Finite element piezothermoelasticity analysis and the active control of FGM plates with integrated piezoelectric sensors and actuators

 An efficient finite element model is presented for the static and dynamic piezothermoelastic analysis and control of FGM plates under temperature gradient environments using integrated piezoelectric sensor/actuator layers. The properties of an FGM plate are functionally graded in the thickness direction according to a volume fraction power law distribution. A constant displacement-cum-velocity feedback control algorithm that couples the direct and inverse piezoelectric effects is applied to provide active feedback control of the integrated FGM plate in a closed loop system. Numerical results for the static and dynamic control are presented for the FGM plate, which consists of zirconia and aluminum. The effects of the constituent volume fractions and the influence of feedback control gain on the static and dynamic responses of the FGM plates are examined. Received: 13 March 2002 / Accepted: 5 March 2003 The work described in this paper was supported by a grant awarded by the Research Grants Council of the Hong Kong Special Administrative Region, China (Project No. CityU 1024/01E).     

Experimental and numerical investigation of fracture in double-edge notched steel plates

Double-edge notched (DENT) steel plates were pulled until complete fracture and several experimental observations were made (using profilometry and scanning electron microscopy). The essential work of fracture (EWF) model was found to be well verified. Numerical simulations—up to the maximum load only—of some experiments were performed using the finite element method (FEM), and incorporating geometric and material non-linearities (large deformation elasto-plasticity). Some experimental measurements were compared with the corresponding numerical computations and excellent agreement was found.     

Analytical Calculation of Large-Scale Deflection of Pulse-Loaded Elliptic Plates

Large deflections of pulse-loaded elliptic and round plates made of hardenable elastoplastic materials are investigated analytically using an energy-based approach. Formulas that are convenient for engineering design have been derived.     

空气中烧成的镍导体及其应用

将空气中烧成的镍导体用于散热制冷片制作工艺中，可降低成本，提高合格率。通过实验得到的最佳值为：镍导体中４号玻璃（ＳｉＯ２＞３０，Ｂ２Ｏ３＞１０，ＰｂＯ＜５５，ＴｉＯ２少许）的含量４．５％，化学镀镍时间５０ｍｉｎ，方阻４７．５ｍΩ／□，附着力８．１Ｎ／ｍｍ２。     

Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.     

曙光油田超稠油井套管损坏的机理和防治

超稠油特殊的油藏特点决定了其生产周期短、注汽频繁、出砂、汽窜、超覆现象严重，以及套管质量等因素的影响，套管损坏较为严重。对曙光油田超稠油井套管损坏的规律和机理进行了研究，并从钻井和完井工艺的完善、套管钢级和射孔工艺的选择、采油生产参数的确定、注汽管柱隔热效果的提高、防治砂工艺等方面，对套管损坏提出了预防措施和对策。并对套管损坏井制定了修复再利用方案。     

孔径法测量铜带残余应力的试验研究

介绍了用于薄板残余应力测量的新方法——孔径法,该方法是通过测量冲孔直径的变化来间接求出各方向的残余应力;文中详细阐述了残余应力的标定方法;由于可针对不同材料建立了被测材料的平均应力(σ_l)与被测板材宽度(B)、厚度(H)以及冲孔后直径变化率(△D_i/D)之间的数学模型,因而使薄板残余应力测量变得简便而经济;此外还对该方法的分辨率与测量精度进行了实验、计算与分析。     

用于多种组装技术的厚膜导体复合结构

厚膜导体Ｐｄ－Ａｇ／Ａｕ、Ｐｔ－Ｐｄ－Ａｕ／Ａｕ平面复合结构，Ｐｄ－Ａｇ／Ａｕ立体复合结构可使多种组装技术相互兼容。立体复合结构还可有效地降低导体线电阻，减少线损耗。而且，其超声键合性尤佳     

Hydride Vapor Phase Epitaxy of GaN Thick Films by the Consecutive Deposition Process Using GaCl3

GaN buffer and main layers were grown by the conventional hydride vapor phase epitaxy technique using GaCl₃ consecutively. The deposited buffer layers were investigated by atomic force microscopy and X-ray analysis. To examine the behavior of the buffer layers at main layer growth temperature, heat treatment was conducted at 900°C. Based on the results of the buffer layer study, GaN thick films were grown at 1050°C. Optimum deposition conditions of buffer layer from the buffer and main layer studies generally coincided. On the φ scanning pattern, the GaN films grown on (0001) Al₂O₃ were single-crystalline. Band-edge emission dominated photoluminescence was observed at room temperature.     

鄂尔多斯西缘前陆盆地巨厚黄土地区地震采集技术

鄂尔多斯西缘前陆盆地表层地质地貌极其复杂，有巨厚黄土区、黄土-沙漠区及山前砾石-黄土区，独特的黄土地貌使得地震采集面临着诸多技术难题。根据以往巨厚黄土地区地震采集经验，采用多种方法系统地开展黄土表层结构精细调查，深入研究黄土地球物理特征及激发因素与表层黄土结构之间的关系，优选激发井位和井深，确保了激发效果；采用小道距、三线小线距、高密度空间采样技术，获得了高信噪比、高分辨率地震资料。研究表明，巨厚黄土地区地震采集时应优选激发井位和岩性，合理选择激发井深；坚持多深井组合激发、单井药量不宜过大总药量要大两项基本原则；采用高密度采样技术，提高采集资料的覆盖次数和信噪比。图10表1参15