爆破工程费用计算方法探讨

爆破工程具有周期短、自成完整体系、技术管理严格的特点,但在费用管理上需进一步规范与整顿。本文阐述了工程费用的构成、调整及爆破工程费用的计算方法。     

Revisiting rock classification to estimate rock mass properties

This paper presents the results of ongoing research carried out by the author exploring methods to provide a more robust estimate of rock mass properties specifically for use in tunnel design. Data from various large-scale rock mass failures are introduced, including coal pillars. The damage-initiation,spalling-limit approach is compared to the coal pillar database. New comparisons of estimating the geological strength index(GSI) and relationships to estimate the Hoeke Brown failure criterion parameters, mb, s and a, are presented.     

Experimental study of crystal anisotropy based on ultra-precision cylindrical turning of single-crystal calcium fluoride

To realize ultimately efficient signal processing, it is necessary to replace electrical signal processing circuits with optical ones. The optical micro-resonator, which localizes light at a certain spot, is an essential component in optical signal processing. Single-crystal calcium fluoride (CaF₂) is the most suitable material for a highly efficient optical micro-resonator. The CaF₂ resonator can only be manufactured by ultra-precision machining processes, because its crystal anisotropy does not allow the application of chemical etching. However, the optical micro-resonator's performance depends definitely on the surface integrity.This study investigated the relationship between surface quality after ultra-precision machining and crystal anisotropy. Firstly, crack initiation was investigated on the (1 0 0), (1 1 0), and (1 1 1) planes using the micro-Vickers hardness test. Secondly, brittle-ductile transition was investigated by orthogonal cutting tests. Finally, cutting performance of cylindrical turning was evaluated, which could be a suitable method for manufacturing the CaF₂ resonator. The most difficult point in cylindrical turning of CaF₂ is that the crystalline plane and cutting direction vary continuously. In order to manufacture the CaF₂ optical micro-resonator more efficiently, analysis was conducted on crack initiation and surface quality of all crystallographic orientations from the perspective of slip system and cleavage.     

Effect of strain rate on the dynamic compressive mechanical behaviors of rock material subjected to high temperatures

Strain rate is not only an important measure to characterize the deformation property, but also an important parameter to analyze the dynamic mechanical properties of rock materials. In this paper, by using the SHPB test system improved with high temperature device, the dynamic compressive tests of sandstone at seven temperatures in the range of room temperature to 1000 °C and five impact velocities in the range of 11.0–15.0 m/s were conducted. Investigations were carried out on the influences of strain rate on dynamic compressive mechanical behaviors of sandstone. The results of the study indicate that the enhancement effects of strain rates on dynamic compressive strength, peak strain, energy absorption ratio of sandstone under high temperatures still exist. However, the increase ratios of dynamic compressive strength, peak strain, and energy absorption ratio of rock under high temperature compared to room temperature have no obvious strain rate effects. The temperatures at which the strain rates affect dynamic compressive strength and peak strain most, are 800, and 1000 °C, respectively. The temperatures at which the strain rates affect dynamic compressive strength and peak strain weakest, are 1000 °C, and room temperature, respectively. At 200 and 800 °C, the strain rate effect on energy absorption ratio are most significant, while at 1000 °C, it is weakest. There are no obvious strain rate effects on elastic modulus and increase ratio of elastic modulus under high temperatures. According to test results, the relationship formula of strain rate with high temperature and impact load was derived by internalizing fitting parameters. Compared with the strain rate effect at room temperature condition, essential differences have occurred in the strain rate effect of rock material under the influence of high temperature.     

冷轧平整机机前甩尾轧制工艺的开发与应用

本文介绍了柳钢冷轧板带厂1550 mm单机架平整机机前甩尾轧制的工艺。改进前轧制每卷钢卷生产效率低,钢卷成材率低,改进后生产效率、成材率明显提高,部分规格的钢卷能实现带尾剪切长度为零。     

Influences of chip serration on micro-topography of machined surface in high-speed cutting

Saw-tooth chip changes from macroscopically continuous ribbon to separated segments with the increase of cutting speed. The aim of this study is to find the correlations between chip morphology and machined surface micro-topography at different chip serration stages encountered in high speed cutting. High strength alloy steel AerMet100 was employed in orthogonal cutting experiments to obtain chips at different serration stages and corresponding machined surfaces. The chips and machined surfaces obtained were then examined with optical microscope (OM), scanning electron microscope (SEM), and white light interferometer (WLI). The result shows that chip serration causes micro-waves on machined surface, which increases machined surface roughness. However, wave amplitudes (surface roughness) at different serration stages are different. The principal factor influencing wave amplitude is the thickness of the sawed segment (tooth) of saw-tooth chip. With cutting parameters in this study, surface roughness contributed by chip serration ranges from 0.39 μm to 1.85 μm. This may bring on serious problems in the case of trying to replace grinding with high-speed cutting in rough machining. Some suggestions have been proposed to control the chip serration-caused surface roughness in high-speed cutting based on the results of the current study.     

Reasons for breaking of chemical bonds of gas molecules during movement of explosion products in cracks formed in rock mass

The purpose of this study was to develop a physico-mathematical model and technique for estimation of chemical bond stability depending on electric field intensity of an external point charge. A hypothesis for a possible physico-chemical mechanism of the formation of additional harmful gases in the rock destruction by blasting was proposed. The theoretical basis of the hypothesis is the method of theretical evaluation of bond energy depending on the distance to a point charge, the third Coulomb centre. The quantum-mechanical model for calculating the electronic terms of molecules makes it possible to solve problems associated with the determination of parameters of molecules under the action of various physical fields on the system under consideration. The model was approved for some diatomic molecules. The discrepancy between the experimental data and calculated data did not exceed 14%, which proves accuracy of the obtained results. The model can be used in the field of research into the causes of gas-dynamic phenomena in underground coal mines, in studies of the degree of stability of nanostructured components of coal under physical influences, and in the theoretical design of new compounds and structures in the field of nanomaterial science and nanotechnology.     

Formation and properties of high entropy oxides in Co-Cr-Fe-Mg-Mn-Ni-O system: Novel (Cr,Fe,Mg,Mn,Ni)3O4 and (Co,Cr,Fe,Mg,Mn)3O4 high entropy spinels

Possibility of formation of quinary and senary equimolar high entropy oxides from the Co-Cr-Fe-Mg-Mn-Ni-O system is presented. Different proposed compositions are synthesized using the solid-state reaction route at high temperatures (900−1100 °C) and quenched to room temperature. Phase composition of the samples is studied, showing tendency toward formation of two main phases: rock salt-structured Fm-3 m and spinel-structured Fd-3 m. It is documented that the annealing temperature has a profound effect on stability of both structures, and at 1100 °C usually the highest content of Fm-3 m phase is usually observed. Three different oxides, namely, (Co,Cr,Fe,Mn,Ni)₃O₄, (Co,Cr,Fe,Mg,Mn)₃O₄ and (Cr,Fe,Mg,Mn,Ni)₃O₄ are obtained as single-phase materials, which structure can be described as the high entropy Fd-3 m spinel one. The latter two compounds have not been previously reported in the literature. Activated character of the electrical conductivity dependence on temperature is observed, with relatively high total conductivity at high temperatures and corresponding high absolute values of Seebeck coefficient.     

机械-射流破岩耦合特性研究

在现代旋转钻井破碎井底岩石中仍是以机械破岩为主，理论与实践证明，射流辅助破岩是提高钻井破岩效率的重要途径，但它们的耦合特性研究极少。文章基于渗流场与应力场的耦合理论分析，进行了机械与射流破岩耦合特性的实验研究。结果表明：射流压力和水楔作用对岩石渗流场、应力场具有重要作用，耦合作用比非耦合作用的破岩效率有较大幅度的提高。在实验条件下，砂岩的耦合作用提高破岩效率40％左右，灰岩的耦合作用提高破岩效率20％左右。     

细节决定采输卤的成败

通过认真学习《细节决定成败》，结合井矿盐开采的实际，分别以生产过程中的三个细节为主，讨论了在采输卤生产技术控制中的细节的重要性。