加氢反应器头盖密封质量控制探讨

加氢反应器是加氢装置的重要组成部分,反应器头盖因工况复杂,导致密封难度较大,密封不严,会导致整个装置不能正常运转。为此,就其头盖拆装及密封问题进行探讨,提出有效的质量控制措施。     

职业技能鉴定质量分析初探

职业技能鉴定是推行职业资格证书制度的重要环节,鉴定的质量直接关系到职业资格证书的真实性、权威性。通过对试卷的有效性和可靠性的分析,以及对试题难度、区分度的分析,对职业技能鉴定质量的分析方法进行了探讨,阐述了质量分析在职业技能鉴定中的作用。     

圆锥破碎机躯体裂纹的超声波探伤

重点介绍了圆锥破碎机躯体裂纹的超声波检测及缺陷判定的方法,为矿山其它大型设备的裂纹检测提供了经验。     

气液两相流流量的互相关测量

在内径为３０ｍｍ的垂直上升管中，应用互相关分析和Ｕ型光导纤维探针，对水一气两相流和油－气两相流进行了各分相流量测量的实验研究，考虑了流型和雷诺数对流量测量的影响，同时研究了含气率的测量，提出了计算平均含气率的关系式。对水－气两相流，试验的气相折算流速范围为０．２２～３．００ｍ／ｓ，波相折算流速范围为０．１１～３．００ｍ／ｓ；对油一气两相流，试验的气相折算流速范围为０．１０～１９．０１ｍ／ｓ，液相折算流速范围为０．３５～１．６５ｍ／ｓ。     

Potential control under thin aqueous layers using a Kelvin Probe

Kelvin Probes can be modified to control as well as monitor potential. The design and operation of two different Kelvin Probe Potentiostats (KPPs) are described in this paper. One approach uses a permanent magnet and double coil to oscillate the needle at a fixed frequency, an AC backing potential, and software analysis and control schemes. This technique can also control the distance between the tip and sample, thereby tracking the topography of the sample. Both KPPs were used to make measurements on Type 304L stainless steel under thin layers of electrolyte. Cathodic polarization curves exhibited a limiting current density associated with oxygen reduction. The limiting current density varied with solution layer thickness over a finite range of thickness. Anodic polarization curves on 304L in a thin layer of chloride solution resulted in pitting corrosion. The breakdown potential did not vary with solution layer thickness. However, the thin layer was observed to increase in volume remarkably during pit growth owing to the absorption of water from the high humidity environment into the layer with ionic strength increased by the pit dissolution. The open circuit potential (OCP) and solution layer thickness were monitored during drying out of a thin electrolyte layer. Pitting corrosion initiated, as indicated by a sharp drop in the OCP, as the solution thinned and increased in concentration.     

小型化微波功率探头的分析与设计

为了减少传统微波功率测量中由于热损耗所带来的测量误差,本文中应用一种对数二极管检波电路设计了一种小型化的微波功率探头。同时由于在输入端加入了仿真优化的匹配网络,该探头在100MHz-3GHz驻波比得到了明显改善。最终测试结果表明动态范围大于60dB。     

Coarse head pose estimation of construction equipment operators to formulate dynamic blind spots

Several hundred workers die in construction in the United States every year because equipment operators are unable to see their fellow workers during operation of their vehicle. In this paper we propose a step towards improving this situation by providing an automated method based on range imaging for estimating the coarse head orientation of a construction equipment operator. This research utilizes commercially-available low resolution range cameras to measure the continuously changing field-of-view (FOV) of an equipment operator in outdoor construction. This paper presents a methodology to measure so-called dynamic blind spot maps. The dynamic blind spot map is then projected on a known static equipment blind spot map that already exists to each construction vehicle. A robust computational coarse head pose estimation algorithm and results to three different pieces of construction equipment and multiple operators are presented. The developed method has the potential in automatically determining the spaces around vehicles that are currently not in the field-of-view of the vehicle operator thus providing eventually additional means and technology for improving safety in construction.     

超声TOFD原理和方法要领

概述超声衍射时差(TOFD)法基本原理、探头典型布置和检测系统关键性要求,以及检测工艺的实施要领,旨在推进该新技术在国内的推广应用。     

CFD modeling of pilot-scale pump-mixer: Single-phase head and power characteristics

The present work involves single-phase computational fluid dynamics (CFD) simulations of continuous flow pump-mixer employing top-shrouded Rushton turbines with trapezoidal blades. Baffle—impeller interaction has been modeled using sliding mesh and multiple reference frame approaches. Standard k-ε model has been used for turbulence modeling. Several CFD runs representing different combinations of geometric and process parameters have been carried out. Results of CFD simulations have been used to find out two macroscopic performance parameters of pump-mixer—power consumption and head generated by the impeller. The simulation results have been compared with the experimental data obtained on a pilot-scale setup. Good agreement between CFD predictions and experimental results is observed. In most cases, sliding mesh approach is found to perform better than multiple reference frame approach. Details from CFD simulations have been used to have an insight into the pumping action of the impeller.     

一种无线传感器网络中自主选择簇头的聚类算法

在无线传感网络中,传感器节点要定期向基站发送收集的数据。为了支持数据汇总,通过高效的网络组织将节点划分成若干簇。在这种类型的系统中,随着簇头的轮转,每个簇中的簇头选择方法是最具有挑战性的问题,有效的簇头选择算法可以提高网络的续航时间,并减少在WSN中的节点之间的通信开销。提出一个簇内民主方式选举算法来选择簇中的节点作为簇头,用MatLab对算法进行仿真,证明该算法的性能可以有效改善网络的性能。