基于信号增强的缓慢泄漏检测方法

目前管道泄漏检测方法可有效检测突发泄漏，对于缓慢泄漏则存在检测灵敏度低、定位不准确等问题。基于此，提出了一种基于信号增强的缓慢泄漏检测方法。通过信号压缩（抽取及移位）克服缓慢泄漏压力信号下降平缓的缺点；根据声波信号具有波形尖锐突出、对突发泄漏敏感的优点，通过建立以压力为输入、虚拟声波为输出的声波信号变送器模型，将压力信号转换为声波信号，克服了泄漏压力信号容易被淹没在管道压力波动及背景噪声中的缺点，实现了缓慢泄漏信号的增强；利用临近插值方法重构虚拟声波信号，基于延时互相关分析实现了缓慢泄漏的准确定位。实验结果表明，该方法具有显著的信号增强效果和定位精度，实现了缓慢泄漏的准确检测。     

混凝土结构的压电声波检测分析

本文介绍了混凝土结构的压电体波和表面波检测的主要进展,对两种压电声波检测的优缺点进行了总结。体波检测设备一般埋入混凝土内部,需要选择合理的检测部位,检测结果较为精确;声表面波检测无需选择特定的部位,但是检测深度有限。在实际检测工作过程中,可以联合两种方法相互验证。     

求解二维结构-声耦合问题的一种直接方法

本文基于传递矩阵法(TMM)和虚拟边界元法(VBEM)，提出了一种求解在谐激励作用下二维结构-声耦合问题的直接法。文中对任意形状的二维弹性环建立了一阶非齐次运动微分方程组，便于用齐次扩容精细积分法求解，对于含有任意形状孔穴的无穷域流体介质的Helmholtz外问题，采用复数形式的Burton-Miller型组合层势法建立了虚拟边界元方程，保证了声压在全波数域内存在唯一解。根据叠加原理并结合最小二乘法，提出了一种耦合方程的直接解法，由于该方法不存在迭代过程，因而具有较高的计算精度和效率。文中给出了二个典型弹性环在集中谐激励力作用下声辐射算例，计算结果表明本文方法较通常采用的混合FE／BE法更为有效。     

复合材料手动扫描超声特征成像检测

研究了复合材料手动扫描超声特征成像检测，通过对超声检测信号的全波列采集与处理，实现了A，B，C扫描成像；相位特征成像；当量特征成像；超声层析技术和超声频谱分析技术。该系统已经在复合材料的检测上得到了良好的应用。     

Low temperature delamination of plastic encapsulated microcircuits

Plastic encapsulated microcircuits (PEMs) are increasingly being used in applications requiring operation at temperatures lower than the manufacturer’s recommended minimum temperature, which is 0°C for commercial grade components and −40°C for industrial and automotive grade components. To characterize the susceptibility of PEMs to delamination at these extreme low temperatures, packages with different geometries, encapsulated in both biphenyl and novolac molding compounds, were subjected to up to 500 thermal cycles with minimum temperatures in the range −40 to −65°C in both the moisture saturated and baked conditions. Scanning acoustic microscopy revealed there was a negligible increase in delamination at the die-to-encapsulant interface after thermal cycling for the 84 lead PQFPs encapsulated in novolac and for both 84 lead PQFPs and 14 lead PDIPs encapsulated in biphenyl molding compound. Only the 14 lead novolac PDIPs exhibited increased delamination. Moisture exposure had a significant effect on the creation of additional delamination.     

Growth Stresses in the Oxide Scales on TiAl Alloys at 800 and 900°C

In the oxidation of TiAl alloys, the role of scale-growth stresses formed during oxidation has, thus far, been unknown. In the present paper the oxide-growth stresses were investigated by the deflection-test method in monofacial oxidation (DTMO) accompanied by acoustic-emission measurements. On unmodified surfaces the growth stresses are compressive and reach levels of around –100 MPa. At the same time, significant acoustic emission occurs indicating that even under isothermal conditions, stresses are relieved by a scale-cracking mechanism. For oxide scales on TiAl surfaces, which had been ion implanted with chlorine before oxidation, a very thin protective alumina layer is formed which, however, develops growth stresses in the range of several GPa, accompanied by intensive acoustic emission. In all stress–time curves, a dynamic situation is observed. This consists of phases of stress relief by scale microcracking and phases of stresses increase due to crack healing and further oxide growth. As a result, the level of stress as a function of oxidation time, is characterized by an oscillating course.     

Acoustic emission method for research and control of friction pairs

One of the new physical methods that provides much information about the processes going on in a friction contact zone in real time is acoustic emission (AE). Basic experimental results of AE in friction are presented and analysed. Using AE signals we can get an indication about the state of the friction processes, about the quality of solid and liquid layers on the contacting surfaces in real time, sometimes about intensity of wear, changing of wear and friction regimes and so on. The influence of sliding velocity, load, roughness and some physical and mechanical properties of the body on the parameters of AE are also given. Some attention to the practical implementation of these techniques for control of capability for work of friction pairs in real conditions are given. Modern methods and devices enable condition monitoring of sliding and rolling bearings.     

基于ANN的声目标识别系统及其DSP实时实现

介绍了一种基于人工神经网络(ANN)的声目标识别系统,概述了用MATLAB专用工具箱对神经网络权值进行训练及仿真的过程,叙述了ANN目标识别系统的数字信号处理器(DSP)实时实现过程,并着重分析定点实现过程中程序变量的定标、非线性运算的实现、溢出的处理等关键步骤.对不同字长的识别结果进行比较表明,基于定点实时实现的系统数据保持很高的精度,可以得到与浮点处理相同的识别率.     

套管固井质量问题及对策分析

从油田现场反应的情况出发，对调整井固井，尾管固井，大位移井套管固井和其他固井的质量问题进行了分析，针对各种问题产生的原因，提出了相应换解决办法。