Process and joint quality of ultrasonic vibration enhanced friction stir lap welding

In order to improve the process effectiveness and joint quality, ultrasonic vibrations were integrated with friction stir lap welding. Effect of ultrasonic exertion on the process and joint quality of AA 6061-T6 were investigated. Upon ultrasonic exertion, joints owned larger effective lap width, shorter hooks and improved strength. Weld fracture mode changed from a ductile–brittle mixed mode to a more ductile mode while the fracture path shifted from lap interface to beyond the stir zone. Material flow and interface defects were characterised using lap welded dissimilar aluminium alloy joints. Ultrasonic vibration improved the material flow and reduced the interfacial defects. Variations in failure load of joints were found in accordance with the variations in material flow and interfacial defects.     

高导电性原油电脱盐工艺研究

南阳原油中金属含量较高,掺有部分3次采油采出原油,加工时易造成电脱盐装置原油乳化,电导率高,脱盐难度较大。装置投产十几年来脱后含盐一直不合格,经过改造仍然超标,常压塔顶腐蚀严重。为此,对原油进行了电脱盐工艺条件及破乳剂研究,研制出了高效电脱盐设备和生物复合脱盐剂及降电流剂,采用平流弓形电极进行改造,解决了该原油的电脱盐问题,使脱后含盐达到3 mg/L。     

超声波车辆车轴探头的研制与应用

提出了一种用于检测在役车辆车轴产生疲劳裂纹的超声波方法,设计了中心孔探头与斜角探头一起,完成了对车辆车轴的关键区域探伤。     

碳素材料超声检测的信号处理方法

针对碳素材料超声无损检测存在信噪比较低的问题,从自相关性出发分析了典型超声检测信号的组成成分,提出了在自相关分析的基础上的小波去噪思想,探讨了自相关分析和小波分析相结合的信号处理方法。利用此方法进行实际超声信号分析效果良好。     

Non-contact handling in microassembly: Acoustical levitation

Microassembly is currently of the utmost importance in industry. Nevertheless, the classical assembly processes are no longer usable for very small components, typically ranging from 10  m to 10 mm, since usually neglected surface forces disturb the handling task by inducing adhesion between the component and the gripper. A promising alternative to tackle surface forces consists in levitating the handled component. The various advantages of this contactless handling method are reviewed here and justify the choice of this approach. Consequently, the numerous physical principles suitable for contactless handling are briefly described together with their limitations. The evaluation shows that acoustic levitation is best fitted in the case of microassembly. A classification of literature applications is presented hereafter with special focus on acoustic levitation. Finally, the most common models of acoustical levitation are inspected in a general way. The described models come within the scope of non-linear acoustics.     

在建坝体中部分浆砌石的控制爆破拆除

某在建大坝部分浆砌石坝体因质量不合格须爆破拆除。保护余留坝体免受爆破影响是此工程的重点,为此,采用了小直径浅孔和微差爆破分层拆除方法,被拆除部分和被保护部分之间预留保护层。爆破施工过程中,利用超声波观测法和压水试验法判断被保护坝体是否受到了爆破震动的影响。根据判断结果,调整爆破参数,以减小爆破震动。文中论述了爆破参数的选择、保护层厚度的确定,同时介绍了安全控制技术、测点布置以及监测结果。     

Accurate estimation of environment parameters from ultrasonic data

This paper describes a robust and accurate ultrasonic sensing system for a mobile robot. The system continuously updates a local map of the environment in which obstacles are represented by straight lines or points in a robot centered coordinate frame. The presented algorithms use a Kalman filter for the reduction of the noise in the ultrasonic data and use a systematical error correction (‘bundle correction’) to reduce the uncertainty in obstacle direction. Experiments are carried out in simulation and with a real mobile robot system. Results show that the accuracy with which line parameters can be estimated is in the order of 1 degree for the orientation and about 2 cm for the position. The effect of the bundle correction is significant and maximal when the robot approaches walls under a small angle.     

超声波对化学镀Ni－Cr－P非晶态薄膜的金刚石性能的影响

研究了超声波对化学镀Ｎｉ－Ｃｒ－Ｐ非晶态薄膜的金刚石性能的影响。结果表明，超声波可使金刚石表面非晶态薄膜更加均匀和致密，从而提高了抗压强度，氧化温度和晶化后的强度。随超声波频率的增加，金刚石性能有增加的趋势。     

Evolution of the capillary network in a reactive powder concrete during hydration process

Ultrasonic waves in echographic mode, combined with autogenous shrinkage measurements, were used to study the evolution of the capillary network of reactive powder concrete (RPC) from the time after the mixing. Two characteristic porous classes have been identified: the first, between 10 and 20 nm, begins when the material reaches its solid hyperstatic state, and the second about 1 or 2 nm. The first class is associated with the porous space between the C-S-H hydrate clusters and the second with the internal porosity of the hydrate. The evolution of the active capillary radius as a function of the degree of hydration allows us to understand the strong interaction between the capillary network size and the chemical activity given by the dissipated calorimetric power curve. Indeed, the maximum point of the chemical activity marks the transition of the first class of pores to the second one. Finally, measurements of electrical conductivity through RPC samples show that after the maximum of the dissipated power, the curve of this electrical conductivity presents the same evolution as the capillary radius. As the electrical conductivity clearly depends on the evolution of the capillary network, the similarity between the results confirms our analysis in pore classes.     

圆锥破碎机躯体裂纹的超声波探伤

重点介绍了圆锥破碎机躯体裂纹的超声波检测及缺陷判定的方法,为矿山其它大型设备的裂纹检测提供了经验。