LinkingPark: An automatic semantic table interpretation system

In this paper, we present LinkingPark, an automatic semantic annotation system for tabular data to knowledge graph matching. LinkingPark is designed as a modular framework which can handle Cell-Entity Annotation (CEA), Column-Type Annotation (CTA), and Columns-Property Annotation (CPA) altogether. It is built upon our previous SemTab 2020 system, which won the 2nd prize among 28 different teams after four rounds of evaluations. Moreover, the system is unsupervised, stand-alone, and flexible for multilingual support. Its backend offers an efficient RESTful API for programmatic access, as well as an Excel Add-in for ease of use. Users can interact with LinkingPark in near real-time, further demonstrating its efficiency.     

不同段数爆破地震波的反应谱分析

为了研究段数对反应谱特性的影响,基于某石方控制爆破工程爆破振动实测数据,对不同段数爆破振动信号进行了反应谱分析。首先,利用实测的爆破振动速度信号采用直接微分法获得了加速度信号,并利用EEMD分解对加速度信号进行低通滤波去噪处理,获得了准确清晰的加速度曲线。然后,利用精确法求得了不同段数下爆破振动信号的速度反应谱和标准速度反应谱。分析结果表明:不同段数的爆破振动质点峰值速度与速度反应谱的峰值速度并不存在对应关系,因此分段数的选择应综合考虑结构对爆破振动的动态响应。     

Seismic behavior of geosynthetic-reinforced retaining walls backfilled with cohesive soil

This study investigates the seismic performance of geosynthetic-reinforced modular block retaining walls backfilled with cohesive, fine grained clay-sand soil mixture. Shaking table tests were performed for three ½ scaled (wall height 190 cm) and ¼ scaled model walls to investigate the effects of backfill type, the influence of reinforcement length and reinforcement stiffness effects. The El Centro and Kobe earthquake records of varying amplitudes were used as base acceleration. Displacement of the front wall, accelerations at different locations, strains on the reinforcements, and the visual observations of the facing and the backfill surface were used to evaluate the seismic performance of model walls. The model walls were subjected to rigorous shaking and the walls did not exhibit any stability problems or signs of impending failure. The maximum deformations observed on the models with cohesive backfill was less than half of the deformation of the sand model. The load transfers between the geogrid and cohesive soil was comparable to that of sand and hence the needed reinforcement length was similar as well. As a result; the model walls with cohesive backfills performed within acceptable limits under seismic loading conditions when compared with granular backfilled counterparts.     

A design of experiments investigation into dry separation using a Knelson Concentrator

Enhanced gravity, or centrifugal, separators have revolutionised gold processing over the past decades, significantly increasing the recovery of fine (−100 μm) free gold. One of the main drawbacks of centrifugal gravity concentrators is the large volume of water required (even if it is all recycled). With water becoming an ever increasingly important “commodity”, reducing this is of importance both from an environmental and a monetary point of view. This work investigated operating a laboratory scale Knelson Concentrator with a dry feed and using air as the fluidising medium. The feed used was a synthetic mixture of tungsten and quartz, used to mimic a gold ore. The response surface method and central composite design techniques were used to design the experiments and to model the results, with the experimental variables being the bowl speed (G-Level), air fluidising pressure and the feed rate. The models corresponded well to the experimental results, indicating that for this experimental setup, the optimal conditions were a bowl G-Level of 40 G, a feed rate of 220 g/min and an air fluidising pressure of 8 psi.     

Effect of select parameters on the properties of edible film from water-soluble fish proteins in surimi wash-water

Edible film from water-soluble fish proteins were developed by casting film solution on leveled trays and effects of pH (9.5, 10.0 and 10.5), heating temperature (60, 70 and 80 °C), and heating time (10, 20 and 30 min) of the film solution on various film properties were determined using Response Surface Methodology (RSM). The impact of pH and heating temperature of film solution was more significant, overall, on the film's properties than heating time. Contour plots of tensile strength and elongation at break was highest at pH of 10.0 at 70 °C (2.75-3.02 MPa) but low in elongation at break (6.35-9.16%), while water vapor permeability and oxygen permeability were at their lowest (58.55-65.96 g mm/m² d kPa and 351.33-624.18 cm³ μm/m² d kPa). There was a direct correlation between the films’ and proteins’ solubility on one hand, and heating temperature of film solution on the other, which reversed with change in pH of film solution. Film color was darker and more yellowish with increase in the pH of film solution.     

基于粗糙集信息观的决策表属性约简方法

粗糙集理论是近年来发展起来的一种有效的处理不精确、不确定、含糊信息的数学理论方法，它被广泛应用于相容和不相容决策表的属性约简和核属性计算。利用反例指出目前基于粗糙集信息观[2、6]的决策表属性约简和核属性计算方法的局限性。对决策表的性质作了深入的研究，研究发现文献[2、6]方法的不足原因是：它们没有考虑U／ind（C）中等价类的相客性。给出了基于U／ind（C）中等价类相客性的属性约简定义和核属性定义，并给出了一种新的基于粗糙集信息观的决策表属性约简和核属性计算方法。讨论了该方法同文献[2、6]方法的区别。最后用相同实例验证了该方法的有效性。     

基于属性相关表的关系模式全部候选关键字求法

本文提出了属性相关表这样一种新的概念，定义了相应的运算并研究了它的有关性质及定理，在此基础上提出了用属性相关表求关系模式全部主属性的等级，并给出了用主属性来组合关系模式全部候选关键字的算法，上述算法的时间复杂度均为Ｏ（ｎ＾２）。     

一种具有带孔补偿过滤器的γ剂量计的能响补偿计算

对在低能区有过高响应的γ辐射剂量计可采用带孔补偿过滤器进行能响补偿。本文介绍了对这类补偿过滤器选择最佳补偿参数(材料厚度和孔隙率)的近似求解方法;并对 CaSO:Tm 热释光剂量计用此方法作了实例计算。文中还计算了自制带有鼠笼结构的这类补偿过滤器的 CaSO:,Tm热释光剂量计对照射量的能量响应,与实测结果比较,各能量点响应的最大相差为10%。     

三维施工中SN388炮点表的设置

本文提供了SN388在三维施工中炮点表的几种设置方法，并进行了相应的对比说明，最后给出了改进炮点表设置的有关设想。     

Neural network systems to reproduce crash behavior of structural components

The use of neural networks as global approximation tool in crashworthiness problems is here investigated. Neural networks are not only asked to return some meaningful indices of the structural behavior but also to reproduce load-time curves during crash phenomena. To contain the number of examples required for the training process, parallel subsystems of small neural networks are designed. Design points for the training process are obtained by explicit finite element analyses performed by PAMCRASH. The settlement of the points in the design domain is defined using a maximum distance concept. The procedure is applied to different typical absorption structures made of aluminum alloy: riveted tubes, honeycomb structures, longitudinal keel beam and intersection elements of helicopter subfloors.