Model Validation for Bridge-Road-Vehicle Dynamic Interaction System

The dynamic response of highway bridges subjected to moving truckloads has been observed to be dependent on (1) dynamic characteristics of the bridge; (2) truck configuration, speed, and lane position on the bridge; and (3) road surface roughness profile of the bridge and its approach. Historically, truckloads were measured to determine the load spectra for girder bridges. However, truckload measurements are either made for a short period of time [for example, weigh-in-motion (WIM) data] or are statistically biased (for example, weigh stations) and cost prohibitive. The objective of this paper is to present results of a 3D computer-based model for the simulation of multiple trucks on girder bridges. The model is based on the grillage approach and is applied to four steel girder bridges tested under normal truck traffic. Actual truckload data collected using a discrete bridge WIM system are used in the model. The data include axle loads, truck gross weight, axle configuration, and statistical data on multiple presence (side by side or following). The results are presented as a function of the static and dynamic stresses in each girder and compared with code provisions for dynamic load factor. The study provides an alternate method for the development of live-load models for bridge design and evaluation.     

Evaluation of Effective Width and Distribution Factors for GFRP Bridge Decks Supported on Steel Girders

Glass fiber-reinforced polymer (GFRP) bridge deck systems offer an attractive alternative to concrete decks, particularly for bridge rehabilitation projects. Current design practice treats GFRP deck systems in a manner similar to concrete decks, but the results of this study indicate that this approach may lead to nonconservative bridge girder designs. Results from a number of in situ load tests of three steel girder bridges having the same GFRP deck system are used to determine the degree of composite action that may be developed and the transverse distribution of wheel loads that may be assumed for such structures. Results from this work indicate that appropriately conservative design values may be found by assuming no composite action between a GFRP deck and steel girder and using the lever rule to determine transverse load distribution. Additionally, when used to replace an existing concrete deck, the lighter GFRP deck will likely result in lower total stresses in the supporting girders, although, due to the decreased effective width and increased distribution factors, the live-load-induced stress range is likely to be increased. Thus, existing fatigue-prone details may become a concern and require additional attention in design.     

Simplified Moment Redistribution of Hybrid HPS 485W Bridge Girders in Negative Bending

Simplified moment redistribution procedures based on shakedown have recently been approved by AASHTO LRFD Bridge Design Specifications (AASHTO 2004). These procedures are currently only applicable for homogeneous girders, and thus, the objective of this study is to evaluate whether these procedures can be further applied for hybrid HPS 485W girders. A parametric study is carried out using validated three-dimensional finite-element (FE) analyses to study the inelastic behavior of hybrid HPS 485W girders in negative bending for this purpose. The effective plastic moments obtained from the FE studies are compared with those from the proposed prediction equations, where good correlation is observed. A design example of a three-span slab-on-girder bridge with hybrid HPS 485W girders using both elastic design and the simplified moment redistribution procedures is also presented, where it is shown that the use of moment redistribution procedures results in a negative bending section that is 13% lighter than the corresponding elastic design.     

AASHTO-LRFD Live Load Distribution for Beam-and-Slab Bridges: Limitations and Applicability

This paper presents a comparison between the live load distribution factors of simple span slab-on-girders concrete bridges based on the current AASHTO-LRFD and finite-element analysis. In this comparison, the range of applicability limits specified by the current AASHTO-LRFD is fully covered and investigated in terms of span length, slab thickness, girder spacing and longitudinal stiffness. All the AASHTO-PCI concrete girders (Types I–VI) are considered to cover the complete range of longitudinal stiffness specified in the AASHTO-LRFD. Several finite-elements linear elastic models were investigated to obtain the most accurate method to represent the bridge superstructure. The bridge deck was modeled as four-node quadrilateral shell elements, whereas the girders were modeled using two-node space frame elements. The live load used in the analysis is the vehicular load plus the standard lane load as specified by AASHTO-LRFD. The live load is positioned at the longitudinal location that produced the extreme effect, and then it is moved transversely across the bridge width in order to investigate all possibilities of one-lane, two-lane and three-lane design loads. A total of 886 bridge superstructure models were built and analyzed using the computer program SAP2000 to perform this comparison. The results of this study are presented in terms of figures to be practically useful to bridge engineers. This study showed that the AASHTO-LRFD may significantly overestimate the live load distribution factors compared to the finite-element analysis.     

Repair of Damaged Steel-Concrete Composite Girders Using Carbon Fiber-Reinforced Polymer Sheets

The aging infrastructure of the United States requires significant attention for developing new materials and techniques to effectively and economically revive this aging system. Damaged steel-concrete composite girders can be repaired and retrofitted by epoxy bonding carbon fiber-reinforced polymer (CFRP) laminates to the critical areas of tension flanges. This paper presents the results of a study on the behavior of damaged steel-concrete composite girders repaired with CFRP sheets under static loading. A total of three large-scale composite girders made of W355×13.6 A36 steel sections and 75-mm-thick by 910-mm-wide concrete slabs were prepared and tested. One, three, and five layers of CFRP sheet were used to repair the specimen with 25, 50, and 100% loss of the cross-sectional area of their tension flange, respectively. The test results showed that epoxy bonded CFRP sheet could restore the ultimate load-carrying capacity and stiffness of damaged steel-concrete composite girders. Comparison of the experimental and analytical results revealed that the traditional methods of analysis of composite beams were conservative.     

Local Effects Induced by Longitudinal Forces in Composite Girders

Local effects on the shear connection of composite girders induced by longitudinal actions such as the anchorages of prestressing cables, concrete shrinkage, or a uniform thermal action on the slab are analyzed. Closed-form solutions are obtained by using the simple model of a composite beam with a linearly elastic shear connection. Successively, by considering the limit scheme of an infinitely long beam, very simple formulas are derived permitting evaluation of the peak value and extension of the interface shear force distribution induced by the longitudinal actions. Numerical applications are carried out to show the effectiveness of the proposed formulas for a wide range of the shear connection stiffness and for longitudinal forces applied both along the beam axis and at the beam end.     

Reliability validation of multigirder steel bridges designed by LRFD

The reliability index is examined for steel girder highway bridges designed by AASHTO load and resistance factor design (LRFD) Strength I limit state. The reliability analysis is based on the extensive stochastic finite element method (SFEM). The SFEM takes advantages of the conventional advanced first-order second-moment in that it considers the mechanic connection between the critical member and other members in the whole structure. The bridges are modeled as grillage beam systems. Basic design variables include sectional properties and various dead and live loads. The results obtained in noncomposite steel bridges indicate that the reliability index is very sensitive to the lateral distribution of live loads. Consequently, a simplified method is used in the reliability analysis of composite steel bridges. This simplified method can avoid the complex computation in SFEM yet achieve good accuracy. Due to overestimating the lateral distribution of live loads, the Strength I limit state in AASHTO LRFD specifications results in a conservative design for flexure but not for shear.     

Theoretical Evaluation of Flange Local Buckling for Horizontally Curved I-Girders

Curvature greatly complicates the behavior of horizontally curved steel plate girders used in bridge superstructures. The warping stress gradient across the width of I-girder flange plates reduces the vertical bending stress at which the flange plate buckles. The 2007 AASHTO Load and Resistance Factor Design Specifications eliminate the shortcomings of the 2003 AASHTO Guide Specifications for Horizontally Curved Bridges by unifying the flexural design of tangent and curved I-girder bridges. This paper evaluates flange local buckling resistance based upon theoretical and analytical models that consider the effect of stress gradient across the flange coupled with the influence of rotational resistance provided by the web. The developed equations are verified using the finite element method, and the potential impact is demonstrated using the design example presented in the Guide Specifications.     

Development of an Efficient Connector System for Fiber Reinforced Polymer Bridge Decks to Steel Girders

This paper discusses the development of an innovative and efficient connector to be used with fiber reinforced polymer (FRP) decks supported by steel girders. A summary is provided detailing various proprietary connectors currently employed by FRP deck manufacturers. The paper then describes the development and experimental testing of a clamped shear stud-type connector. Experimental testing was conducted in two phases. The first phase consisted of individual connector testing. In this phase, several variations of the connector are tested and evaluated for strength, damage development, and overall performance. Results of this phase of testing are used to select a final connection design to be used in the second phase of testing, which consisted of testing a scale model bridge that incorporates several of the proposed connectors. The bridge is subjected to static load tests and the resulting reactions and deflections from these tests are compared with comprehensive finite element models of the system.     

Repair of Steel Composite Beams with Carbon Fiber-Reinforced Polymer Plates

One significant cause of deterioration of steel bridge structures is the corrosion due to extensive use of deicing salts in winter weather. The investigation presented in this paper focused on the behavior of steel composite beams damaged intentionally at their tension flange to simulate corrosion and then repaired with carbon fiber-reinforced polymer (CFRP) plates attached to their tension areas side. Damage to the beams was induced by removing part of the bottom flange, which was varied between no damage and loss of 75% of the bottom flange. All beams were tested to failure to observe their behavior in the elastic, inelastic, and ultimate states. To help implement this strengthening technique, a nonlinear analytical procedure was also developed to predict the behavior of the section/member in the elastic, inelastic, and ultimate states. The test results showed a significant increase in the strength and stiffness of the repaired beams. Through the use of CFRP plates, all damaged beams were fully restored to their original (undamaged state) strength.