基于神经网络和遗传算法的锭子弹性管性能优化

为得到减振弹性管对下锭胆的支承弹性和锭子高速运动下的稳定性等性能的最优匹配效率,依据减振弹性管的等效抗弯刚度及底部等效刚度系数公式,利用MatLab数值分析软件构建弹性管抗弯刚度和底部挠度数学模型。首先,结合Isight优化软件基于径向基神经网络构建其近似模型,且使精度达到可接受水平,并以模型的关键结构参数弹性模量、螺距、槽宽、壁厚为设计变量,结合遗传算法对弹性管抗弯刚度和底部挠度进行多目标优化设计,得到Pareto最优解集和Pareto前沿图,确定出减振弹性管结构工艺参数的优化方案。通过对优化数据进行分析发现,该方案在保证减振弹性管弹性的同时,其底部振幅明显减弱。     

On the linear correlation between microhardness and mechanical properties in polar polymers and blends

The tensile elastic modulus (E), yield stress (σ_Y) and microhardness (MH) of neat and binary and ternary blends of glassy semicrystalline ethylene–vinyl alcohol copolymer (EVOH), a glassy amorphous polyamide and a semicrystalline nylon‐containing ionomer covering a broad range of properties were examined. The tests were carried out on dry and water‐equilibrated samples to produce stiffer and softer materials, respectively. From the results, more accurate linear correlations were found to describe adequately the microhardness, modulus and yield stress of these strongly self‐associated polymers through hydrogen bonding. Copyright © 2003 Society of Chemical Industry     

三重介质油藏干扰试井压力动态特征

在建立三重介质油藏试井解释模型的基础上，对该类油藏的干扰试井压力动态变化进行了研究；分析了井筒储存、表皮系数、窜流系数以及弹性储容比对观测井井底压力的影响。结果表明，表皮系数对观测井的井底压力没有影响，而井筒储存是否会对观测井井底压力造成影响取决于井筒储存系数的大小以及激动井和观测井之间的距离，窜流系数和弹性储容比对观测井井底压力的影响与单井试井的结果相类似。     

复合材料层合曲梁分层问题的解析解法

根据叠加原理将含有分层的复合材料层合曲梁在横向载荷作用下的受力状态分解为在面受力状态与出面受力状态,再将出面受力状态分解为无分层曲梁受横向载荷状态与含分层曲梁承受附加剪切载荷状态。将分层问题归结为在附加剪切载荷状态中,层合梁附加位移与附加应力的分析,并据此建立了一个简单的力学模型。最后得到了由分层引起的附加位移与应力的解析解答,并用能量释放率方法确定了应力强度因子。     

火炮身管内表面激光硬化处理的实验研究

提高身管寿命是火炮行业亟待解决的关键技术问题，激光表面改性技术是解决这一问题的有效方法之一。本文在分析激光表面相变硬化性能的基础上，对身管内表面进行了激光硬化处理实验研究，检测了其内表面阳线和阴线的硬化层硬度和深度，对比分析了离焦量和焦深对其内表面硬化层硬度的影响，并对激光相变硬化层金相组织进行了分析。经激光硬化处理后，身管的内表面硬度有明显提高，硬化层较深，且为很细的条状马氏体组织。     

Damage Development in Gray Cast Iron under Static Deformation

The authors discuss the results of experimental investigation of structural degradation of gray cast iron at various stages of static tensile deformation. Analysis of the deformation process has revealed that damageability of a material under loading can be assessed by both a special strain parameter and scatter of hardness characteristics or a ratio of the modulus deviation to the current value of the elastic modulus. A correlation between these parameters has been established.     

Overlapping Schwarz and Spectral Element Methods for Linear Elasticity and Elastic Waves

The classical overlapping Schwarz algorithm is here extended to the spectral element discretization of linear elastic problems, for both homogeneous and heterogeneous compressible materials. The algorithm solves iteratively the resulting preconditioned system of linear equations by the conjugate gradient or GMRES methods. The overlapping Schwarz preconditioned technique is then applied to the numerical approximation of elastic waves with spectral elements methods in space and implicit Newmark time advancing schemes. The results of several numerical experiments, for both elastostatic and elastodynamic problems, show that the convergence rate of the proposed preconditioning algorithm is independent of the number of spectral elements (scalability), is independent of the spectral degree in case of generous overlap, otherwise it depends inversely on the overlap size. Some results on the convergence properties of the spectral element approximation combined with Newmark schemes for elastic waves are also presented.     

微桥法镍膜的弹性模量和残余应力测量

利用MEMS技术制作了不同尺寸的镍(Ni)膜微桥结构样品。采用纳米压痕仪XP系统测量了微桥载荷与位移的关系,并结合微桥力学理论模型得到了两种不同尺寸的Ni膜的弹性模量和残余应力。结果表明,两种不同尺寸的Ni膜的弹性模量结果一致,为190 GPa左右,但是残余应力变化较大。与采用纳米压痕仪直接测得的带有硅(Si)基底的Ni膜弹性模量186.8 7.5 GPa相比较,两者符合较好。     

线光栅扫描实现衍射图形的矢量化直写

在双光束激光直写系统中,衍射光变图像的光刻是逐像素点进行的.本文提出在该系统中采用狭缝获得光栅线来进行衍射图形的直写,利用一种改进的矢量文件格式,使平台沿着垂直光栅线的方向运动,获得连续的多光点同时直写,直写后的衍射光栅线是连续的,系统的运行效率是逐点光刻的几十倍.编写了与DXF文件的接口直写控制程序,给出了实验结果.