热流体喷射变形机理与喷嘴结构

高速短程纺技术能生产三维卷曲短纤维,该技术的关键之一是热流体喷射装置。本文介绍了热流体喷射装置的演变与特点及它的加工机理和某些已应用的实际装置。     

Q195冷轧板材轧制困难原因分析

针对部分Q195冷轧板材存在轧制困难的现象，进行了现场检验与分析。带状组织、混晶现象严重导致变形强化系数偏高是造成轧制困难的主要原因。     

利用热管纺丝技术一步法生产FCY

利用平板型热管纺丝装置对普通高速纺丝机进行技术改造，并一步法生产出充分结晶的ＰＥＴ纤维（ＦＣＹ）。该纤维可直接用于织造，调节热管温度、热管安装位置可获得满足后道工序不同需要的ＦＣＹ。     

用LG55冷轧管机轧制小直径不锈钢管孔型改进

介绍了ＬＧ５５冷轧管机使用Φ７～３２ｍｍ、Φ５０～３２ｍｍ孔型轧制小直径不锈钢管的工艺特点。试验表明，两种孔型可行，且Φ５７～３２ｍｍ孔型的综合使用效果更好。     

Effect of deposition conditions on the properties and annealing behavior of cold-sprayed copper

The deposition of copper by cold gas dynamic spraying has attracted much interest in recent years due to the capability to deposit low-porosity oxide-free coatings. However, it is generally found that as-deposited copper has a signicantly greater hardness, and potentially lower ductility, than bulk material. In this article, copper was deposited by cold spraying using helium as the driving gas at both 298 and 523 K. Evidence is presented indicating that the material sprayed at the lower temperature exhibits a lower dislocation density throughout the grain structure than the material sprayed at the higher temperature. The low stacking fault energy of copper restricts recovery during annealing, and thus microstructural changes during annealing only proceed once recrystallization begins. The material sprayed at low temperature (with the low dislocation density) exhibited recrystallization at annealing temperatures as low as 373 K with a corresponding reduction in hardness. However, the copper sprayed with helium at 523 K was resistant to annealing at temperatures up to 473 K where the dislocations in the structure prevented recrystallization. However, at higher temperatures, recrystallization did proceed (with corresponding reductions in hardness). The fracture behavior of the copper that was cold sprayed with helium at 523 K, both in the as-sprayed condition and following annealing, was measured and explained in terms of the annealing mechanisms proposed. The original version of this paper was published in the CD ROM Thermal Spray Connects: Explore Its Surfacing Potential, International Thermal Spray Conference, sponsored by DVS, ASM International, and HW International Institute of Welding, Basel, Switzerland, May 2–4, 2005, DVS-Verlag GmbH, Düsseldorf, Germany.     

三箱式纺丝技术生产PET/PA6复合纤维

介绍了采用三箱式纺丝技术生产PET/PA6复合纤维的设备及工艺。重点对纺丝箱体、纺丝温度控制进行了详细的讨论。     

High resolution solid state 13C n.m.r. of butadiene grafted polypropylene

¹H dipolar decoupled ¹³C n.m.r. experiments with the aid of the magic angle spinning technique have been used to determine the graft content and the isomer content of the polybutadiene grafts in a graft copolymer with isotactic polypropylene.     

有色丙纶细旦棉型短纤维生产及纺纱技术研究

定性地分析和讨论有色PP细且棉型短纤维生产及其纺纱过程的主要因素,着重探讨有色母粒对成品纤维性能及纺纱过程的影响,确定最佳纺丝工艺条件,控制 PP 有色细且短纤维物理性能,以满足纺纱工艺要求.     

Thermoplastic extrusion—the mechanism of the formation of extrudate structure and properties

Systems processed by thermoplastic extrusion can be regarded as heterophase polymer melts of incompatible water-plasticized biopolymers. In the process of thermoplastic extrusion, proteins and polysaccharides are melted at high pressure and temperature below the temperature region of their thermal decomposition. Dispersed particles of these systems can be deformed in flow. The mixed-melt anisotropic structure, formed in flow, is fixed by rapid conversion of the melt jet that lets the extruder die from a viscous state to a rubber-like state and then to a glassy state caused by cooling and drying. Incompatibility of proteins and polysaccharides in their water-plasticized melt mixtures impacts on structure formation and texturization during thermoplastic extrusion. Presented at the 20th ISF World Congress and 83rd AOCS Annual Meeting and Expo, May 10–14, 1992, Toronto, Ontario, Canada.     

冷再生结构层力学响应分析

通过研究冷再生结构层受力分析,在室内试验数据基础上,采用有限元BISAR软件对冷再生结构层以及常规半刚性路面结构层进行力学响应分析,得出了常规半刚性基层与冷再生基层力学响应的差异、冷再生层合理厚度、冷再生基层路面铣刨深度以及冷再生基层路面的使用条件.该研究对冷再生结构层设计与施工具有一定的借鉴作用.