汽车发动机电机铁芯用钢(ADW2)的研制开发

鞍钢研制开发的汽车发动机启动电机用钢是针对汽车电机铁芯用钢（定、转子）而开发的电机钢类产品。介绍了该产品的研制过程及规格、特点。通过批量试制及装机试验，产品巳满足用户的使用要求。     

冷轧厂酸洗机组3号横剪大流量中高压液压系统设计方案探讨

在宝钢２０３０ｍｍ冷轧厂酸洗机组中，为了满足厚规格ＩＦ钢的生产，拟将原有的气动式剪切机改成液压式剪切机。为此，设计了一套中高压大流量的液压系统以满足３号横剪大剪切力（最高达７００ｋＮ）和快速剪切（３秒／次）的需要。由于采用了蓄能器增速回路和二通插装阀控制技术，使该液压系统较传统的剪切机液压系统具有响应速度快、体积小、重量轻、发热少和降低电机能耗等优点。     

A novel method of suppressing the inrush current of transformers by using a series‐connected voltage‐source PWM converter

This paper proposes a novel method of suppressing the inrush current of transformers. A small‐rated voltage‐source PWM converter is connected in series to the transformers through a matching transformer. As the connected PWM converter serves as a resistor for the source current, no inrush phenomena occurs. The required rating of the PWM converter, which serves as the damping resistor for the inrush phenomena, is 1/400 that of the main transformers in single‐phase circuits. In three‐phase circuits, it is 1/900. The basic principle of the proposed method is discussed. Digital computer simulation is implemented to confirm the validity and excellent practicability of the proposed method using the PSCAD/EMTDC. A prototype experimental model is constructed and tested. The experimental results demonstrate that the proposed method can perfectly suppress the inrush phenomena. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 157(4): 56–65, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20174     

压水堆堆芯换料设计优化的研究

讨论压水堆堆芯换料设计优化问题，并研制一套实用的换料优化软件包，可用于低泄漏、外－内和改进的外－内装料方案的优化。在低泄漏方案优化时，利用哈林原理将燃料组件布置与可燃毒物配置的优化问题脱耦成两步优化问题。先用线性规划方法进行无可燃毒物时燃料组件布置的优化，然后再用可变容差法寻找可燃毒物的优化布置。应用该软件对秦山核电厂首次难芯换料方案进行了优化，提出了可供参考的一些优化布置方案。     

THE STICKY ISSUES OF DRYING

Unconrolled agglomeration of particles and adhesion of the particulate mass to wall surfaces are common severe problems in many drying operations. This paper reviews the mechanisms of interparticle and particle-surface attraction as well as the theory and the existing tests for characterising powders in terms of internal strength, wall friction and adhesion. The usefulness of the information obtained from these tests in dryer design and operation is critically reviewed. The importance of powder stickiness in various types of dryers is discussed and established methods of combating the problem are presented Recommendations an made for further research in the area of powder cohesion and adhesion.     

横波速度各向异性初步探讨：—多波勘探资料的应用

在纵波、SH 型横波资料处理和解释过程中,我们发现四川 HBC 地区地下介质普遍存在方向各向异性。当横波通过方向各向异性介质时,分裂成两个波:一个波的偏振方向与裂缝平行,叫快横波;另一个波的偏振方向与裂缝走向垂直,叫慢横波。采用相应的观测和处理方法,便可获得快横波和慢横波剖面。根据同一界面的快、慢横波的旅行时可以求得各向异性系数。同样,还可以利用 SH 波与转换波的速度比求取各向异性系数。各向异性系数的大小,反映了裂缝的发育程度。如果野外作了 X、Y 分量观测,室内又作了坐标旋转处理,那么,就可以进一步确定裂缝带的方向。如果未作上述工作,也可以根据构造线走向,大致确定裂缝带的发育方向。     

Optical scattering in beef steak to predict tenderness using hyperspectral imaging in the VIS-NIR region

The objective of this research is to develop a non-destructive method for predicting cooked beef tenderness using optical scattering of light on fresh beef muscle tissue. A hyperspectral imaging system (λ = 496–1,036 nm) that consists of a CCD camera and an imaging spectrograph, was used to acquire beef steak images. The hyperspectral image consisted of 120 bands with spectral intervals of 4.54 nm. Sixty-one fresh beef steaks, including 44 strip loin and 17 tenderloin cuts, were collected. After imaging, the steaks were cooked and Warner-Bratzler shear (WBS) force values were collected as tenderness references. The optical scattering profiles were derived from the hyperspectral images and fitted to the modified Lorentzian function. Parameters, such as the peak height, full scattering width at half maximum (FWHM), and the slope around the FWHM were determined at each wavelength. Stepwise regression was used to identify 7 key wavelengths and parameters. The parameters were then used to predict the WBS scores. The model was able to predict WBS scores with an R = 0.67. Optical scattering implemented with hyperspectral imaging shows limited success for predicting current status of tenderness in beef steak.     

Preparation of monodisperse poly(vinyl alcohol) microspheres by heterogeneous surface saponification and iodine complex formation

Monodisperse poly(vinyl acetate) (PVAc) microspheres with high molecular weight obtained by suspension polymerization of vinyl acetate were saponified in alkaline aqueous solution to keep their spherical structure. The saponification was restricted on the surface of the PVAc microspheres and obtained particles had skin/core structure. Various poly(vinyl alcohol) (PVA) microspheres with different diameters and degrees of saponification (DSs) were obtained. The conversion of PVAc to PVA during the heterogeneous surface saponification time were examined by nuclear magnetic resonance spectroscopy and after 72 h hydrogel type PVA microspheres completely saponified were obtained. The crystal melting temperatures of the microspheres obtained by the saponification were measured a constant value of 238°C irrespective of varying DS, and the peaks became enlarged as reaction time. Iodine complexes were formed in saponified microspheres with DS of 41% and 99% by immersing them in I₂/KI aqueous solution and decomposed by the reduction of I₂ in the complexes to 2I^? using sodium sulfite to confirm whether the skin formed through the saponification was composed of PVA with high VA content. Obviously, characteristic blue color developments owing to I₅^?‐PVA complexes were observed in both saponified regions and a red in the PVAc core. Consequently, it was concluded that the PVA skins formed by heterogeneous surface saponification had high DSs. Such complexes endowed polymeric microspheres a good radiopacity which would be useful in clinical treatment of vascular diseases and were examined by X‐ray irradiation image. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

The magnetic applications choice among ferrite ceramics,metallic strips,or metal powder cores

Iron-based metallic strip materials such as iron, silicon-iron, and amorphous metal are used for low frequency (50–60 Hz. line) power applications. Low-loss Nickel-based alloys as high permeability strip or insulated powder cores are the choices for stable, low-level higher frequency applications. Iron-based powder cores offer low cost as power supply filter chokes. Ceramic ferrites combine highest frequency operation with low cost and reduced component size as transformers and chokes in telecommunication and high frequency power supply applications.