Three-dimensional and anisotropic numerical analysis of a PEM fuel cell

In this study, the effects of cell temperature and relative humidity on charge transport parameters are numerically analyzed. In order to perform this analysis, three-dimensional and anisotropic numerical models are developed. The numerical models are integrated into the experimental values for anisotropic electrical conductivities, as depending on cell temperature and relative humidity, that were obtained from our previous study. The achieved results indicate that the values of current densities in the in-plane direction increase with increasing cell temperature and relative humidity, while the current densities reach a maximum in the rib regions for both the numerical model at the through-plane direction. The behaviors of electrolyte potentials are similar with changes in the cell temperature and relative humidity. In addition, the cathode electrical potentials in both the in-plane direction and through-plane direction do not change to a considerable amount with increasing cell temperature and relative humidity.     

On one boundary problem for nonlinear stationary controlled system

The object of study is nonlinear stationary controlled system of ordinary differential equations with constant disturbance in the right part. The problem of constructing the synthesising control function providing the transfer of this system from the initial state to the origin is considered. The sufficiently simple for numerical implementation algorithm of solution of the above-mentioned problem is obtained. It is shown that for local null controllability of the considered system, it is sufficient that the conditions of the Kalman's type were satisfied. In addition, the estimates restricting the choice of initial conditions and external disturbances under which the transfer is guaranteed are obtained. The main idea of the method of construction of the desired control function consists in reducing the original problem to stabilisation of a special kind linear non-stationary system and solving the Cauchy problem for an auxiliary system of ordinary differential equations closed by stabilising control. The simplicity of the realisation of this algorithm is determined by the construction of the auxiliary system and its stabilisation that could be obtained by analytical methods. The effectiveness of the method is illustrated by solving the problem of crane control and its numerical simulation.     

An overlapping domain decomposition dual reciprocity method

We present a domain decomposition boundary integral equation method for two-dimensional partial differential equations. The overlapping Schwarz method is employed to improve the dual reciprocity boundary element method. The resulting algorithm turns out to be more accurate than a non-overlapping approach previously proposed. Some numerical results showing the improved accuracy and efficiency of the methods are given.     

黄河龙口水利枢纽坝基岩体钙质充填夹层地质分析与试验研究

龙口水利枢纽坝基岩体主要由奥陶系中统马家沟组(O2m2)灰岩组成,其中发育有多层软弱夹层。作为其中之一的钙质充填夹层,强度虽不很低,但由于处于坝基下的持力层内,间距不大,发育密集,产状平缓,是坝基浅层抗滑稳定的主要控制因素,因此,在大坝抗滑稳定分析时,应进行分析和研究。     

多层梯度层InGaAs（P）InPSAGM雪崩光电二极管

本文报道采用液相外延（ＬＰＥ）生长和传统光刻制管工艺研制出引入多层（三层或三层以上）中间能带隙过渡的吸收区、倍增区分离的ＩｎＧａＡｓ（Ｐ）／ＩｎＰ雪崩光电二极管（简称ＩｎＧａＡｓ（Ｐ）／ＩｎＰＳＡＧＭＡＰＤ），其技术指标为：击穿电压ＶＢ＝４０～９０Ｖ；０．９ＶＢ时的暗电流Ｉｄ最小可小于１０ｎＡ；１．３μｍ时光响应度Ｒｅ＝０．６～０．８Ａ／Ｗ，倍增因子Ｍ≥２０（Ｍｍａｘ＞４０），过剩噪声因子Ｆ≌５和较宽频带响应特性。     

Stabilization of uncertain boundary control systems

We consider a class of linear infinite-dimensional systems subject to boundary uncertainties, which are linear and time-invariant. Using a deterministic approach to the design of stabilizing feedback controls, uniform exponential stability of the zero state is achieved. Lyapunov techniques are combined with Datko or Ichikawa theory. Three illustrative examples are presented.     

A note on the satisfaction of the boundary conditions for Chebyshev collocation methods in rectangular domains

The way boundary conditions are imposed when applying Chebyshev collocation methods to Poisson and biharmonic-type problems in rectangular domains is investigated. It is shown that careful selection of the number of collocation points leads to a linear system ofn linearly independent equations inn unknowns.     

Breakdown of oil films and formation of residual films

The breakdown processes of oil films under quasi-static loading have been investigated by using a newly developed steel-oil-mercury system. The relationship between the thickness and breakdown ratio of a hexadecane film is represented by a single master curve independently of the indentation speed, indentation load, and temperature. The master curve shows that the breakdown process of hexadecane includes two stages; one is the decrement of the thickness without breakdown and the other is the decrement of the thickness with a drastic progress of breakdown. By solving a small amount of fatty acid in hexadecane, the thickness increases and the breakdown ratio decreases noticeably; a multilayer residual film supporting normal load is formed between two metal surfaces. Experiments at different temperatures reveal a negative relationship between the temperature and thickness of residual film, which indicates that the residual film is organized by physical interaction rather than chemical interaction. At least under a lower concentration, the residual film appears to consist of not only fatty acid molecules but also hexadecane molecules.     

液晶光阀光电导层光吸收系数的研究

用化学气相沉积法制备了液晶光阀中光电导层———非晶硅薄膜,从实验中得出最佳制备工艺的参数取值。给出了用包络线法测量非晶硅薄膜光吸收系数的原理,测量了样品的光吸收系数随波长的变化规律。得到样品在最佳工艺条件下的光吸收系数高于1×103cm-1。     

Three dimensional boundary element analysis of internal cracks under sliding contact load with a spherical indenter

Using boundary element based three dimensional modelling for linear fracture mechanics, we present an analysis of cracking in a homogeneous medium subject to contact load. The proposed iterative solution procedure allows a simultaneous treatment of a reasonable number of partially closed cracks. It is shown that the most probable direction of propagation of a vertical internal crack is strongly dependent on its size compared to the contact radius and its location with respect to the axis of maximum normal load.