井下原地溶浸技术试验研究

结合东同矿业公司井下原地溶浸的试验研究情况,分析了细菌浸出-萃取-电积工艺过程中存在的问题并提出了解决方法,探讨了该工艺应用研究的发展方向与前景。     

一种微粉碎新设备——离心碎磨一体机

介绍一种离心碎磨一体机的工作原理、构造和特点 ,分析了碎磨机理及应用前景     

锤头用中锰耐磨铸钢的生产与应用

含碳含硅较高的中锰铸钢是一种可用于制造锤头的耐磨铸钢，破碎白云石时，此种钢制作的锤头的单耗为７．１ｇ／ｔ，而高锰钢制作的锤头单耗为１７．４ｇ／ｔ。中锰耐磨铸钢属脆性材料，在非强烈冲击条件下使用，是高锰钢耐磨性的２．４５倍，适用于破碎中低硬度的矿石。文中介绍了中锰铸钢的成分、生产工艺、热处理过程和机械性能。     

乳山硫铁矿破碎工艺的改进

原矿含泥量大造成设备的堵塞。根据现场生产实际改用粉碎后的矿粒直接给入扇形孔条筛，筛下可调刮板使细粒均匀分布在皮带下面，粗粒复盖其上。物料到达皮带首轮处，使其呈抛掷状态，然后利用分离挡板除去细粒。首轮的直径和转速是按粒度分离的决定因素。分离细粒级后使中碎机生产能力增大，降低能耗，减少磨损，提高了设备运转率。     

Static indentation and unloading response of sandwich beams

This paper deals with analysis of foam core sandwich beams subject to static indentation and subsequent unloading (removal of load). Sandwich beams are assumed continuously supported by a rigid platen to eliminate global bending. An analytical model is presented assuming an elastic-perfectly plastic compressive behaviour of the foam core. An elastic part of indentation response is described using the Winkler foundation model. Upon removal of the load, an elastic unloading response of the foam core is assumed. Also, finite element (FE) analysis of static indentation and unloading of sandwich beams is performed using the FE code ABAQUS. The foam core is modelled using the crushable foam material model. To obtain input data for the analytical model and to calibrate the crushable foam model in FE analysis, the response of the foam core is experimentally characterized in uniaxial compression, up to densification, with subsequent unloading and tension until tensile fracture. Both models can predict load–displacement response of sandwich beams under static indentation and a residual dent magnitude in the face sheet after unloading along with residual strain levels in the foam core at the unloaded equilibrium state. The analytical and FE analyses are experimentally verified through static indentation tests of composite sandwich beams with two different foam cores. The load–displacement response, size of a crushed core zone and the depth of a residual dent are measured in the testing. A digital speckle photography technique is also used in the indentation tests in order to measure the strain levels in the crushed core zone. The experimental results are in good agreement with the analytical and FE analyses.     

HP700型圆锥破碎机在调军台选厂的初步实践

ＨＰ７００型圆锥破碎机具有优良的性能，增大了偏心距，加快了轴转速，采用曲线型（非阻塞型）破碎腔，从而在破碎腔内只需较低破碎力，在调军台选厂的初步实践达到了较好的效果。     

管磨机与球破机粉碎机理研究

本文由管磨机与球破机相关行业及其研究背景入手，说明课题的巨大研究价值。围绕水泥成品优质高产低消耗的目标，从管磨机与球破机料球截面筛析理论入手，揭示了管磨机与球破机的粉碎机理。由管磨机与球破机的机理比较引出了球破机与球磨机串联粉磨工艺理论，阐明了球破机作为新型破碎机械对水泥粉磨工艺的影响，必将对利用管磨机与球破机进行破碎粉磨的相关行业技术进步带来积极影响。     

硅砖熔洞的成因

通过硅砖熔洞、铁斑在硅砖检验中的重要性的阐述,对生产过程中出现的一些硅砖熔洞进行原因排查,探讨了硅砖铁洞、钙洞的成因及应采取的预防措施。     

Analysis of the Disintegration of Distiller's Spent Grain Compacts as Affected by Drying in Superheated Steam

Breaking and disintegrating of biomass compacts while they are being dried in superheated steam (SS) is a common problem observed during the initial stage of SS drying. The present work investigated the moisture and temperature changes, volume and density variation, crushing resistance, and tensile strength of single cylindrical compacts produced from wet distiller's spent grain (WDG) under SS drying conditions. The wet compacts were dried in SS at 110, 130, and 150°C with SS velocities of 0.9, 1.1, and 1.4 m/s. For a specific temperature and velocity, the compacts were exposed to SS for time periods of 5, 120, 300, and 600 s and the changes in physical properties were analyzed. An increase in a percentage increase in volume by 78–130% and a decrease in density by 51–61% were observed as a result of drying the compact in SS. The results obtained from the study were compared with hot-air dried compacts for 600 s, indicating that SS drying had a substantial role in stimulating the relaxation of stresses stored in the compacts as compared with a convection hot-air drying process.     

Fibre reinforced lightweight aggregates

Carbon steel fibre reinforced lightweight aggregates (LWA) were produced in a pilot scale rotary kiln. Narrow size fractions as well as not-sieved (as received) material were investigated according to European standards with a main focus on strength and density and compared to a reference material without fibres. Depending on the size of the pellets a fraction of the fibres oxidized during firing. A strength increase proportional to the amount of non-oxidized fibres within the pellet was observed. The crushing resistance for as received fibre reinforced pellets (bulk density 452 kg/m³) was 3.0 MPa corresponding to an increase in strength of 140%. The enhanced strength was also confirmed by the single pellet compression test.