The effect of rice bran on physicochemical,textural and glycaemic properties of ready-to-eat extruded corn snacks

In this work, corn extruded snack products were enriched with rice bran (RB) at 10% and 15%. A co-rotating twin-screw extruder was used with a feed moisture content of 16 g 100 g⁻¹, a screw speed of 240 r.p.m. and four heating sections of the barrel (100, 140, 150 and 150 °C). The impact of RB inclusion on nutritional profile, starch digestion, physicochemical and textural properties of snack products was evaluated. RB-enriched extrudates showed a lower specific volume and hardness and higher crispness than control. RB at 15% gave a water-holding capacity lower than control. Rheology of extrudate dispersions indicated an increase in elastic interactions and solid-like behaviour with RB supplementation. Differences in rheological properties resulted in attenuation of predictive glycaemic response for RB-enriched snacks.     

Novel pearl millet couscous process for West African markets using a low-cost single-screw extruder

Traditional West African pearl millet couscous products are popular; however, their preparation is laborious, time-consuming and energy-demanding, involving agglomeration, steaming, drying and sieving steps. In this study, a process was developed to produce millet couscous using a high pressure, high temperature and low-cost single-screw extruder. The innovation was to directly process the cooked low-moisture extrudate to a couscous product by drying and milling to the appropriate particle size (ranging between 1 and 2 mm). Throughput for the traditional process as prepared for commercial sale is 50 kg per day, but with the same amount of labour, the extrusion process yields ~350 kg per day. A consumer sensory study held in Niamey (Niger) showed that the extruded millet couscous was comparable to traditional couscous, though this was dependent on selection of the proper millet variety. This novel extrusion process could stimulate small- to medium-scale manufacturing of couscous and couscous-type products in West Africa.     

塑料挤出型材车间公用工程设计

鉴于当今人们对塑料门窗需求量的增大，通过对5个塑料挤出型材车间的设计，将其公用工程设计整理成文，总结出塑料挤出型材车间的采暖通风设计，压缩空气系统设计，制冷系统设计的较详尽的方案，以供有关设计技术人员参考。     

超大型材生产经验

对几种超大型材挤压生产的工艺技术、工模具设计、挤压参数控制等过程进行了分析，通过例子总结了挤压生产超大型材的经验及关键技术。     

橡胶卷材挤出连续硫化生产线的结构特色与工作原理

介绍了橡胶防水防腐卷材挤出连续硫化生产线的结构、特点和工作原理;指出在目前国内同类设备中,该生产设备具有先进性,并可替代引进设备。     

Influence of the ethylene–(methacrylic acid)–Zn2+ ionomer on the thermal and mechanical properties of blends of poly(propylene) (PP)/ethylene–(vinyl alcohol) copolymer (EVOH)

The thermal and mechanical properties and the morphologies of blends of poly(propylene) (PP) and an ethylene–(vinyl alcohol) copolymer (EVOH) and of blends of PP/EVOH/ethylene–(methacrylic acid)–Zn²⁺ ionomer were studied to establish the influence of the ionomer addition on the compatibilization of PP/EVOH blends and on their properties. The oxygen transmission rate (O₂TR) values of the blends were measured as well. PP and EVOH are initially incompatible as was determined by tensile tests and scanning electronic microscopy. Addition of the ionomer Zn²⁺ led to good compatibility and mechanical behaviour was improved in all blends. The mechanical properties on extruded films were studied for 90/10 and 80/20 w/w PP/EVOH blends compatibilized with 10 % of ionomer Zn²⁺. These experiments have shown that the tensile properties are better than in the injection‐moulded samples. The stretching during the extrusion improved the compatibility of the blends, diminishing the size of EVOH domains and enhancing their distribution in the PP matrix. As was to be expected, the EVOH improved the oxygen permeation of the films, even in compatibilized blends. Copyright © 2004 Society of Chemical Industry     

喷射沉积SiCP/Al复合材料及6066铝合金热挤压工艺的研究

作者应用喷射共沉积工艺制备 6 0 6 6 / Si Cp复合材料和 6 0 6 6铝合金锭坯 ,在不同的挤压比、挤压温度下挤压成　　型 ,用金相显微镜观察材料的显微组织 ,并测试了材料的力学性能。结果表明 :Si C/ Al复合材料喷射沉积状态的组织很疏松 ,存在许多的间隙 ,其密度约为理论密度的 86 % ,Si C颗粒在复合材料中分布不均匀 ,喷射沉积铝合金基体的致密度可达 90 % ;挤压过程使 Al/ Si Cp复合材料的大多数空隙消失 ,致密程度随挤压比的增大而增大 ,挤压比超过 14 .7后不会明显变化 ,而铝合金基体的致密程度与挤压比的变化关系不明显 ;挤压温度对材料的致密程度影响不大 ;Al/ Si Cp复合材料性能在挤压比超过 14 .7后变化不大 ;铝合金的性能不受挤压比变化的影响 ;而挤压温度过高使材料性能下降     

Failure analysis of a hot extrusion die used for Al-Li alloy processing

Al-Li alloys being developed as lighter, substitutes for conventional high strength Al alloys are to be processed by routine methods. During extrusion of a 8090 Al-Li alloy, the extrusion die container failed causing some alarm. This failed die container was analysed to examine if the failure was caused by interaction of Li diffusing out of Al-Li alloy with the carbides of die steel. The evidence, although not conclusive, is sufficient to exercise caution during such processing.     

综合应用地震属性、测井数据反演储层参数

本文研究了样点地震属性的特征提取，利用BP神经网络建立测井声波时差和地震属性的非线性映射关系。采用距离加权平均对研究区所有井的反演结果进行外推。为了提高分辨率和计算结果的准确性，详细分析、研究了适合于地震信号分解和重构的小波，以及测井声波时差和地震波阻抗与层界面的关系。最后，对反演的声波时差资料进行界面影响校正，进而计算出较符合实际情况的孔隙率参数。经已知井和新钻井验证，计算结果和实际情况相一致，效果令人满意。     

内外齿复合冷挤压成型实验研究

通过对轿车转向盘毂件内外齿进行的复合挤压实验研究 ,得到了新式复动式复合挤压模具结构 ,并确定了一种合理的成型工艺方案