电路电磁兼容建模与仿真

提出了对暴露在任意外场中的传输线进行时频分析的新方法，这种方法非常稳定，它能够与任意的传输线模型和电路仿真方法兼容，并且使用这种方法得到的仿真值和实际值之间的差别小于1％。     

大型连杆流线简易试验方法

介绍了一种大型连杆流线的简易试验方法及其评价原则。该方法可清晰显示流线，并适合任何尺寸和形状的锻造连杆的流线试验。     

Mean residence time of gas in mechanically agitated gas–liquid contactors

In the present study of gas–liquid contactors, mean residence/contact time was calculated from knowledge of superficial velocity and the gas phase hold-up, for various gas rates and impeller geometry and speeds, and compared with values obtained from RTD measurements. A new correlation, involving Flow Number, Froude Number, system geometry and the physical properties, is proposed. This uses the authors data and those available in literature.     

一种自动布线方法：多级线探索法

本文介绍了一种在微机上实现的印制板自动布线方法──多级线探索法及其编程方法。这种方法是基于完备布线算法的概念，通过分析李氏算法和传统线探索法的不足之处而得到的。虽然它也是一种线探索法，但有较传统线探索法更强的探索能力，不需要结合李氏算法而能单独完成布线任务，是一种较理想的算法，通过实验获得了较为满意的效果。     

The effect of a solid additive on rolling fatigue life

Behaviour of a series of lubricant oils and the effect of a non stoichiometric inorganic compound, as solid extreme pressure additive, on rolling fatigue life are studied using the rolling four-ball accelerated service simulation test proposed by Barwell and Scott. The results show, in all tested cases, the remarkable efficacy of this type of additive. The Total Acidity Number (tan) was found to increase with performance time for the case of the base lubricant, while for the oils with additives, it remained at its constant low value. This led to a proposal of a possible mechanism of the additive performance in the rolling process.     

Numerical simulation of typical contact situations of brake friction materials

In the paper, a model typical for contact situations of automotive brakes is established based on the method of movable cellular automata. The processes taking place at local contacts in an automotive brake system are analysed. Based on microscopic and micro-analytical observations, the following contact situations were simulated: (i) a couple of ferritic steel against pearlitic steel, both covered by an oxide layer mixed with graphite nanoparticles and (ii) the same situation but without oxide layers. The results of calculated mean coefficients of friction of the oxide-on-oxide contact correspond well to expected values for a real braking system, whereas steel-on-steel contact are twice as high. This allows one to make some conclusions; for example, oxide formation will take place more quickly than friction layer elimination, and finally this is responsible for the stabilisation of the coefficient of friction.     

Three dimensional boundary element analysis of internal cracks under sliding contact load with a spherical indenter

Using boundary element based three dimensional modelling for linear fracture mechanics, we present an analysis of cracking in a homogeneous medium subject to contact load. The proposed iterative solution procedure allows a simultaneous treatment of a reasonable number of partially closed cracks. It is shown that the most probable direction of propagation of a vertical internal crack is strongly dependent on its size compared to the contact radius and its location with respect to the axis of maximum normal load.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

Effective lightning protection schemes for distribution line

The causes of lightning outage are subdivided into direct lightning strokes and induced lightning strokes, which are identified by the characteristics of the lightning overvoltage. In the past, lightning protection devices were directed mainly toward the latter, and attention has been focused on the installation of lightning protection devices, ground wires, and reinforcement of insulators. However, lightning outages continue to occur. Thus it is extremely important to clarify the fault characteristics of lightning surges and to study the effectiveness of various lightning protection devices by considering both direct lightning stroke and induced lightning stroke in order to prevent lightning outage in the future. In this research, the electromagnetic transients program (EMTP) has been applied to the direct lightning stroke, and the induced lightning outage analysis program for multiple conductor systems has been applied to the induced lightning stroke to study the effectiveness of lightning protection devices provided by combination of various lightning protection devices. The most effective lightning protection schemes are analyzed and evaluated based on verification tests on the full scale models as well as economic considerations.     

CIMS装配和拆卸生产线的可靠性分析

本文对ＣＩＭＳ装配线和拆卸线的可靠性问题进行研究。文中分析了它们的运行状况，求出了两种生产线的稳态可用度，并用一个例子加以说明。