数字信号处理器DSP主控GMAW焊接

阐述了焊接过程信息数字处理控制思想，实际研究了数字信号处理器9DSP）在CO2气体保护焊机中的应用，将数字信号处理器（DSP）在送丝系统的柔性化调节，引弧和收弧模式，焊接参数的一元化自调节等方面的应用作了研究和试验，通过研究和样机试验，建立了一套焊接电源的数字化，信息化，柔性化控制平台，并探讨了数字信号处理器（DSP）在CO2焊接领域中的应用优点和前景，并提出了DSP主控GMAW焊接电源全系统框图，试验证明该系统工作稳定可靠，较好地满足了工艺性能，实现了焊机控制的数字化。     

不同焊接方法对哈氏合金C-276焊缝组织和耐晶间腐蚀性能的影响

采用ASTM-G28B法进行晶间腐蚀试验,分别研究了手工GTAW和手工GMAW对哈氏合金C-276焊缝组织和耐晶间腐蚀性能的影响。结果表明,手工GMAW焊接的C-276合金,焊缝区析出碳化物第二相较多,晶间腐蚀倾向更大。     

Welding current and arc voltage control in a GMAW process using ARMarkov based MPC

A predictive functional controller based on ARMarkov model structure has been designed to control welding current and arc voltage in a GMAW process. The closed loop system performance is investigated through computer simulations and is compared by those achieved from implementing two commonly used controllers i.e. PI and feedback linearization based PID. The local stability of the closed loop system is analyzed in the presence of uncertainties in the linearized model of the process as well as the control parameters. Finally it is shown that the proposed controller performs like a PI controller along with a pre-filter compensator.     

混合气体在熔化极气体保护焊中的应用

熔化极气体保护焊(GMAW)是焊接生产中常用的焊接方法之一.阐述了混合气体在熔化极气体保护焊中的应用现状,分析了保护气体成分的不同配比对熔化极气体保护焊的焊接工艺性能、焊接质量的影响.     

Fluxless arc weld-brazing of aluminium alloy to steel

In this work, joining of aluminium alloy AA6061-T6 to Interstitial Free steel using pulsed gas metal arc welding process has been attempted. The effect of different surface conditions of steel (viz, galvanized, galvanealed and uncoated) and gap between the sheets on braze joint formation have been investigated. Galvanized steel surface showed good bead width, joint formation and lap shear strength compared to the other two combinations. Interface gap has not affected the wetting behaviour significantly but presence of a gap of 300 μm or so helped in escape of zinc vapour during the process there by avoiding formation of any crevice or macroporosity in the joint. Features and properties of the joint are characterized by metallography, fractography, energy dispersive spectroscopy (EDS) and lap shear tests. Load carrying capacity of Al-Galvanized steel was highest (222 N/mm of seam length) compared to other combinations, aided by better wetting due to presence of Zn on the surface and minimum porosity due to interfacial gap provided during brazing.     

基于新型控制法的逆变GMAW工艺特点

随着熔化极气体保护焊的应用与推广,那些以飞溅小和成形好为特点的通用型焊机常常不能适应新的环境和要求,如西气东输中的管道打底焊、集装箱的高速焊、汽车制造中的短焊缝焊接、角焊缝的尺寸控制和狭窄空间的熔深控制等,还有超薄板焊接、双脉冲焊、双丝高速焊、TIME高效焊和磁控MAG焊等,这些具有特殊功能的焊接方法,我们称为个性化焊接.这些个性化焊接方法均具有自己的工艺特点,并能完成一些特殊的焊接要求.可见这些个性化焊接方法必将成为GMAW推广应用的新的增长点.     

A scientific application oriented classification for metal transfer modes in GMA welding

In this work, metal transfer in solid wire GMA welding was studied. Several experiments with different combinations of gas-wire-parameters were carried out to observe metal transfer and to characterize the various transfer modes. A laser shadograph system with synchronized electrical signals and high speed filming were used. New modes were observed and their particular characteristics described for completeness. A classification for metal transfer, oriented to scientific personnel (researchers, scholars and students), is proposed, in which the modes are independent of the type of shielding gas or welding power source.     

水口电站4#机转轮室里衬裂纹的修复

单机容量世界最大的我国福建水口电站轴流转桨式水轮发电机组，其中4＃机组由于长期偏离原设计工况运行，致使其转轮室钢板里衬产生了严重裂纹。采用熔化极气体保护焊方法，于2002年1月末将其修复正常。     

焊丝中Si元素含量对铝合金接头裂纹敏感性的影响规律及机理

使用扫描电镜、能谱、温度场实时采集等测试方法,研究了焊丝中Si含量对AA6063铝合金GMAW焊接头热裂纹敏感性的影响规律及机理. 结果表明,当焊丝为纯铝时,鱼骨试样的焊缝中心会出现细长的焊接裂纹;当焊丝中的Si含量为4.5% ~ 6%时,裂纹的长度变短,但是开裂距离明显增加;当焊丝中的Si含量达到11% ~ 13%时,试样焊缝无裂纹出现. 随着Si含量的不断提高,合金易出现裂纹的凝固温度区间先增大后减小;焊丝中Si含量的不同还会影响凝固后期金属液的流动性,使得焊缝晶界处的物相成分和形态都有明显的区别;同时,Si含量的提高会使得接头的冷却速度先增加后减小,从而导致应力状态改变,热裂纹敏感性先升高后降低.