Methodology for optimization of pouring variables using bottom pour for low masses of SS304 (<300 kg) in investment casting process (case study)

Bottom pour ladles with stopper rod systems are commonly used in the metal casting industry. However, stopper rod bottom-pouring systems have not yet been developed for the lower thermal masses of alloys typically used in the investment casting industry. Large thermal masses used with bottom pour systems are typically limited for ladles larger than 700 kg and to certain alloys with higher fluidity and longer solidification time like cast iron, aluminum alloys etc. In this study, bottom pour ladle designs and low thermal mass refractory systems have been developed and evaluated in production investment foundry trials with 300 kg pouring ladle. The ladles system and pouring practices used will be described along with the results from the pouring trials for SS304 that represents typical alloys used in Investment casting industries. Optimization of the variables used in an experimentation using Genetic algorithm is also explained.     

Behaviour of Surface Defects in Wire Rod Rolling

Defects are often present in rolled products, such as wire rod. The market demand for wire rod without any defects has increased. In the final wire rod products, defects originating from steel making, casting, pre‐rolling of billets and during wire rod rolling can appear. In this work, artificial V‐shaped longitudinal surface cracks have been analysed experimentally and by means of FEM. The results indicate that the experiments and FEM calculations show the same tendency except in two cases, where instability due to fairly “round” false round bars disturbed the experiment. FE studies in combination with practical experiments are necessary in order to understand the behaviour of the material flows in the groove and to explain whether the crack will open up as a V‐shape or if it will be closed as an I‐shape.     

一种弯曲抽油杆打捞工具

为安全、快速、有效地解决顶部极度弯曲、径向变形尺寸很大的落井抽油杆打捞难题,研制了一种在套管内打捞弯曲抽油杆的工具。该工具把以往从落物顶端引入打捞改为从落物侧面引入打捞,使复杂的井下故障处理简单化,从而缩短修井周期,减少修井费用,及时恢复油井生产。该项技术先后在江苏油田6口油井上应用,成功率100%,验证了工具的独特性和可靠性。     

双排桩门架—锚杆新型组合支护体系的应用研究

本文分析了双排桩门架支护结构的受力机理。针对工程实际进行变形分析,提出增设锚杆形成锚杆———双排桩门架式组合支护体系的方法,并与监测数据对比、验证。     

基于实际井眼轨迹的抽油杆柱API设计方法

目前的抽油杆柱设计方法大都基于设计井眼轨迹或经验公式，因此设计的抽油杆柱与井眼的匹配性并没有达到最优，结果可能影响了抽油杆柱的受力特性和寿命。概述了目前现有的抽油杆柱设计方法，提出了基于实际井眼轨迹的抽油杆柱API设计方法，即考虑到在三维空间中井下粘滞阻力及动载的影响，利用微单元分析方法计算出轴向载荷与轴向应力，然后在此基础上进行杆柱组合设计，并给出了设计流程。以江苏油田永21-3井为例，对几种设计方法的设计结果进行了对比分析，结果表明，江苏油田目前采用的抽油杆柱设计方法包含了人为经验因素，并不是最优的杆柱设计结果，有待进一步改进。     

摩擦换向抽油机悬点运动分析计算

摩擦换向抽油机采用开关磁阻电动机或变频调速电动机,其特点是可以频繁双向旋转,带动摩擦轮正反转,实现光杆的上行下行。该抽油机运动特点与游梁式抽油机运动特点有较大区别,文章分析了摩擦换向抽油机的运动特点,给出了该机悬点位移、速度、加速度的计算方法。     

大型连杆流线简易试验方法

介绍了一种大型连杆流线的简易试验方法及其评价原则。该方法可清晰显示流线，并适合任何尺寸和形状的锻造连杆的流线试验。     

碳纤维连续抽油杆作业车自动调平系统设计

为保证碳纤维连续抽油杆作业车作业时工作平台处于水平状态,防止侧翻,开展了作业车自动调平系统的设计。在给出自动调平系统构成的基础上,着重论述了系统的自动调平控制方案、自动调平控制原理以及自动调平控制软件的设计,给出作业车自动调平控制系统流程图。     

Analysis and simulations of vibrations of a beam with a slider

A model for vibrations of a beam with a slider is derived, analysed and numerically simulated. It describes a viscoelastic beam that is clamped at one end to a vibrating device, while the other end moves between two stops attached to a slider. The contact is described by the normal compliance or by the Signorini conditions. The existence of weak solutions is established using the theory of set-valued pseudomonotone operators. The model is discretized using fourth-order spatial discretization, the solutions are numerically simulated and their results presented. The dynamics of the vibrations are depicted and so are the noise characteristics of the system.     

停棒子系统与控制棒组操作范围监测试验

本文叙述了反应堆保护系统停棒与汽轮机降功率子系统的系统功能、保护参数和秦山核电站控制棒组插入监测器的设计与参数选择,确定了控制棒提升上极限值和在不同工况下棒插入低位、低-低位整定值,并在热态零功率条件下加以验证。试验证明参数选择是合理的,为功率运行阶段提供了数据。