area diffraction Liquid or solid silicone resins represent the economically most interesting class of organic precursors for the pyrolytic production of glass and ceramics materials on silicon basis. As dense, dimensionally stable components can be cost‐effectively achieved by admixing reactive filler powders, chemical composition and microstructure development of the polymer‐derived residues must be exactly known during thermal decomposition. Thus, in the present work, glasses and ceramics produced by pyrolysis of the model precursor polymethylsiloxane at temperatures from 525 to 1550 °C are investigated. In part 1, by means of analytical electron microscopy, the bonding state of silicon was determined on a nanometre scale and the phase separation of the metastable Si–C–O matrix into SiO₂, C and SiC was proved. The in‐situ crystallization could be considerably accelerated by adding fine‐grained powder of inert fillers, such as Al₂O₃ or SiC, which permits effective process control. In part 2, the microstructure is characterized by high‐resolution transmission electron microscopy and selected area diffraction. Turbostratic carbon and cubic β‐SiC precipitate as crystallization products. Theses phases are embedded in an amorphous matrix. Inert fillers reduce the crystallization temperature by several hundred °C. In this case, the polymer‐derived Si–C–O material acts as a binding agent between the powder particles. Reaction layer formation does not occur. On the investigated pyrolysis conditions, no crystallization of SiO₂ was observed.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Dynamic modes of Ti combustion in a coflow of N<Subscript>2</Subscript>-Ar mixture

Combustion of bulk density Ti powder (containing 20 wt % TiN as a diluent) in a coflow of N₂-Ar mixture was investigated upon variation in the nitrogen content of the gaseous mixture. The obtained data are believed to open up new horizons for fabrication of layered and composite ceramics by infiltration-mediated combustion.      

混合集成电路激光功能调值技术

本文提出了激光功能微调技术在高精度混合集成电路上的应用，讨论了关键技术问题，并以实例具体说明。该技术的应用为研制高精度混合集成电路开辟了新途径。     

Early detection of ageing in solder joints through laser probe thermal analysis of the peltier effect

We have recently developed an optical contactless method for testing the quality of solder joints during accelerated thermal cycling ageing processes.¹ The method was based upon the measurement of the dynamic thermal behaviour of the joint to short bursts of Joule heating. It has proved to be efficient in revealing the formation of cracks at the lead-solder interface. We present a method to evaluate ageing at a much earlier stage in the cycling process. We have observed in earlier work,¹ that before cracks appear, structural changes occur in the solder at the lead-solder interface. The thermal response of the solder joint is recorded over time to a Peltier heat perturbation produced by flowing a current pulse through the interface where structural changes occur. The key point in this method is to discriminate the Peltier effect from the Joule thermal response because both effects generate heat. The variation of the early Peltier response in the thermal cycling ageing tests is seen as a quantitative signature of the structural changes in the lead-solder interface.     

硅片和硅器件工艺中的背面损伤吸除技术

本文介绍了硅片背面的三种主要损伤吸除技术：机械损伤、激光辐照和离子注入技术。对这三种吸除技术的机理、工艺条件、应用情况和近来进展，作了详细的评述。     

Non-contact methods of measuring moisture concentration in external layers of building partitions II—Monitoring of the water vapour condensation on porous surfaces

This paper present the results of the investigation into a potential application of laser radiation for the detection of phase transition processes occurring on the surface layers of porous materials. An attempt was made to discuss in the approximation equations, the relationships between coefficients of the reflected light, the temperature and humidity of the surrounding environment. Laser light reflected from the porous surface carries information about the roughness of the structure. The presence of water microdrop on the surface of the porous material, as a result of condensation and thus a phase transition, leads to the phase displacement of individual rays, which is represented by different images. Therefore, a comprehensive analysis of the reflected light parameters allows a dynamic study of the phase transition phenomena without mechanical intervention.     

Thermal Generation of Residual Stress Fields for Purpose of Distortion Minimization

Thermal treatments of steel components with the goal of hardening often result in distortion by releasing the residual stresses which were brought into the specimen during the preceding processing steps. The goal of the presented work is the minimization of this distortion. By generating definite residual stress fields and investigating the resulting distortion, the distortion mechanism can be observed in detail. A flexible and reproducible way to generate such residual stress fields inside a specimen is by means of local thermal treatment with a laser beam. Computer simulations as well as experiments were carried out using an idealized tooth of a gearwheel (finger sample) as a model system. The deformation of the samples due to the laser heat treatment and the stress fields generated inside the samples were determined with respect to different process parameters.     

Plasma properties of laser-ablated St target in air

Ｐｌａｓｍａｐｒｏｐｅｒｔｉｅｓｏｆｌａｓｅｒ－ａｂｌａｔｅｄＳｔｔａｒｇｅｔｉｎａｉｒＷａｎｇＸｉａｎｇ－Ｔａｉ（王象泰）；ＭａｎＢａｏ－Ｙｕａｎ（满宝元）；ＷａｎｇＧｏｎｇ－Ｔａｎｇ（王公堂）；ＦａｎＸｉ－Ｊｕｎ（樊锡君）；ＷａｎｇＪｕｎ（王军）...     

ATO包裹硅酸锆的制备与应用

采用化学共沉淀技术制备了锑掺杂二氧化锡(ATO)包裹硅酸锆的导电粉体,对比了该导电粉体与ATO在防静电陶瓷中的应用效果。结果表明与掺纯ATO相比较,掺入ATO包裹硅酸锆的防静电陶瓷颜色比较浅,并且能明显减少氧化锡的用量,当陶瓷的表面电阻为107Ω/□量级时,用ATO包裹硅酸锆作为导电填料可以节省25%左右的ATO。