Strain‐rate‐dependent mechanical properties of polypropylene separator for lithium‐ion batteries

The mechanical integrity of battery separators is critical for battery safety and durability. A comprehensive study of strain‐rate‐dependent tensile and puncture properties of a polypropylene lithium‐ion battery separator is presented here with a new model. Due to anisotropy of the polymeric membrane, tensile testing was conducted for different directions. Results showed that tensile strength and elastic modulus were increased 1000% and 500%, respectively, for different directions. It was also demonstrated that tensile strength changed 10 to 25% with strain rate (1.67 × 10^?4 to 1.67 × 10^?1 s^?1) for different directions. An equation was obtained for the first time for flow stress versus strain rate at varied tensile directions with respect to machine direction. Moreover, puncture testing was performed and it was shown that puncture strength was increased 140% with increasing strain rate from 0.25 to 250 mm min^?1. Two failure modes were also observed in puncture samples. Finally, Eyring's model was used to calculate activation enthalpy of the porous polypropylene separator. © 2020 Society of Chemical Industry     

NBR/PP热塑性弹性体研究进展

阐述了NBR／PP共混热塑性弹性体动态硫化胶的国内外研究进展、微观相态结构、性能、应用及展望。     

Study of the morphology and mechanical properties of polypropylene composites with silica or rice‐husk

The mechanical, morphological behavior and water absorption characteristics of polypropylene (PP) and silica, or PP and rice‐husk, composites have been studied. The silica used in this study as filler was a commercial type produced from soluble glass or rice husks. The compatibilizing effect of PP grafted with monomethyl itaconate (PP‐g‐MMI) and/or with vinyltriethoxysilane (PP‐g‐VTES) as polar monomers on the mechanical properties and water absorption was also investigated. In general, a high loading of the studied fillers in the polymer matrix increases the stiffness and the water absorption capacity. This effect is more noticeable in the tensile modulus of the PP/silica composite with PP‐g‐VTES as compatibilizer. However, the increase of the rice‐husk charge as a natural filler in the PP matrix decreases the stiffness, and in the presence of PP‐g‐MMI as compatibilizer in PP/rice‐husk, the tensile modulus and water absorption of the composite were improved. The better adhesion and phase continuity in the PP/silica and PP/rice‐husk composites with different compatibilizers was confirmed by the morphological study. Copyright © 2004 Society of Chemical Industry     

Liquid viscosities and densities of HFC-134a+glycol mixtures

Liquid viscosity and density of six binary mixtures of HFC-134a with glycols [ethylene glycol, diethylene glycol, triethylene glycol, polyethylene glycol (400), and polypropylene glycol (2000)] have been measured in the temperature range from 273 to 333 K. The viscosity was measured by a rolling-ball viscometer calibrated with standard liquids of viscosities and densities (JS5, JS10, JS20, and JS50). The density was measured with a glass pycnometer. The uncertainties of the measurements were estimated to be less than 3.4 % for viscosity and 0.04 % for density, respectively. An equation is given to represent the obtained viscosity values as a function of weight fraction and temperature.     

Melt index prediction by weighted least squares support vector machines

Melt index is considered an important quality variable determining product specifications. Reliable prediction of melt index (MI) is crucial in quality control of practical propylene polymerization processes. In this paper a least squares support vector machines (LS‐SVM) soft‐sensor model of propylene polymerization process is developed to infer the MI of polypropylene from other process variables. Considering the use of a SSE cost function without regularization might lead to less robust estimates; the weighted least squares support vector machines (weighted LS‐SVM) approach of propylene polymerization process is further proposed to obtain a robust estimation of melt index. The performance of standard SVM model is taken as a basis of comparison. A detailed comparison research among the standard SVM, LS‐SVM, and weighted LS‐SVM models is carried out. The research results confirm the effectiveness of the presented methods. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 285–289, 2006     

F级高云母含量云母带的研制及应用

本文介绍了一种F级高云母含量云母带，它的主要特点是云母含量高达48％以上，具有良好的长时间耐电热老化性能，适用于高压电机主绝缘多胶模压工艺要求，该云母带的应用对提高电机绝缘水平和延长电机使用寿命具有重要意义。     

聚丙烯催化剂的研发进展

综述了用于丙烯聚合的Ziegler-Natta催化剂在给电子体技术及催化剂制备工艺等方面,茂金属催化剂在制备丙烯均聚物、丙烯共聚物及特殊聚丙烯等方面,非茂单活性中心催化剂在丙烯活性聚合、丙烯与极性单体共聚及水介质聚合等方面的研发进展;讨论了聚丙烯催化剂的前景。     

助催化剂对TiCl_4/MgCl_2催化丙烯高温聚合的影响

研究了助催化剂种类(三甲基铝、三异丁基铝、三正己基铝、三乙基铝和甲基铝氧烷)及其含量对无内、外给电子体的TiCl4/MgCl2催化剂催化丙烯高温(100℃)聚合性能的影响,并用结晶分级分析、示差扫描量热和凝胶渗透色谱等方法分析了所得聚丙烯的结晶熔融行为和微观结构。实验结果表明,聚合温度从70℃升至100℃时,TiCl4/MgCl2催化剂的定向能力基本不变;100℃聚合时,以烷基化能力较弱的三异丁基铝为助催化剂时TiCl4/MgCl2催化剂的活性最高,而采用烷基化能力最强的三甲基铝为助催化剂时TiCl4/MgCl2催化剂的活性最低;100℃聚合时,助催化剂的种类对TiCl4/MgCl2催化剂的定向能力影响很小。     

低乙烯含量抗冲聚丙烯的结构表征

采用二甲苯为溶剂，将不同乙烯含量（５％￣１５％质量）的抗冲聚丙烯用特定程序进行分级，将各样品分为室温下可溶于甲苯和不可溶于甲苯的两部分。使用＾１３Ｃ－ＮＭＲ方法和ＦＴ－ＩＲ方法对各组分进行表征，明确了乙烯链段在聚丙烯链上的分布，并在此基础上提出了产生这种链结构的聚合工艺的特点。     

Rheology in Processing of in Situ Composites of Polypropylene and Low Melting Poing Metals

The low melting point metallic tin powder or alloy of tin and lead was blended with polypropy-lene. A kind of in situ composite has been prepared. The variations of torque were studied when the composites were mixed in Haake torque rheogeniometer. By way of capillary extrusion, effects upon rheology of the in situ com-posites of the low melting point metals (LMPM) and coupling agent for their different variety and content, were investigated. From flow curves, the results indicate that in situ composites mixed with the LMPM are a kind of pseudoplastic fluid. If the LMPM were melted, the higher the content of the LMPM , the lower apparent viscosity of composites. Meanwhile, when the coupling agent is added into composites, the viscosity of composite will go up first and drop then. This shows that the LMPM have a promoter flow action on the polypropylene.