Development and validation of a micro-fin tubes evaporator model using R134a and R1234yf as working fluids

This paper presents a model of shell and tube evaporator with micro-fin tubes using R1234yf and R134a. The model developed for this evaporator uses the ε-NTU method to predict the evaporating pressure, the refrigerant outlet enthalpy and the outlet temperature of the secondary fluid. The model accuracy is evaluated using different two-phase flow boiling correlations for micro-fin tubes and comparing predicted and experimental data. The experimental tests were carried out for a wide range of operating conditions using R134a and R1234yf as working fluids. The predicted parameter with maximum deviations, between the predicted and experimental data, is the evaporating pressure. The correlation of Akhavan– Behabadi et al. was used to predict flow boiling heat transfer, with an error on cooling capacity prediction below 5%. Simulations, carried out with this validated model, show that the overall heat transfer coefficient of R1234yf has a maximum decrease of 10% compared with R134a.     

Eine Definitionssprache für die Kommunikationsverbindungen in verteilten Automatisierungssystemen

Eingegangen am 13.11.1996, in überarbeiteter Form am 12.5.1997     

重金属(以铅计)含量测定方法的改进

探讨了用硫化钠-丙三醇溶液代替饱和硫化氢水溶液进行重金属(以铅计)测定的分析方法。此法简单、快速,并在实际应用中取得了满意的结果。     

Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

Eine Produktions-/Lagerhaltungspolitik bei stochastischer Nachfrage im Mehrproduktfall

Zusammenfassung Eine Lagerzielmengenpolitik für den Fall intermittierender Fertigung mehrerer Sorten auf einer Anlage bei stochastischer Nachfrage wird durch ein Warteschlangenmodell abgebildet. Für die sich ergebenden Kostenfunktion wird eine Approximation vorgeschlagen. Die Bestimmung optimaler Losgrößen und Lagerzielmengen wird untersucht.     

Advancements in the design and validation of an air pollution integrated assessment model for Spain

This paper describes the design and application of the Atmospheric Evaluation and Research Integrated model for Spain (AERIS). Currently, AERIS can provide concentration profiles of NO₂, O₃, SO₂, NH₃, PM, as a response to emission variations of relevant sectors in Spain. Results are calculated using transfer matrices based on an air quality modelling system (AQMS) composed by the WRF (meteorology), SMOKE (emissions) and CMAQ (atmospheric-chemical processes) models. The AERIS outputs were statistically tested against the conventional AQMS and observations, revealing a good agreement in both cases. At the moment, integrated assessment in AERIS focuses only on the link between emissions and concentrations. The quantification of deposition, impacts (health, ecosystems) and costs will be introduced in the future. In conclusion, the main asset of AERIS is its accuracy in predicting air quality outcomes for different scenarios through a simple yet robust modelling framework, avoiding complex programming and long computing times.     

Abstimmung von Produktions- und Transportlosgrößen zwischen Zulieferer und Produzent

Es wird eine Erweiterung des mehrstufigen stationären Losgrößenproblems mit endlichen Produktionsgeschwindigkeiten um den zeitpunktgeballten Transportvorgang vorgestellt. Diese Darstellung gibt die Beziehungen zwischen Zulieferer, Transporteur und Produzent adäquat wieder. Hinsichtlich der Abstimmung der Entscheidungsgrößen dieser organisatorischen Einheiten wird zwischen einer rein simultanen, einer rein sukzessiven sowie zweier gemischt simultan-sukzessiver Koordinationsarten unterschieden. An Hand einer analytischen Untersuchung werden Unterschiede und Gemeinsamkeiten der jeweiligen Entscheidungsgrößen und der daraus resultierenden Kostenfunktionen dargestellt. Schließlich zeigt eine numerische Analyse die Gesamtkostenunterschiede zwischen der rein simultanen und rein sukzessiven Koordinationsart auf.An extension is introduced to the multi-stage stationary lot-sizing problem with finite production rates by the time-concentrated transportation-process. This representation adequately demonstrates the relations between supplier, carrier and producer. With regard to the reconciliation of the decision variables of these institutional units one differentiates between a pure simultaneous, a pure gradual and two mixed simultaneous-gradual coordination methods. The differences and correspondences of the respective decision variables and the resulting cost functions are demonstrated by means of an analytical examination. Finally, a numerical analysis shows the distinctions in total cost between the pure simultaneous and pure gradual coordination method.     

Espaces métriques rationnellement présentés et complexité, le cas de l'espace des fonctions réelles uniformément continues sur un intervalle compact

We define the notion of rational presentation of a complete metric space, in order to study metric spaces from the algorithmic complexity point of view. In this setting, we study some representations of the space C[0,1] of uniformly continuous real functions over [0,1] with the usual norm: ||f||_∞ = Sup{|f(x)|; 0x1}. This allows us to have a comparison of global kind between complexity notions attached to these presentations. In particular, we get a generalization of Hoover's results concerning the Weierstrass approximation theorem in polynomial time. We get also a generalization of previous results on analytic functions which are computable in polynomial time.     

“任务驱动”模式下高职精细化工课程的教学实践

针对高职学生的基础知识薄弱和学习能动性较低等特点,从高职院校人才培养实际情况和教学改革入手,依据建构主义学习理论,采用"任务驱动"课堂教学模式,笔者经过三年《精细化工》课程教学实践磨砺,摸索出较系统完整的"三步驱动教学法",即通过"任务驱动"、"轮值主持"和"即时考核"三步骤的驱动教学,极大地激发了学生自主学习的能动性,该模式的教学过程使课堂充满生机和活力,产生了积极良好的教学效果。"任务驱动"课堂教学模式,不仅需要教师备好课,还要时时把握学生的心理和学习进展,这对教师的专业知识掌握程度、教学业务能力、课堂组织能力、专业实践能力等提出了更高的要求。