Statistical Piezotronic Effect in Nanocrystal Bulk by Anisotropic Geometry Control

Utilizing inner-crystal piezoelectric polarization charges to control carrier transport across a metal-semiconductor or semiconductor–semiconductor interface, piezotronic effect has great potential applications in smart micro/nano-electromechanical system (MEMS/NEMS), human-machine interfacing, and nanorobotics. However, current research on piezotronics has mainly focused on systems with only one or rather limited interfaces. Here, the statistical piezotronic effect is reported in ZnO bulk composited of nanoplatelets, of which the strain/stress-induced piezo-potential at the crystals’ interfaces can effectively gate the electrical transport of ZnO bulk. It is a statistical phenomenon of piezotronic modification of large numbers of interfaces, and the crystal orientation of inner ZnO nanoplatelets strongly influence the transport property of ZnO bulk. With optimum preferred orientation of ZnO nanoplatelets, the bulk exhibits an increased conductivity with decreasing stress at a high pressure range of 200–400 MPa, which has not been observed previously in bulk. A maximum sensitivity of 1.149 µS m⁻¹ MPa⁻¹ and a corresponding gauge factor of 467–589 have been achieved. As a statistical phenomenon of many piezotronic interfaces modulation, the proposed statistical piezotronic effect extends the connotation of piezotronics and promotes its practical applications in intelligent sensing.     

基于神经网络和遗传算法的锭子弹性管性能优化

为得到减振弹性管对下锭胆的支承弹性和锭子高速运动下的稳定性等性能的最优匹配效率,依据减振弹性管的等效抗弯刚度及底部等效刚度系数公式,利用MatLab数值分析软件构建弹性管抗弯刚度和底部挠度数学模型。首先,结合Isight优化软件基于径向基神经网络构建其近似模型,且使精度达到可接受水平,并以模型的关键结构参数弹性模量、螺距、槽宽、壁厚为设计变量,结合遗传算法对弹性管抗弯刚度和底部挠度进行多目标优化设计,得到Pareto最优解集和Pareto前沿图,确定出减振弹性管结构工艺参数的优化方案。通过对优化数据进行分析发现,该方案在保证减振弹性管弹性的同时,其底部振幅明显减弱。     

Dielectric,ferroelectric, and piezoelectric properties of lead-free Ba0.95Ca0.05Ti1-xZrxO3 ceramics

Abstract

Ba_0.95Ca_0.05Ti_1-xZr_xO₃ (BCTZO) ceramics were prepared by a solid state reaction method. The samples were characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM) and X-ray absorption near edge structure (XANES). The ceramics exhibit a pure perovskite structure. The average grain size gradually decreases with increasing Zr concentration. XANES results indicate that the intensities of pre-edge peaks dropped with increasing Zr concentration. The BCTZO ceramic of x?=?0.05 has the optimum electrical properties with the maximum dielectric constant (ε'_m), remanent polarization (2P_r), coercive electric field (2E_c) and piezoelectric charge constant (d₃₃) of 7,244, 12.54 (μC/cm²), 5.29 (kV/cm) and 288 (pC/N), respectively.     

混凝土结构的压电声波检测分析

本文介绍了混凝土结构的压电体波和表面波检测的主要进展,对两种压电声波检测的优缺点进行了总结。体波检测设备一般埋入混凝土内部,需要选择合理的检测部位,检测结果较为精确;声表面波检测无需选择特定的部位,但是检测深度有限。在实际检测工作过程中,可以联合两种方法相互验证。     

磁流变阻尼器抑制转子系统振动试验

针对大型旋转机械通过临界转速时振动过大及运行中故障频发等问题,搭建转子试验台,模拟启停机过程和碰摩、不对中故障。不改变原有支撑形式,安装自主设计的磁流变阻尼器,在不停机的情况下,试验研究阻尼器抑制转子通过临界转速时振动过大及各类故障振动。试验结果表明,阻尼器可以有效抑制转子系统临界转速附近的振动,降幅在60%以上;转子发生碰摩或不对中故障时,阻尼器可以降低其高倍频振动。     

Experimental research on dynamic response of PZT-5H under impact load

In order to improve the stability of PZT-based sensors, the mechanical, dielectric, ferroelectric and piezoelectric properties of PZT-5H under impact load were studied experimentally by using the separated Hopkinson pressure bar (SHPB) with an electrical output measurement device. At the same time, the experimental study on the material properties of PZT-5H before and after the impact was carried out. The effect of impact cracks on the output voltage of PZT-5H was also analyzed. The results show that the dynamic piezoelectric constants of PZT-5H under low stress impact (10–50 MPa) are different from those under quasi-static state, and the empirical relationship between them and the peak stress is obtained through experiments. The dielectric properties of PZT-5H did not change under low stress impact, but micro-cracks occurred in the material and dielectric loss increased at high frequencies. Under short circuit, the residual polarization intensity of PZT-5H decreases sharply due to impact load. While the impact load causes the secondary polarization and the increase of the residual polarization intensity of PZT under open circuit. When the stress is over 45 MPa, the PZT-5H breaks. The formation of cracks causes abnormal discharge voltage and gap discharge.     

Survey on Passivity Based Control of Induction Machine

Induction machines (IM) constitute a theoretically interesting and practically important class of nonlinear systems. They are frequently used as wind generators for their power/cost ratio. They are described by a fifth‐order nonlinear differential equation with two inputs and only three state variables available for measurement. The control task is further complicated by the fact that IM are subject to unknown (load) disturbances and the parameters can be of great uncertainty. One is then faced with the challenging problem of controlling a highly nonlinear system, with unknown time‐varying parameters, where the regulated output, besides being unmeasurable, is perturbed by an unknown additive signal. Passivity‐based control (PBC) is a well‐established structure‐preserving design methodology which has shown to be very powerful to design robust controllers for physical systems described by Euler‐Lagrange equations of motion. PBCs provide a natural procedure to "shape" the potential energy yielding controllers with a clear physical interpretation in terms of interconnection of the system with its environment and are robust vis á vis to unmodeled dissipative effects. One recent approach of PBC is the Interconnection and Damping Assignment Passivity‐Based Control (IDA‐PBC) which is a very useful technique to control nonlinear systems assigning a desired (Port‐Controlled Hamiltonian) structure to the closed‐loop. The aim of this paper is to give a survey on different PBC of IM. The originality of this work is that the author proves that the well known field oriented control of IM is a particular case of the IDA‐PBC with disturbance.     

基于振动实测的非均质地层钻头失效分析与对策

四川盆地作为国内页岩气开发的重点区域,通过近几年的不断攻关和实践,机械钻速得到了提高,但由于受地层复杂、可钻性差、非均质性强等地质因素的影响,导致井下钻柱系统不良振动剧烈,容易出现钻头损坏严重、钻速较低等问题,严重影响了钻井时效。为了解决上述难题,以该盆地涪陵工区上二叠统龙潭组—中二叠统茅口组为例,采用井下振动高频测量工具的实测手段,测量了钻头—钻柱系统的动态振动加速度参数,结合地层的岩性和矿物组分分析,研究钻头失效原因与对策,并开展了现场试验。研究结果表明:①在非均质地层中钻进的钻头—钻柱系统产生了大于40 m/s~2的高幅值瞬时冲击振动,高幅值的瞬时冲击是导致钻头先期失效的主要原因;②提出了抑制高幅值的瞬时冲击振动采用"减振+增压"工具组合和避免井下工具共振的钻井参数;③采用钻井新参数的试验井比邻井的高幅值瞬时振动降低了17%,单只钻头进尺增加24%,钻头工作环境得到了较大的改善,钻头使用数量减少。结论认为,该研究成果能够有效地改善钻头—钻柱系统的振动状态,有利于达成延长钻头使用寿命的目标。     

压电驱动器迟滞特性的Preisach模型研究

压电驱动器的迟滞特性是影响其位移输出精度的主要因素。该文采用改进的Preisach模型对压电驱动器的迟滞特性进行建模，并进行了相应的实验研究。实验结果表明该模型可以很好地预测压电驱动器在经过一定的控制电压序列以后的位移输出值．能够有效地降低迟滞特性对压电驱动器位移输出精度的影响。     

基于压电陶瓷动态信息的结构裂纹识别方法

利用压电陶瓷的动态特性和压电系统的动态信息,对铝梁的裂纹损伤进行了分析研究。随着梁裂纹尺寸的增加,压电陶瓷片的导钠幅值下降,且系统固有频率减小。利用导钠幅值的变化和系统的动态信息,可以对裂纹的位置和尺寸大小进行识别。实验证明该方法的有效性。