磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

消防战勤保障体系建设的思考

随着经济的发展,消防救援队伍承担的任务越来越繁重.重大灾害事故的发生,对消防战勤保障方面提出了更高的要求.文章主要从消防战勤保障的主要任务职能、消防战勤的任务分类以及消防战勤保障体系建设存在的问题与建议等几个方面进行了详细的阐述,以期消防战勤保障得到更好的发展.     

Simulation studies on a rotating ring disk electrode: Effects of ionic migration with kinetic complication-disk results

In continuation to my previous work (Guha S. AIChE J. 2013;59(4):1390-1399), in this work, effects of ionic migration are evaluated for disk region of a rotating ring disk electrode system by numerically solving complex differential equations, developed for mass transfer along with kinetic complication in presence of ionic migration under limiting current condition. The system for simulation is 0.01 M Fe₂(SO₄)₃ solution with H₂SO₄ as supporting electrolyte. Simulation cases are presence and absence of ionic migration with kinetic complication (oxidation of Fe²⁺ to Fe³⁺ under O₂ pressure). Results show that concentration boundary layer thickness of reactant Fe³⁺ reduces appreciably and steady-state disk current reduces substantially in presence of migration. Simulated steady-state disk current in absence of migration case agrees well with published data. Results indicate higher Fe²⁺ concentration in presence of migration and thereby higher rate of oxidation of Fe²⁺ to Fe³⁺ at all rate constant values.     

M1080B无心外圆磨床改进

M1080B无心外圆磨床砂轮及导轮宽度较窄,磨削轴承套圈外圆时,磨削效率低,托板架调整较为繁琐、皮带打滑、磨损较为严重。针对上述问题,提出了相应的解决办法,提高了磨削效率。     

埋地管道泄漏内封堵装置设计与研究

针对流体输送埋地管道泄漏问题,设计了一种利用管道机器人携带封堵气囊进行快速应急封堵修复的埋地管道泄漏内封堵装置。采用矩阵变换方法建立了牵引系统驱动轮过弯方程,利用MATLAB软件对过弯方程进行了验证,同时利用ADAMS软件仿真分析过弯路径与驱动轮转角对牵引系统行走速度的影响。研究结果表明:由两个串联封堵器组成的应急封堵系统可满足复杂工况下的管道泄漏封堵要求;牵引系统驱动轮在弯管内部行走时,单轮速度呈周期性变化,但三个驱动轮整体周期运动特性一致;驱动轮转角在25°~40°时,牵引系统行走速度与驱动轮转角成正比,且转角为30°时驱动效果最好。该内封堵装置的结构设计可为管道泄漏应急封堵领域装备的研发提供重要参考。     

Effect of grinding-induced cyclic heating on the hardened layer generation in the plunge grinding of a cylindrical component

This paper discusses the effects of the grinding-induced cyclic heating on the properties of the hardened layer in a plunge cylindrical grinding process on the high strength steel EN26. It was found that a multi-pass grinding brings about a uniform and continuous hardened layer along the circumference of the cylindrical workpiece. An increase of the number of grinding passes, leads to a thicker layer of hardening, a larger compressive residual stress and a deeper plastic deformation zone. Within the plastic deformation zone, the martensitic grains are refined by the thermo-mechanical loading, giving rise to a hardness of 12.5% higher than that from a conventional martensitic transformation. The coupled effects of heat accumulation and wheel wear in the multi-pass grinding are the main causes for the thickening of the hardened layer. A too small infeed per workpiece revolution would result in insufficient grinding heat, and in turn, bring about an undesirable tempered hardened layer and a reduction of its hardness.     

龙滩水电站地下厂房进水口高边坡加固支护设计

龙滩水电站地下厂房进水口高边坡开挖坡高达435m，坡面面积达27万m^2，为典型的反倾向层状结构岩质高边坡。为了确保进水口坝段的稳定，必须保持边坡岩体有足够的稳定性，通过采取边坡轮廓设计，防渗、排水设计，加固支护设计及施工控制等一系列措施，确保边坡稳定。文章简要论述了边坡设计的原则、标准、高边坡轮廓设计、防渗排水系统、加固支护措施、施工控制等情况。     

兼使水流转向的非对称窄缝挑坎

讨论了兼有水流转向功能的一级非对称直线边壁窄缝的设计方法与水力特性，两边墙转向角之差即为水流转向角，两边墙转角相等时出口水流的水深和佛汝德数也分别相等。按在窄缝出口前形成完整幅射流的条件，讨论了兼有转向功能的非对称曲线边墙窄缝的设计方法与水力特性。比较了六种体型(三种对称、三种非对称)窄缝在八种工况对泄槽底板的冲击压强，实测结果表明，非对称性越强冲击压强越小。     

土钉墙技术在华丰湾堤防工程边坡支护中的应用

在华丰湾堤防工程施工中 ,为防止因边坡开挖而造成附近房屋出现裂缝问题 ,经论证决定采用土钉墙技术对堤基开挖进行边坡支护 ;经实施 ,堤基开挖顺利 ,附近房屋无任何位移与沉降迹象。     

MON--未来城域网的发展方向

阐述了城域光网络(MON)技术的出现背景、定义、技术方案和特点，以及与现有城域基础设施的比较，突出说明了其应用上的竞争优势。最后介绍了MON的现状和前景展望。