空间红外大口径折射式低温镜头设计与验证

针对目标探测类空间红外相机大范围成像、高灵敏度探测、高精度定位等应用需求,文中提出采用像方远心光路和低温光学技术结合的解决方案,设计了物方视场角8°×8°、入瞳口径265 mm、工作温度200 K的像方远心折射式光学系统。镜头最大口径280 mm,采用多级分散的弹性支撑设计,解决大口径低温透镜装框、透镜组件支撑和镜头整体安装各环节的热应力卸载问题。在保证高刚度和低漏热的情况下,使低温下透镜的热应力对镜头能量集中度的影响降低到可接受范围内。镜头完成装调及室温下像质确认后,进行了力学振动试验,并将其制冷到200 K水平测试像质,测试结果表明,镜头能量集中度达到轴上75%,边缘视场72%。     

可倾瓦径向气体轴承在低温透平机械中的应用

可倾瓦径向动压气体轴承以其良好的稳定性和自对中能力在低湿透乎机械中获得了广泛的应用。对可倾瓦径向气体轴承的工作原理和在低湿透乎机械中的应用发展情况进行了综述。     

低温粉碎系统中旋风分离器设计

旋风分离器是一种应用离心力进行粉体分离的设备。低温粉碎系统应用它分离粉体并起集粉作用。它的效率决定了物质回收率。本文从离心加速度与重力加速度的比值，筒体的高低，筒体直径，进口速度叙述对分离器效率的影响。着重叙述筒体直径确定方法，以及我们设计造长筒形旋风分离器的具体结构和令人满意的试验结果。     

高压低温先导式安全阀的设计

介绍了一种某试验系统用高压低温先导式安全阀,主要从工作原理、结构特点、材料的选用、结构特点、试验等方面进行阐述。     

Effect of pretreatments and freezing rate on the firmness of potato tissue after a freeze–thaw cycle

The texture of potato tissue after a freeze–thaw process using different freezing rates and different pretreatments was analysed, in order to select the best strategy for optimum preservation of the textural characteristics of pre‐frozen potato. Ten blanching conditions were tested and a two‐step blanching process with calcium chloride (0.07 g mL^?1) proved the most effective in protecting the tissue after a freeze–thaw process (maximum load force around 10–55% of the raw tissue, depending on potato batch, for air‐blast freezing and 20–60% for immersion freezing). Vacuum impregnation at 100 and 400 mbar, even when followed by different pre‐drying treatments to remove excess water, was very detrimental to resistance to a freeze–thaw process (maximum load force below 10% of the raw tissue for air‐blast freezing and below 20% for immersion freezing). Microstructure analysis confirmed better tissue integrity retention with ethyleneglycol immersion freezing instead of air‐freezing. Differences were found between batches with a 6‐month difference in storage time, indicating that the fresher batch was more suitable for freezing.     

Radiation effects on insulators for superconducting fusion magnets

Fibre-reinforced plastics (FRPs) are candidate materials for the insulation of superconducting magnet coils in future fusion reactors. This paper reports on a test programme performed to assess the mechanical properties of these materials and to obtain information on the damage and fracture mechanisms. Different types of FRPs (epoxies and poly- and bismaleimides as resins; two- and three-dimensional E-, S- or T-glass fabrics as reinforcements) were irradiated at room temperature by 2 MeV electrons and ⁶⁰Co-gamma rays up to 1.8 × 10⁸ Gy and by different reactor spectra up to a neutron fluence of 1 × 10²³ m⁻² (E > 0.1 MeV) at room temperature, 80 K or 5 K. Mechanical tests in tension as well as in the intralaminar crack opening and shear mode were carried out on the irradiated samples at 77 K. After low temperature irradiation, half of the samples were subjected to a warm-up cycle to room temperature before testing at 77 K. Results on the influence of different radiation sources and annealing cycles on the mechanical properties of these materials will be discussed.     

提高Cr12MoV钢冷作模具寿命的措施

从原材料改锻、预备热处理、淬火及回火、深冷处理、表面强化处理等方面分析介绍了提高Cr12MoV钢冷作模具寿命的一些方法和措施 ,并通过实例表明 ,采用这些方法和措施可较大幅度地提高模具寿命     

Effect of deep cryogenic treatment on mechanical behavior of a Cu-Cr-Zr alloy for electrodes of spot welding

The effects of deep cryogenic treatment on mechanical behavior of a Cu-Cr-Zr alloy for electrodes of spot welding were investigated employing Brinell-hardness testing unit, abrasion examination machine, electronic almighty testing machine and X-ray stress analyzer. Tensile fracture surfaces of the alloy were characterized by scanning electronic microscope （SEM） with energy dispersive X-ray spectroscopy （EDS）. The results showed that, after deep cryogenic treatment, σb and σ0.2 increased 23 MPa and 21 MPa respectively, the wear rate of the alloy exhibited the trend of decrease with the decreasing temperature and increasing time of deep cryogenic treatment, and the surface residual stress of the alloy was partially eliminated by deep cryogenic treatment.     

深冷处理提高镀锌钢板点焊电极寿命的机理

为了提高镀锌钢板点焊电极寿命，作者提出了镀锌钢板点焊电极的深冷处理方法。采用不同深冷处理工艺参数处理了点焊镀锌钢板的Cr—Zr—Cu合金电极，用这些电极进行了镀锌钢板点焊电极寿命试验并与未深冷处理的电极寿命进行了比较。用扫描电子显微镜对深冷处理电极进行了背散射及面扫描分析，用X射线衍射法观测了深冷处理前后的电极晶粒度，测试了电极在深冷处理前后的电阻率。通过对深冷电极微观结构的观测及电极性能的测试，探讨了深冷处理提高镀锌钢板点焊电极寿命的机理。研究结果表明，深冷处理提高了镀锌钢板点焊电极基体的致密性，改变了合金元素的分布，细化了电极材料的晶粒，提高了镀锌钢板点焊电极的导电、导热能力及电极抗压渍变形的能力，从而提高了镀锌钢板点焊电极的寿命。     

“车家宝”胶在制氧机超低温管路漏气上的应用

本文对“东家宝”胶在制氧机超低温管路漏气上的应用作了简要的介绍。