Double emulsion (W/O/W) gel stabilised by polyglycerol polyricinoleate and calcium caseinate as mangiferin carrier: insights on formulation and stability properties

Mangiferin (MGF) is a phenolic compound isolated from mango, but its poor solubility significantly limits its use. In this study, MGF was embedded into the inner aqueous phase of W₁/O/W₂ emulsions. Firstly, the dissolution method of MGF was determined. MGF remained stable in solution with pH 13 at 30 min, and its solubility reached 10 mg mL⁻¹. When the pH of MGF solutions was adjusted from pH 13 to pH 6, MGF did not immediately crystallise, providing sufficient time to construct the MGF-loaded W₁/O/W₂ emulsions. Subsequently, the MGF-loaded W₁/O/W₂ emulsions were constructed using polyglycerol polyricinoleate (PGPR) and calcium caseinate (CAS). The formation and stability of the W₁/O/W₂ emulsions were investigated. The MGF-loaded W₁/O/W₂ emulsions stabilised with 1% PGPR and 1% – 3% CAS exhibited a low viscosity, limited loading capacity, and poor stability. Conversely, the MGF-loaded W₁/O/W₂ emulsions stabilised by 3%PGPR–3%CAS exhibited optimal loading capacity (encapsulation efficiency = 95.31% and loading efficiency = 0.91%) and stability, which was attributed to the fact that high viscosity and gel state retarded the migration of inner aqueous phase. These results indicated that the W₁/O/W₂ emulsions stabilised by PGPR and CAS may be a potential alternative for encapsulating mangiferin.     

LTE系统多小区上行联合功控算法

针对传统的小区内开环功率控制算法通常以提升本小区的吞吐量性能为目标，忽略了当前小区用户对邻小区用户同频干扰的问题，为提升边缘用户性能的同时兼顾系统整体性能，提出了一种LTE系统小区间上行联合功率控制（UJPC）算法。该算法采用单基站三扇区为系统模型，以最优化系统吞吐量比例公平函数为目标，首先根据最小信干噪比（SINR）约束值和用户最大发射功率这两个约束条件得到相应的数学优化模型，然后采用连续凸近似的方法求解优化问题得出各个基站所管辖的小区内所有用户的最优发射功率。仿真结果表明，与基准的开环功控方案相比，联合功控方案在保证系统平均频谱利用率的情况下能够较大幅度地提高小区边缘频谱利用率，其最佳性能增益能达到50%。     

新型毫米波微带带通滤波器

介绍了一种新型的加载电容型毫米波微带带通滤波器。对这种滤波器进行了分析,推导出了滤波器中所用谐振单元间的耦合系数。该滤波器通过加载电容而出现慢波效应,使得在不改变电路性能的情况下,减小了电路尺寸。同时由于电路中加载电容形成的慢波效应而出现了带阻效应,因此对谐波有很好的抑制作用。利用高频分析软件CST仿真分析并设计了这种新型的加载电容型毫米波微带带通滤波器,实验结果与设计曲线结果相符。     

An experimental study on the pumping performance of molecular drag pumps

The pumping performance of molecular drag pumps (MDP) has been investigated experimentally. The experimented MDPs are a disk-type drag pump (DTDP), helical-type drag pump (HTDP) and compound drag pump (CDP), respectively. In the case of the DTDP, spiral channels of a rotor are cut on both upper surface and lower surface of a rotating disk, and the corresponding stator is a planar disk. In the case of the HTDP, the rotor has six rectangular grooves. The CDP consists with the DTDP, at lower part, and with the HTDP, at upper part. The experiments are performed in the outlet pressure range of 0.2–533 Pa. The inlet pressure and compression ratio are measured under the various conditions of outlet pressure and throughputs, and nitrogen is used for the test gas. At the outlet pressure of 0.2 Pa, the ultimate pressure has been reached to 1.0 × 10⁻² Pa for the HTDP, 1.3 × 10⁻⁴ Pa for the DTDP, and 3.6 × 10⁻⁵ Pa for the CDP. The maximum compression ratio of the CDP is much higher than those of the DTDP or HTDP. Consequently, the ultimate pressure of the CDP is the lowest one.     

An investigation of the unstable region for dense phase conveying in sliding bed flow

For fine powdered materials, capable of being conveyed in dense phase, a conveying region exists in which instability in flow and pipeline blockage can occur if the pressure gradient available is insufficient to maintain a minimum value of solids loading ratio. A reduction in material flow rate can also lead to pipeline blockage in this region. Conveying trials under-taken with cement are used to illustrate the nature of the problem.     

用扫描电镜判断火工药剂与金属桥丝长期接触的相容性

火工药剂与金属桥丝接触，在高温、高湿条件下贮存一定时间后两者是否相容，用电镜观察其金属表面的腐蚀形态（面积、深浅），以此来判断金属桥丝与火工药剂的相容性。     

乳化炸药混装车水孔爆破的优越性

该文分析了应用袋装炸药装填水孔爆破产生拒爆、"冲天炮"、根底偏高和爆破效果差等问题,然而应用乳化炸药混装车装填水孔可以解决这些问题,并且爆破后具有根底平整、大块率低、毒气少和综合效益高等优点.以三峡永久船闸旁侧泄水箱涵工程和江苏田湾核电站工程为例进行了分析.     

Paste Residence Time in a Spouted Bed Dryer. III: Effect of Paste Properties and Quality Interactions

The aim of this study was to evaluate the effects of paste properties on residence time during drying in a spouted bed dryer with inert bodies. The effect of paste solids content, surface tension, and viscosity on the residence time distribution and the mean residence times were studied using factorial experimental designs. The inert bodies used were glass and polyethylene beads. The mean residence times varied from 13.6 to 16.3 and 12.2 to 17.7 min for drying on glass and polyethylene beads, respectively. The analysis of variance showed that mean residence times significantly depended on solids content and surface tension for glass beads and also on viscosity for polyethylene beads. The residence time distributions for all conditions studied fitted well to the perfect mixing cell when applying the continuous stirred vessels in series model analysis. The powder density, flowability, and particle size depended on paste properties and inert type.