Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

JETS,PLUMES AND BUOYANT JETS IN STATIC ENVIRONMENT

Turbulence represents an essential aspect in atmospheric and oceanic circulations.In particu-lar,it is a preponderant factor in the dispersion of pollutants of artificial or natural origin.Thevertical turbulent jets,plumes and buoyant jets discharging into static environment is one of themost important and basic flow patterns related with the environment pollution.These flows havenumerous important applications,for example,thrust augmentors,waste disposal plumes fromstacks and combustion systems,and significant problems of turbulent diffusion.     

建(构)筑物机械拆除方法综述

介绍了几种常用的建(构)筑物机械拆除方法,对其工作原理、特点、应用条件及局限性加以分析和说明。     

钨铜合金药型罩及其性能

钨铜合金药型罩的应用可以提高射流对均质钢靶的侵彻能力.这一提高得益于射流密度的提高以及断裂时间的延长. 本文对钨铜合金射流及其断裂形态通过X光照像进行了研究.它的旋转效应及其炸高特性也进行了实验研究. 钨铜合金药型罩的威力实验在φ30 mm的破甲弹上进行.在相同装药条件下与紫铜罩相比,威力提高20～30%.     

热流体喷射变形机理与喷嘴结构

高速短程纺技术能生产三维卷曲短纤维,该技术的关键之一是热流体喷射装置。本文介绍了热流体喷射装置的演变与特点及它的加工机理和某些已应用的实际装置。     

影响喷气燃料与橡胶相容性的因素

采用几种具有不同初始物理性能及不同丙烯腈含量、不同硫化剂和硫化程度的丁腈橡胶，考察了其配方和物理性能对采用不同工艺条件生产的喷气燃料的相容性。结果表明，喷气燃料与橡胶的相容性不仅与喷气燃料的加工工艺有关，而且与橡胶的组成及其制备工艺有关。采用非加氢工艺生产的喷气燃料与橡胶的相容性好于采用加氢工艺(特别是加氢裂化工艺)生产的喷气燃料。橡胶材料的初始力学性能的好坏并不完全决定其与喷气燃料相容性的好坏，橡胶材料的耐过氧化物侵蚀能力才是影响相容性好坏的主要因素。橡胶的组成和其制备工艺决定了橡胶在喷气燃料中萃取物的数量和组成，不同萃取物的综合作用给相容性带来不同程度的影响。用硫作硫化剂的橡胶虽然原始强度低于用过氧化物作硫化剂的橡胶，但前者与喷气燃料的相容性却远好于后者。     

Pulsating Jet Impingement Heat Transfer Enhancement

This article presents results from a numerical study of pulsating jet impingement heat transfer. The motivation is to seek conditions offering a significant enhancement compared to steady flow impingement drying. The CFD software package FLUENT was used for simulating slot-type pulsating jet impingement flows with confinement. The parameter study included velocity amplitude ratio, mean jet velocity, and pulsation frequency. The distance from nozzle exit to surface was three times the hydraulic diameter of the nozzle. The Reynolds number based on the nozzle hydraulic diameter and jet temperature was 2,460 with a mean jet velocity of 30 m/s, which is the base case of the numerical experiments. Results showed that time-averaged surface heat transfer increased with increasing velocity amplitude for the same mean jet velocity. Large velocity amplitudes helped enhance heat transfer by two mechanisms: high jet velocity during the positive cycle and strong recirculating flows during the negative cycle. For the cases with different mean jet velocities but the same maximum velocity, time-averaged surface heat flux decreased with decreasing mean jet velocity. As for the effects of pulsation frequency, with high-velocity amplitude ratio, time-averaged surface heat fluxes were at the same level regardless of frequency. However, at low-velocity amplitude ratio, high frequency caused stronger recirculating flows resulting in greater heat transfer compared to the cases with a lower frequency.     

激光测速仪在宽厚板轧机后测长的运用

随着国内厚板产量的增加,其市场竞争日趋激烈。为了更好的谋求发展,莱钢宽厚板厂在降低生产成本的同时,通过技术改造极大地提高产品的质量。因为板坯成材规格需要精确的长度数据,所以宽厚板板坯长度的精确测量就显得非常重要。本文主要介绍激光测速仪在轧机后测长系统中的应用。     

四辊铝箔轧机预控参数在线整定

介绍Ф210mm/Ф500mm× 800mm四辊液压轧机厚度预控系统中采用人机界面实现参数在线调整的方法,能大大提高预控参数的控制精度,减少轧机产品的厚度误差,是厚度自动控制的一项创新.     

用LG55冷轧管机轧制小直径不锈钢管孔型改进

介绍了ＬＧ５５冷轧管机使用Φ７～３２ｍｍ、Φ５０～３２ｍｍ孔型轧制小直径不锈钢管的工艺特点。试验表明，两种孔型可行，且Φ５７～３２ｍｍ孔型的综合使用效果更好。