Metal chlorides-promoted ammonia absorption of deep eutectic solvent

Ammonia is considered as a promising hydrogen or energy carrier. Ammonia absorption or adsorption is an important aspect for both ammonia removal, storage and separation applications. To these ends, a wide range of solid and liquid sorbents have been investigated. Among these, the deep eutectic solvent (DES) is emerging as a promising class of ammonia absorbers. Herein, we report a novel type of DES, i.e., metal-containing DESs for ammonia absorption. Specifically, the NH₃ absorption capacity is enhanced by ca. 18.1–36.9% when a small amount of metal chlorides, such as MgCl₂, MnCl₂ etc., are added into a DES composed of resorcinol (Res) and ethylene glycol (EG). To our knowledge, the MgCl₂/Res/EG (0.1:1:2) DES outperforms most of the reported DESs. The excellent NH₃ absorption performances of metal–containing DESs have been attributed to the synergy of Lewis acid–base and hydrogen bonding interactions. Additionally, good reversibility and high NH₃/CO₂ selectivity are achieved over the MgCl₂/Res/EG (0.1:1:2) DES, which enables it to be a potential NH₃ absorber for further investigations.     

Nb和时效时间对热轧中锰TRIP钢中P偏聚的影响

热轧态中锰TRIP钢首先经650 ℃退火2 h,随后在550 ℃进行等温时效热处理,采用场发射扫描电镜(FE-SEM)研究该钢中P的偏聚和时效析出行为的变化情况。结果表明,中锰TRIP钢中P在晶界的偏聚是一种非平衡偏聚现象,临界时间约为50 h,与理论计算结果48 h较为吻合。在局部偏聚区域内,C与P存在共偏聚的关系,即P偏聚量高的地方,C含量也高。而合金元素Nb具有抑制P偏聚的效果,在20~70 h时效时间内,可以相对降低6.57%~19.5%的最大P偏聚量。根据电子背散射衍射(EBSD)菊池线分析,P偏聚量低于2.28at%时,P为固溶状态,高于2.28at.%时,P为析出状态。     

综合高速效应的凝析气藏流入动态

当井底压力低于露点压力时,凝析液在近井地带开始析出并不断聚集产生凝析油堵塞现象。因此,在制定凝析气井工作制度时,通常以控制生产压差为指导思想,往往忽略高速流动下凝析气液相变的非平衡特征。对于凝析气体系,当外界温压变化速度超过凝析气液的相平衡速度时,凝析气体系相变滞后,开始呈现非平衡特征,即凝析液的析出量随着压降速度的增加而减小。凝析气在向井筒流动的过程中,近井区高速流动使凝析气产生非平衡相变,凝析气在比较高的压降速度下流入井筒,使得凝析液来不及析出。在分析非平衡相变规律与近井地带凝析气渗流参数分布的基础上,评价凝析气液流动过程中的非平衡特征,给出了考虑非平衡相变的凝析液饱和度分布计算公式,并进行了产能预测结果对比。实例分析表明,可以通过适当放大生产压差,增加凝析气液相变非平衡特征,减小井筒附近的凝析液饱和度,提高气井产能与气藏开发效果。     

Effects of solidification structure on fatigue crack initiation and fatigue strength in Al−Si−Mg cast alloys

Rotating-bending uniaxial fatigue tests and micro-fatigue crack initiation tests were carried out using a permanent mold cast (PMC) and semi-solid die cast (SDC) with Al−7%Si−0.35%Mg composition in order to examine the relationship between solidification structures and fatigue behaviors. The crack length was measured using a replication method. Fatigue strength was improved in SDC, which was almost consistent with the predicted fatigue strength using the size of Si particle cluster. Resistance to fatigue crack initiation and fatigue strength were improved in SDC owing to the finer Si cluster and to higher ultimate tensile strength. Fatigue crack in PMC was preferentially initiated at pores. For SDC, the fatigue crack was initiated at the Si particle/matrix interface, and then sucessively grew along eutectic cell boundaries.     

高压脉冲放电处理含氰废水的影响因素探讨

焦化废水中含有大量的氰化物,必须采取有效措施进行去除,传统去除方法运行成本高、操作复杂。提出了用高压毫微秒脉冲产生的非平衡等离子体处理含氰废水的方法,对其影响因素pH值、放电时间、气流量、放电条件等进行了大量的实验研究,结果表明:溶液初始pH值为9.09,放电2 h,放电电压46 kV时氰化物的去除率最高可达93.2%,氰化物质量浓度可降至0.26 mg/L。实验对比了放电与不放电氰化物的去除效果:相同条件下放电后氰化物的去除率大大提高,为焦化废水中氰化物的去除提出了一种新的方法。     

Phase equilibria in the system Al-Rh

Methods of differential thermal analysis, x-ray diffraction, microstructural analysis and electron probe microanalysis are used to study alloys of the Al-Rh system over the whole concentration range. It is established that the phase of equiatomic composition AlRh melts congruently at 2060°C and it has an extended range of homogeneity (45.1–54.2 at.% Rh). The solubility of aluminum in rhodium reaches 9 at.%, decreasing to 6 at.% at 850°C. Coordinates are determined for the eutectic point l ⇆ AlRh + 〈Rh〉 as 70 at.% Rh and 1715°C. The existence of intermediate phases, their crystal structure, and also the method of forming phases in the field of composition rich in aluminum given in publications are confirmed. __________ Translated from Poroshkovaya Metallurgiya, Nos. 5–6(449), pp. 48–56, May–June, 2006.     

不同磁场作用对AZ31镁合金的凝固组织的影响

镁合金是具有优越性能的金属材料,镁合金的加工是目前国内外正在深入进行研究的新课题.实验发现在镁合金的凝固过程中施加低频或静态磁场都能细化晶粒,但静磁场得到的细化效果要优于低频交流磁场,同时随磁感应强度的增加,静磁场细化晶粒的效果明显提高;在静磁场条件下晶界共晶体组织的厚度明显减小,同时在晶内出现了大量细小块状化合物,这有利于改善镁合金的综合性能.     

过共晶Al－Si合金共生区激光表面处理

用２ｋＷ连续ＣＯ２激光对过共晶Ａｌ－１８Ｓｉ合金以不同能量密度和扫描速度进行快速熔凝处理。用扫描电镜、电子微区分析仪分析了微观结构。从计算机对Ａｌ－Ｓｉ合金ｆ－ｎｆ系统的非平衡理论计算所得的共生区及实验结果的分析可见，当能量密度和扫描速度决定的凝固条件处于共生区中部时，过共晶Ａｌ－Ｓｉ合金激光表面处理可以得到共晶间距低于２００ｎｍ的完全共晶结构。     

纤维共晶生长界面前沿三维扩散场解析

修正Ｊａｃｋｓｏｎ和Ｈｕｎｔ关于在垂直生长方向截面上溶质扩散各向同性假设，求解三维Ｌａｐｏｌａｃｅ方程，获得纤维共晶生长界面前沿三维稳态扩散场，并证明Ｊａｃｋｓｏｎ和Ｈｕｎｔ的二维模型是实际生长的二维简化和一阶近似，并用丁二腈（ＳＣＮ）一梓脑（ＣＡＭ）纤维共晶系统计算生长界面前沿溶质分布。