Novel electrically conductive and ferromagnetic composites of poly(aniline‐co‐aminonaphthalenesulfonic acid) with iron oxide nanoparticles: Synthesis and characterization

Nanocomposites of iron oxide (Fe₃O₄) with a sulfonated polyaniline, poly(aniline‐co‐aminonaphthalenesulfonic acid) [SPAN(ANSA)], were synthesized through chemical oxidative copolymerization of aniline and 5‐amino‐2‐naphthalenesulfonic acid/1‐amino‐5‐naphthalenesulfonic acid in the presence of Fe₃O₄ nanoparticles. The nanocomposites [Fe₃O₄/SPAN(ANSA)‐NCs] were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), X‐ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, elemental analysis, UV–visible spectroscopy, thermogravimetric analysis (TGA), superconductor quantum interference device (SQUID), and electrical conductivity measurements. The TEM images reveal that nanocrystalline Fe₃O₄ particles were homogeneously incorporated within the polymer matrix with the sizes in the range of 10–15 nm. XRD pattern reveals that pure Fe₃O₄ particles are having spinel structure, and nanocomposites are more crystalline in comparison to pristine polymers. Differential thermogravimetric (DTG) curves obtained through TGA informs that polymer chains in the composites have better thermal stability than that of the pristine copolymers. FTIR spectra provide information on the structure of the composites. The conductivity of the nanocomposites (～ 0.5 S cm^?1) is higher than that of pristine PANI (～ 10^?3 S cm^?1). The charge transport behavior of the composites is explained through temperature difference of conductivity. The temperature dependence of conductivity fits with the quasi‐1D variable range hopping (quasi‐1D VRH) model. SQUID analysis reveals that the composites show ferromagnetic behavior at room temperature. The maximum saturation magnetization of the composite is 9.7 emu g^?1. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Sulfonated polyimide and poly (ethylene glycol) diacrylate based semi‐interpenetrating polymer network membranes for fuel cells

Semi‐interpenetrating polymer network (semi‐IPN) membranes based on novel sulfonated polyimide (SPI) and poly (ethylene glycol) diacrylate (PEGDA) have been prepared for the fuel cell applications. SPI was synthesized from 1,4,5,8‐naphthalenetetracarboxylic dianhydride, 4,4′‐diaminobiphenyl 2,2′‐disulfonic acid, and 2‐bis [4‐(4‐aminophenoxy) phenyl] hexafluoropropane. PEGDA was polymerized in the presence of SPI to synthesize semi‐IPN membranes of different ionic contents. These membranes were characterized by determining, ion exchange capacity, water uptake, water stability, proton conductivity, and thermal stability. The proton conductivity of the membranes increased with increasing PEGDA content in the order of 10^?1 S cm^?1 at 90°C. These interpenetrating network membranes showed higher water stability than the pure acid polyimide membrane. This study shows that semi‐IPN SPI membranes based on PEGDA which gives hydrophilic group and structural stability can be available candidates comparable to Nafion® 117 over 70°C. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation and characterization of sulfonated polyetherimide/polyetherimide blend membranes

Polyetherimide (PEI) was sulfonated by chlorosulfonic acid (CSA) in 1,2‐dichloroethane for the first time. With the increase of the CSA/PEI repeat unit ratio and/or reaction time, the ion‐exchange capacity (IEC) of the sulfonated polyetherimide (SPEI) increased accordingly. Water‐uptake testing and contact‐angle measurement showed that the hydrophilicity of the SPEI increases with the increase of the IEC. Membranes were fabricated from SPEI/PEI blends with different ratios. The morphologies of the blend membranes were examined by scanning electron microscopy, which showed that the membrane pore size is larger when SPEI with higher IEC was used. With the increase of SPEI ratio in the blend membranes, the membrane pore size also increased. The contact‐angle data of the membranes showed that the hydrophilicity of the blend membrane was elevated because of the sulfonate group on the SPEI molecular backbone. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1709–1715, 2004     

油井水泥降失水剂SPS的制备和性能研究

通过磺化改性,制备了磺化聚苯乙烯(SPS)作为油井水泥降失水剂.研究了反应条件对SPS磺化度的影响、SPS的磺化度与失水控制的关系、SPS水泥浆体系的性能.实验结果表明:在相同的条件下,磺化度越高,失水控制越好;在最佳条件下制备的SPS具有良好的降失水性能,SPS的水泥浆体系具有良好的流变性能和较好的耐温性能;在120℃下,其水泥浆体系的稠化时间,用常用的缓凝剂可调整到337 min,SPS对水泥浆其他性能无不良影响.     

Preparation and properties of lithium sulfonated polyoxadiazoles electrolyte

以硫酸肼（HS）、对苯二甲酸（TPA）、4，4'-联苯醚二甲酸（DPE）为单体，发烟硫酸做溶剂和脱水剂一步合成了一系列不同TPA和DPE单体配比的磺化聚芳噁二唑（SPOD），再通过氢氧化锂中和得到聚芳噁二唑磺酸锂（Li-SPOD）聚合物电解质，采用浇铸成膜法制得Li-SPOD电解质膜，研究改变TPA和DPE两种单体配比对Li-SPOD结构及性能的影响。结果表明，几种不同单体配比均能实现在聚合过程中一步得到SPOD，磺酸基团接枝在DPE结构的苯环上，并且可以达到理论接枝量；同时Li-SPOD电解质膜的聚集态结构差异很小；热性能的表现均非常优异，初始热分解温度都在450 ℃以上；力学性能随DPE单体含量的增加稍有下降但依然保持在较高的水平；电导率约为10^-5S/cm级别，随DPE含量增加而逐渐降低；Li-SPOD固态电解质电化学稳定性较好，对锂稳定电化学窗口均在4.0 V以上。     

Effects of special nanoparticles on fuel cell properties of sulfonated polyethersulfone membrane

Polyethersulfone was sulfonated by changing the reaction time with sulfuric acid. The degree of sulfonation and ion exchange capacity were determined. Sulfonation of polyethersulfone was confirmed by FT-IR analysis and a new peak at 1025 cm^?1. Inorganic materials such as carbon nanotubes, graphene, and kaolinite nanoparticles were synthesized. The effects of three nanoparticles on thermal stability and water uptake of sulfonated polyethersulfone were investigated. The morphology of membranes were also altered due to the addition of inorganic materials. The proton conductivity of the modified membranes increased with respect to increase in relative humidity.     

Rheological and thermal stability of novel weak gels based on sulfonated polyacrylamide/scleroglucan/chromium triacetate

The present study deals with weak gels based on sulfonated polyacrylamide (SPA)/scleroglucan (SC)/Cr³⁺ with an exceptional thermal stability in electrolyte media. The rheological results showed that on increasing the SC concentration the shear viscosity and storage modulus of the SPA/SC/Cr³⁺ system were increased and the dependence of the storage modulus on frequency became weaker. The yield stress of the SPA/SC/Cr³⁺ system was higher than that of the corresponding SPA/SC system. The thermochemical stability increased with increasing relaxation time. The SPA/SC/Cr³⁺ semi‐interpenetrating network exhibited the lowest viscosity loss in electrolyte media; therefore this system may be a potential candidate for enhanced oil recovery applications. © 2016 Society of Chemical Industry     

Improving Blood Compatibility of Polyethersulfone Hollow Fiber Membranes via Blending with Sulfonated Polyether Ether Ketone

Appropriate membrane for blood contacting applications requires hemocompatibility and high permeation flux; it should inhibit proteins or platelets adsorption and still possess high permeability. Aiming to improve the polyethersulfone (PES) hollow fiber membrane hemocompatibility, sulfonated polyether ether ketone (SPEEK) is self‐synthesized in the present research and added to PES in different ratios. Scanning electron microscopy images have revealed significant changes in PES membranes structure after addition of SPEEK, which can influence water permeation property of the membranes. Water contact angles of the membranes have reduced from 75° to 50° after addition of 4 wt% SPEEK. Influence of SPEEK addition on hemocompatibility of the PES membranes is evaluated via protein (bovine serum albumin) adsorption, platelet attachment, and coagulation time (APTT and TT) assays. Obtained results reveal that hemocompatibility of the modified hollow fiber membranes is enhanced as a result of emerging repulsive forces between negative charges on the membranes surface and negatively charge blood components.

     

钻井液用阳离子型磺化酚醛树脂降滤失剂的研制

将阳离子结构单体在催化剂作用下引入酚醛树脂结构,再通过多步磺化反应制得阳离子型磺化酚醛树脂。简要描述了合成方法,检测了部分表征性能及作为水基钻井液降滤失剂的性能。在红外谱图中能清楚地看到阳离子结构。该结构样品在黏土颗粒上的饱和吸附量高达33.51 mg/g土,浊点盐度(以Cl-计)≥160g/L,参考石油天然气行业标准SY/T5094-2008将阳离子型磺化酚醛树脂200℃热滚16 h后在180℃,3.5 MPa条件下测试其滤失量,评价结果显示阳离子型磺化酚醛树脂的抗高温高压降滤失性优于现用SMP系列产品。     

锡酞菁及其磺化衍生物的合成与性质研究

以苯酐和氯化亚锡为原料,采用固相法合成锡酞菁(SnPc),再和发烟硫酸反应合成磺化锡酞菁(SnPcS)。用元素分析,红外光谱,紫外光谱对它们进行了表征。结果表明:磺化锡酞菁的溶解性比锡酞菁要大得多;热稳定性研究发现,磺化锡酞菁从100℃开始失去磺酸基,400℃酞菁环才开始分解;且磺化锡酞菁在水中的氧化还原过程具有可逆性;同时,对磺化锡酞菁的电子光谱进行了研究。