Interpolating Quintic Polynomial with C~1 Continuity

A method constructinq C~1 Piecewise quintic polynomial over a triangular grid to interpo-late function values and partial derivatives at vertices is presented in this paper.The set of precise poly-nomials of this method is discussed.     

Effects of Surface Concentration on Drying Behavior of Carbohydrate Solutions

As the surface properties of the drying materials are very important not only for the drying rate but also for the quality change during drying, the effects of surface concentration on the drying behavior of liquid foods (sugar solutions) were investigated by isothermal drying experiments and by numerical calculation experiments. The isothermal drying experiments with gelled sugar solution systems (sucrose and maltodextrin) were carried out at various relative humidity (RH) values (RH = 0 to 84%). Separate experiments were carried out for determination of the desorption isotherms.

The isothermal drying curves of sugar solutions at RH = 0 to 51% were very similar. Numerical simulations also showed that the drying curves of these sugars at the surface concentration = 0 and 0.1 are almost the same, although the concentration distributions are different.

When a small amount of gelatin was added to sugar solutions, the drying rate decreased remarkably as the gelatin might form a thin film (skin) near the surface, and consequently the retention of ethanol increased.     

Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.     

Stability of hydrogenated nanodiamonds under extreme ultraviolet irradiation

It is generally accepted that diamond is resistant to a wide spectrum of electromagnetic radiation from the ultraviolet through to the soft X-ray range, which makes it very attractive for the fabrication of diamond-based photodetectors. However the effect of photon radiation on the diamond structure has not yet been examined. In the work presented here, photoelectron spectroscopy has been used to study the graphitization of nanodiamond crystallites exposed to extreme ultraviolet radiation. Under such irradiation, the surface hydrogen groups and graphite species are found to prevent graphitization. The mechanism of radiation-induced nanodiamond graphitization is discussed.     

Preparation of CeO2-ZrO2 mixed oxide with high surface area and high thermal stability

Ceria-zirconia solid particles have been recognized as a key material of the automotive exhaust catalysts since they can release and uptake oxygen owing to the rapid reversible oxidation states of cerium between Ce³⁺ and Ce⁴⁺. Several methods have recently been described to prepare the CeO₂-ZrO₂ solid particles used in the catalysts. In this paper, a new coprecipitation method is used to prepare the CeO₂-ZrO₂ solid particles. The Ce-Zr alcogel is dried and calcined in flowing N₂ not in flowing air under atmospheric pressure. The results show that the ceria-zirconia sample calcined at 650 °C has high surface area over 90 m²g⁻¹, which drops to 40 m²g⁻¹ following treatment at 900°C.     

Applications of the discrete element method in mechanical engineering

Compared to other fields of engineering, in mechanical engineering, the Discrete Element Method (DEM) is not yet a well known method. Nevertheless, there is a variety of simulation problems where the method has obvious advantages due to its meshless nature. For problems where several free bodies can collide and break after having been largely deformed, the DEM is the method of choice. Neighborhood search and collision detection between bodies as well as the separation of large solids into smaller particles are naturally incorporated in the method. The main DEM algorithm consists of a relatively simple loop that basically contains the three substeps contact detection, force computation and integration. However, there exists a large variety of different algorithms to choose the substeps to compose the optimal method for a given problem. In this contribution, we describe the dynamics of particle systems together with appropriate numerical integration schemes and give an overview over different types of particle interactions that can be composed to adapt the method to fit to a given simulation problem. Surface triangulations are used to model complicated, non-convex bodies in contact with particle systems. The capabilities of the method are finally demonstrated by means of application examples. Commemorative Contribution.     

Characterization and modification of fillers for paints and coatings

This paper highlights the possibility of inverse gas chromatography for the surface characterization of common fillers (CaCO₃, talc, SiO₂,) for paints and coatings. Divided solids are described, on the one hand, by the dispersive component of their surface energy and, on the other, by a specific parameter indicating their acid-base interaction potential. The role of the surface morphology at a molecular level is also examined. It is demonstrated that steric effects play an important role in the adsorption of probes on lamellar solids like talc. The consequences of surface treatments as well as examples of practical applications are also reported.     

Micro-RBS characterisation of the chemical composition and particulate deposition on pulsed laser deposited Si1−xGex thin films

The formation and deposition of particulates by pulsed laser deposition of Si_1−xGe_x semiconductor alloy thin films are discussed. Using Rutherford backscattering spectrometry with micrometer lateral resolution (micro-RBS) the film composition was measured with high accuracy, even in the presence of particulates with a high areal density of 20,000–30,000 particulates per mm². We show that on impact of a particulate, the part of the thin film which is already deposited probably melts and its Ge content segregates to the surface.     

Effect of the Treatment Temperature on the Surface Drying Set of Sugi Boxed-Heart Square Timber

High-temperature and controlled humidity treatment before drying has proven to be highly effective in preventing surface checks by forming drying sets in the surface layer of boxed-heart square timber in Japan. In this study, we examined the differences of the surface drying sets on sugi timber under different treatment temperatures. As a result, the width of a surface check after drying was much smaller at a treatment temperature of 120°C than at 80°C, and this indicates that the drying set with 120°C treatment would be larger than that with 80°C treatment. Also we observed that treatment temperature had a greater effect on the drying set as the drying advanced.