垦71井区三维VSP资料波场分离方法应用研究

三维VSP资料是多偏移距VSP资料，资料中多种类型的波叠合在一起形成复杂波场。从复杂波场中分离出单一的保幅反射波波场是三维VSP波场分离的重要工作。常规二维VSP波场处理方法单一，难以适用于复杂的三维波场处理。针对三维VSP资料的波场特点，以分离上行反射P波为例，将单一波场分离方法加以适当组合，对垦71井区三维VSP实际资料进行了应用研究。结果表明，波场分离处理中叠加消去法和中值滤波相结合以及F—K滤波和中值滤波相结合的方法克服了单一方法的缺陷，波场处理后获得了波组特征明显、波场清晰单一的上行反射P波保幅波场，取得了较好的波场分离效果。     

Cu基络合物催化甲醇液相氧化羰化反应

针对甲醇液相氧化羰基化法合成碳酸二甲酯(DMC)工艺,开发了新型Cu基络合催化剂(CuB rnLm)。对CuB rnLm催化剂的活性及其稳定性进行了研究。实验结果表明,采用该催化剂,甲醇转化率和DMC选择性较高;元素价态和物质结构分析表明,CuB rnLm催化剂循环使用5次后仍保持较好的稳定性。采用正交设计和中心响应曲面法设计实验,并使用S tatistica软件进行统计分析,寻求出反应的主要影响因素,并得到优化的工艺条件:反应温度100~110℃、反应压力3.0~3.5M Pa、反应时间4~6h、CuB rnLm催化剂质量浓度(以甲醇的体积计)0.15~0.20g/mL。在此工艺条件下,甲醇转化率可达23%以上,DMC的选择性为96%~98%。     

求解二维结构-声耦合问题的一种直接方法

本文基于传递矩阵法(TMM)和虚拟边界元法(VBEM)，提出了一种求解在谐激励作用下二维结构-声耦合问题的直接法。文中对任意形状的二维弹性环建立了一阶非齐次运动微分方程组，便于用齐次扩容精细积分法求解，对于含有任意形状孔穴的无穷域流体介质的Helmholtz外问题，采用复数形式的Burton-Miller型组合层势法建立了虚拟边界元方程，保证了声压在全波数域内存在唯一解。根据叠加原理并结合最小二乘法，提出了一种耦合方程的直接解法，由于该方法不存在迭代过程，因而具有较高的计算精度和效率。文中给出了二个典型弹性环在集中谐激励力作用下声辐射算例，计算结果表明本文方法较通常采用的混合FE／BE法更为有效。     

WC/Cu复合材料制备及其高温性能

用机械合金化法结合冷变形，制备了WC／Cu复合材料，研究了冷变形后复合材料的组织特征和高温退火时韵性能变化。结果表明：烧结后的材料经冷变形，组织呈显著纤维状，WC颗粒弥散分布，密度明显提高，达到理论密度的99．2％；复合材料经600～900℃高温退火，强度和硬度略有下降，塑性则有大幅提高；900℃退火时未发生明显的再结晶，界面结合良好；所制备的WC／Cu复合材料有优良的综合性能。     

Polystyrene‐supported polyoxyethylene bound potassium permanganate as a heterogeneous oxidizing agent

Oxidation behavior of a 2 mol % divinylbenzene (DVB)‐crosslinked polystyrene‐supported permanganate function was investigated toward low molecular weight primary and secondary alcohols and aldehydes. The permanganate function was attached to a polystyrene support through cyclic polyoxyethylene (POE) units immobilized on the support. Contrary to the oxidations catalyzed by low molecular weight permanganate reagents, the oxidation of primary alcohol terminated in the aldehyde stage. The secondary alcohols were converted to the respective ketone and aldehyde to acid. The effect of the variable parameters similar to solvent, temperature, and reagent to substrate ratio was followed. Nonpolar cyclohexane was found to be the best solvent for the present study. Also the reactivity increased with increasing temperature. The oxidizing reagent possesses a long shelf life and could be recycled several times without reduction of capacity and mechanical stability. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3708–3717, 2003     

化学复合镀层激光处理研究

研究了激光处理对Ni-P -SiC化学复合镀层的影响。借助于扫描电镜、能谱仪、X射线衍射、显微硬度计等设备对激光处理后复合镀层的表面形貌、组织结构及性能进行了综合分析。结果表明 ,对复合镀层进行激光处理可以获得与炉内加热同样的镀层硬度 ,且当激光功率 4 0 0W ,扫描速度 1.5m /min时 ,镀层硬度高于炉内加热的硬度     

大型往复式压缩机的配管设计

大型往复式压缩机功率大、占地面积大,管道振动问题也更为突出。笔者结合实践经验,对大型往复式压缩机的配管设计进行探讨,说明了平面布置与管道防振设计的密切关系,并介绍了管道防振设计的方法和步骤,以及相对简单的复杂管系气柱固有频率的转移矩阵计算方法。     

Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

T8钢－聚有机硅氧烷仿生减粘降阻复合涂层的特性

研究了Ｔ８钢－聚有机硅氧烷仿生减粘降阻复合涂层的表面润湿性、磨料磨损特性及对土壤的减粘降阻性能与金属材料相比，仿生复合涂层的表面憎水性显著提高，水在其表面上的接触角达９２°；与４５钢相比，其磨料磨损的体积相对耐磨系数为６３％，降阻率达１５．２２％～２２．２７％