Preparation of Pt/Ce–Zr–Y mixed oxide/anodized aluminium oxide catalysts for hydrogen passive autocatalytic recombination

The use of a Pt-based catalyst was evaluated for autocatalytic hydrogen recombination. The Pt was supported on a mixture of Ce-, Zr- and Y-oxides (CZY) to yield nanosized Pt particles. The Pt/CZY/AAO catalyst was then prepared by the spray-deposition of the Pt/CZY intermediate onto an anodized aluminium oxide (AAO) layer on a metallic aluminum core. The Pt/CZY/AAO catalyst (3 × 1 cm) was evaluated for hydrogen combustion (1–8 vol% hydrogen in the air) in a recombiner section testing station. The thermal distribution throughout the catalyst surface was investigated using an infrared camera. The maximum temperature gradient (ΔT) for the examined hydrogen concentrations did not exceed 36 °C. The Pt/CZY/AAO catalyst was also evaluated for prolonged hydrogen combustion duration to assess its durability. An average combustion temperature of 239.0 ± 10.0 °C was maintained for 53 days of catalytic hydrogen combustion, suggesting that there was limited, or no, catalyst deactivation. Finally, a Pt/CZY/AAO catalytic plate (14.0 × 4.5 cm) was prepared to investigate the thermal distribution. An average surface temperature of 212.5 °C and a maximum ΔT of 5.4 °C was obtained throughout the catalyst surface at a 3 vol% hydrogen concentration.     

Dual effect synergistically triggered Ce:(Y,Tb)3(Al,Mn)5O12 transparent ceramics enabling a high color-rendering index and excellent thermal stability for white LEDs

Ce:Y₃Al₅O₁₂ transparent ceramics (TCs) with appropriate emission light proportion and high thermal stability are significant to construct white light emitting diode devices with excellent chromaticity parameters. In this work, strategies of controlling crystal-field splitting around Ce³⁺ ion and doping orange-red emitting ion, were adopted to fabricate Ce:(Y,Tb)₃(Al,Mn)₅O₁₂ TCs via vacuum sintering technique. Notably, 85.4 % of the room-temperature luminescence intensity of the TC was retained at 150 °C, and the color rendering index was as high as 79.8. Furthermore, a 12 nm red shift and a 16.2 % increase of full width at half maximum were achieved owing to the synergistic effects of Tb³⁺ and Mn²⁺ ions. By combining TCs with a 460 nm blue chip, a warm white light with a low correlated color temperature of 4155 K was acquired. Meanwhile, the action mechanism of Tb³⁺ ion and the energy transfer between Ce³⁺ and Mn²⁺ ions were verified in prepared TCs.     

基于局部分型面的电器外壳注塑模具设计

电器外壳制品形状结构复杂,有两处侧凸(孔)较难处理。通过对矩形孔内侧凸的结构分析,在其局部设计了分型面,避免了使用侧向抽芯机构;对侧孔部位设计了斜顶杆侧向抽芯机构,其结构简单、紧凑。模具采用一模二腔、平衡式布局,采用经扁推杆由制品内部进料的潜伏式浇口,S型流道。在NX 8.0中完成了模具结构设计。经实践证明,该模具结构合理,产品合格。     

Restructuring bank networks after mergers and acquisitions: A capacitated delocation model for closing and resizing branches

During restructuring processes, due to mergers and acquisitions, banks frequently face the problem of having redundant branches competing in the same market. In this work, we introduce a new Capacitated Branch Restructuring Model which extends the available literature in delocation models. It considers both closing down and long term operations׳ costs, and addresses the problem of resizing open branches in order to maintain a constant service level. We consider, as well, the presence of competitors and allow for ceding market share whenever the restructuring costs are prohibitively expensive.We test our model in a real life scenario, obtaining a reduction of about 40% of the network size, and annual savings over 45% in operation costs from the second year on. We finally perform a sensitivity analysis on critical parameters. This analysis shows that the final design of the network depends on certain strategic decisions concerning the redundancy of the branches, as well as their proximity to the demand nodes and to the competitor׳s branches. At the same time, this design is quite robust to changes in the parameters associated with the adjustments on service capacity and with the market reaction.     

Unraveling the effect of alumina-supported Y- doped ceria composition and method of preparation on the WGS activity of gold catalysts

The demands for high-purity hydrogen required in fuel-cell applications impose new goals and challenges for design of well performing water-gas shift (WGS) catalysts. Gold-based catalysts have exhibited high activity in the WGS reaction at low temperature. Preparation of appropriate and economically viable supports with complex composition by various synthesis procedures is an attractive approach to WGS performance improvement. The effect of two different preparation methods (wet impregnation or mechanical mixing) and ceria content (10, 20 or 30 wt%) on textural, structural, surface and reductive properties and WGS activity of gold catalysts was studied. Additionally, the role of Y₂O₃ as a promoter of ceria was examined. Long-term stability test was carried out at 260 °C over the most active catalyst. The composition of the best performing sample (composed of about 70 wt% alumina), prepared by mechanical mixing, was considered promising in case of practical applications because of its cost efficiency. The combination of gold nanoparticles and alumina supported Y-doped ceria proved an advantageous approach for developing new catalytic formulations with high effectiveness in clean hydrogen production.     

Vapor absorption by LiBr aqueous solution in vertical smooth tubes

Heat and mass transfer in a falling film vertical in-tube absorber was studied experimentally with LiBr aqueous solution. The presented results include the effect of solution flow rate, solution subcooling and cooling water temperature on the absorption in a smooth copper tube 16.05 mm I.D. and 400 mm long. The experimental data in the previous report for a 1200-mm-long tube was also re-examined and compared. It was demonstrated by the observation of the flow in the tube that the break down of the liquid film into rivulets leads to deterioration of heat and mass transfer at lower film Reynolds number or in longer tubes. An attempt to evaluate physically acceptable heat and mass transfer coefficients that are defined with estimated temperature and concentration at the vapor–liquid interface was also presented.     

An application of chemometric techniques to analyze the effects of the wave function modifications on the intermolecular stretching frequencies of the hydrogen-bonded complexes

Factorial design and principal component models are used to determine how ab initio H-bond stretching frequencies depend on characteristics of the molecular orbital wave functions of acetylene–HX, ethylene–HX and cyclopropane–HX π-type hydrogen complexes with X=F, Cl, CN, NC and CCH. The results obtained for the three sets of complexes show that factorial design and principal component analyses complement each other. Factorial design calculations clearly show that these frequencies are affected mostly by inclusion of electron correlation on the calculation level. On average, their values are increased by about 25 cm⁻¹ due to a change from the Hartree–Fock (HF) to Möller–Plesset 2 (MP2) level. Valence, diffuse and polarization main effects as well as valence–diffuse, diffuse–correlation and polarization–correlation interaction effects are also important to better describe a factorial model to the H-bond stretching frequencies of these hydrogen complexes. This simplified model has been successful in reproducing the complete ab initio results, which correspond to two hundred and forty calculations. Principal component analyses applied only to hydrogen-bonded complexes whose experimental frequencies are known, has revealed that the six-dimensional original space can be accurately represented by a bidimensional space defined by two principal components. Its graphical representation reveals that the experimental intermolecular stretching frequencies are in closest agreement with the MP2/6–31+G and MP2/6–311+G ab initio results.     

进入WTO后的企业设备管理思考

本文从企业设备管理战略、设备工程要成为培养“企业核心竞争能力”的平台、发挥行业协会作用三方面,提出了入世后企业设备管理的应对措施。     

Finite sample properties of estimators of spatial autoregressive models with autoregressive disturbances

The article investigates the finite sample properties of estimators for spatial autoregressive models where the disturbance terms may follow a spatial autoregressive process. In particular we investigate the finite sample behavior of the feasible generalized spatial two-stage least squares (FGS2SLS) estimator introduced by Kelejian and Prucha (1998), the maximum likelihood (ML) estimator, as well as that of several other estimators. We find that the FGS2SLS estimator is virtually as efficient as the ML estimator. This is important because the ML estimator is computationally burdensome, and may even be forbidding in large samples, while the FGS2SLS estimator remains computationally feasible in large samples. Received: 20 January 2001 / Accepted: 31 August 2001