Localized corrosion of (lean) duplex stainless steels in immersion units of urban wastewater treatment plants

With lower alloying cost and higher mechanical properties, lean duplex stainless steels can be an alternative to the more commonly used austenitic stainless steels. However, these alloys are still not the preferred choice, probably due to a lack of field experience. A study was thus initiated in view of defining the limits of use of selected (lean) duplexes for urban wastewater treatment units. The present paper shows the localized corrosion performance of selected lean duplexes in chloride contaminated solutions. The results are compared with austenitic S30403 and S31603 and with the more standard duplexes S82441 and S32205. The effect of welding was also investigated. Exposures in field municipal wastewater plants were conducted for 1 year in low and high chloride content units. The results show that lean duplexes S32101 and S32202 can be used as alternatives to S30403 and S31603 in low chloride electrolytes. At 500 ppm of chloride content, duplex stainless steel S32304 showed better corrosion resistance than S30403 and S31603. For higher chloride contents (1000 ppm and above) the standard duplexes S82441 and S32205 shall be preferred.     

Geopolymer concrete-filled pultruded composite beams – Concrete mix design and application

The limited research on the geopolymer concrete mix design for targeting a specific strength is identified an obstacle for their effective design and wide use. In this paper, a mix design procedure has been proposed for fly-ash based geopolymer concrete and its use as infill hybrid composite beam is investigated. Then, the structural performance of geopolymer concrete filled hybrid composite beam is investigated to determine their possible application in civil infrastructure. Firstly, a detailed procedure of mix design for fly-ash based geopolymer concrete is presented. Secondly, three hybrid beams filled with geopolymer concrete were prepared and tested in a four-point bending setup to evaluate their flexural modulus and modulus of rupture. Numerical and analytical evaluation of the behaviour of hybrid beam were performed and results showed a good agreement with the experimental investigation. Thirdly, the suitability of the beam for a composite railway sleeper is evaluated and compared with existing timber and composite sleepers. Finally, the beams’ performance in a ballast railway track is analysed using Strand7 finite element simulation software and the results showed that the new concept of using geopolymer concrete as infill to pultruded composite section satisfied the stiffness and strength requirements for a railway sleeper.     

Role of Co in formation of Ni-Ti clusters in maraging stainless steel

The effect of Co addition on the formation of Ni-Ti clusters in maraging stainless steel was studied by three dimensional atom probe (3DAP) and first-principles calculation. The cluster analysis based on the maximum separation approach showed an increase in size but a decrease in density of Ni-Ti clusters with increasing the Co content. The first-principles calculation indicated weaker Co-Ni (Co-Ti) interactions than Co-Ti (Fe-Ti) interactions, which should be the essential reason for the change of distribution characteristics of Ni-Ti clusters in bcc Fe caused by Co addition.     

Driver detection and recognition of lineside signals and signs at different approach speeds

A study was carried out using simulation to investigate driver responses to lineside signals and signs at various approach speeds. The objectives of the study were: (1) to find out whether train speed would significantly affect signal/sign reading; (2) to examine at which point certain types of signs or signals could be detected or recognised, and (3) to determine a speed cut-off level above which certain types of signs or signals are no longer recognisable or detectable. Fifty-seven train drivers from 12 Train Operating Companies in the UK participated in the trials. Twenty different types of lineside signs and ten types of signals were tested under six different approach speeds ranging from 100 to 350 km/h (62–218 mph). Driver performance measures were ‘time remaining to the signal/sign’ at the point of detection or recognition, and reading error rate. The results showed a significant influence of train speed on driver responses to lineside signals/signs and demonstrated a non-linear relationship between driver responses to signals/signs and approach speed. This has been used to estimate a maximum approach speed limit within which a specific signal or sign can be correctly detected or recognised. The findings and implications of the study are discussed in the paper.     

Scheduling railway traffic at a construction site

We consider the problem of rescheduling trains in the case where one track of a railway section consisting of two tracks in opposing directions is closed due to construction activities. After presenting an appropriate model for this situation we derive a polynomial algorithm for the subproblem of finding an optimal schedule with minimal latenesss if the subsequences of trains for both directions outside the construction site are fixed. Based on this algorithm we propose a local search procedure for the general problem of finding good schedules and report test results for some real world instances. Received: December 8, 1999 / Accepted: May 2, 2001     

Quantitative analysis of Ni effect on CCT diagrams of novel air-cooled bainite steels using artificial neural network models

The quantitative effect of Ni content on continuous cooling transformation （CCT） diagrams of novel air-cooled bainite steels was analyzed using artificial neural network models. The results showed that Ni may retard the high- and medium-temperature transformation and martensite transformation. The results conform to the materials science theories.     

青藏铁路西格二线混凝土冻融试验研究

由于工期的要求,青藏铁路西格增建二线必须进行冬期施工。根据工程状况,分析了混凝土受冻的破坏机理,针对施工环境及对混凝土设计强度和要求,进行了大量冻融试验分析,对引气剂、水胶比、砂率、粉煤灰掺量等原材料与混凝土含气量的关系及其混凝土搅拌温度与静停时间等对混凝土性能的影响进行了分析与技术论证,确保了该线冬期混凝土施工顺利进行。     

Brittle fracture of high-strength steels at very low temperatures

High-strength steels are used to increase the load carrying capacity of components. However, to guarantee a safe design, it is also necessary to combine high strength with adequate fracture toughness. In this paper, fracture toughness of three high-strength steels with yield strengths ranging from 460 to 890 MPa has been studied at very low temperatures. Taking into account experimental evidence, a new mechanism of cleavage at very low temperatures is proposed. This mechanism considers the possibility of reaching the ideal strength (the stress at which the lattice of a single crystal losses its stability) in the immediate vicinity of the fatigue crack tip. Moreover, a computational model able to calculate the external load needed to produce a catastrophic failure of these steels has been developed.