Study of Pb-based and Pb-free perovskite solar cells using Cu-doped Ni1-xO thin films as hole transport material

SCAPS solar cell simulation program was applied to model an inverted structure of perovskite solar cells using Cu-doped Ni_1-xO thin films as hole transport layer. The Cu-doped Ni_1-xO film were made by co-sputtering deposition under different deposition conditions. By increasing the amount of the Cu-dopant, the film crystallinity enhanced whereas the bandgap energy decreased. The transmittance of the thin films decreased significantly by increasing the sputtering power of copper. High quality, uniform, compact, and pin-hole free films with low surface roughness were achieved. The structural, chemical, surface morphology, optical, electrical, and electronic properties of the Cu doped Ni_1-xO films were used as input parameters in the simulation of Pb-based (MAPbI_3-xCl_x) and Pb-free (MAGeI₃) perovskite solar cells. Simulation results showed that the performance of both Pb-based and Pb-free perovskite solar cell devices significantly enhanced with Cu-doped Ni_1-xO film. The highest power conversion efficiency (PCE) for the Pb-free perovskite solar cell is 8.9% which is lower than the highest PCE of 17.5% for the Pb-based perovskite solar cell.     

Electroactive polymers containing 3-arylcarbazolyl units as hole transporting materials for OLEDs

Monomers and their polymers containing 3-arylcarbazolyl electrophores have been synthesized by the multi-step synthetic route. The materials were characterized by thermo-gravimetric analysis, differential scanning calorimetry and electron photoemission technique. The polymers represent materials of high thermal stability having initial thermal degradation temperatures in the range of 331–411 °C. The glass transition temperatures of the amorphous polymeric materials were in the rage of 148–175 °C. The electron photoemission spectra of thin layers of monomers showed ionization potentials in the range of 5.6–5.65 eV. Hole-transporting properties of the polymers were tested in the structures of organic light emitting diodes with Alq₃ as the green emitter. The device containing hole-transporting layers of polyether with 3-naphthylcarbazolyl groups exhibited the best overall performance with a maximum current efficiency of 3.3 cd/A and maximum brightness of about 1000 cd/m².     

中原油田深井大井眼段钻井液工艺

濮深8井是中原油田在西部洼陷南部寻找接替储量的一口重点深探井,也是中原油田第一口井深达6000m的超深井。分析了濮深8井钻井液的配备及维护和处理技术,得出深井大井眼段钻井液工艺技术存在以下问题:井眼大,钻井液量及钻屑量多,处理时间长,处理剂用量多,处理频繁;返速低使钻井液清洗井眼的能力减弱;井下温度高使处理剂的作用明显降低,二氧化碳的侵入使钻井液性能变差。钻井液维护处理的较好方法是定时、定量补充处理剂胶液。固相控制是深井大井眼段钻井液工艺中的关键问题,必须配套并且有效地使用固控设备,以维护好钻井液性能。     

裂隙岩体中掏槽爆破的影响因素分析

对裂隙岩体中掏糟爆破布孔的影响因素进行了研究，并根据裂分布的情况提出相应的布孔方法和原则。对有关的工程施工具有实际意义。     

复合PDC钻头在桩西地区定向井中的应用

PDC钻头在胜利油田桩西地区的成功应用，大大地提高了该地区的机械钻速。但由于PDC钻头在结构与钻进参数上的特殊性，造成了其在定向井中井眼轨迹控制方面的难度。总结PDC钻头在桩西地区定向井中应用所表现出的部分规律，提出了在该地区采用PDC钻头的改进技术，并介绍了典型的成功实例。     

二氧化碳对油井水泥石的腐蚀及其防护措施

在湿环境下,油气构造中富含的CO_2对水泥石产生碳化腐蚀,碳化结果使水泥石渗透率变大、抗压强度减小,诱发流体窜流、塑性地层井壁垮塌等事故,造成巨大的经济损失。介绍了在不同温度下的水泥水化产物及其碳化产物。从化学角度分析了CO_2在不同温度下对油井水泥环碳化腐蚀的机理、影响因素及防护措施。在低于110℃的温室下,CO_2的腐蚀速度受扩散控制,其影响因素包括水泥浆密度和水泥石渗透率及水泥石孔隙液中Ca(OH)_2的含量,在水泥中掺加活性硅灰或提高水泥浆密度可预防碳化腐蚀。在大于110℃的高温下,碳化腐蚀速度受水泥水化产物中Ca(OH)_2含量和水泥石碳化后渗透率大小的影响。正确的防腐工艺是在水泥石中加入10％—15％的石英砂,或者在纯水泥中加3％—8％的膨润土。     

δ掺杂样品中空穴态的新行为

用有效质量理论研究了δ掺杂势中电子和空穴的行为。发现能量接近于δ势垒峰的空穴穿越势垒时能产生一系列谐振态。这些状态中的空穴波函数汇聚在势垒峰周围而同量子限制在势阱中的电子波函数交叠,产生光跃迁。用MBE生长的δ掺杂样品进行光调制光谱测量,发现明显的带间跃迁峰。测得的光谱峰同理论计算的能级相吻合,证实了δ势垒中空穴的新行为。     

煤层防塌钻井液技术

从煤层岩的强度等力学性能和化学结构、密度、亲油亲水性等理化性能综合分析了塔里木盆地依奇克里克区块煤层坍塌的机理，确定了防塌措施，用封堵实验法考查了粒径、温度、封堵剂种类与加量等因素对钻井液封堵防塌性能的影响，优选出的煤层防塌钻井液技术配方，在依西-1井、依南-4井等井的现场应用中取得了较好的煤层防塌效果，井径规则，起下钻，电测，取心，下套管，固井作业均顺利。     

Bright Blue Light—emitting Diodes Based on a Novel Fluorescent Dye Containing Heterocyclic Groups

Novel molecular material ,1-benzothiazoly-3-pheny1-pyrazoline (BTPP) was found to function as bright blue light emitting dye in organic electroluminescent device, and its optical and electric characteristics were investigated. This heterovyclic compound exhibited good characteristics of blue photoluminescence and electroluminescence,which had the emission peak at 450nm .The single layer light-emitting devices using BTPP as light -emitting material dispersed in poly(N-vinylcarbazole)(PVK) and double layer ones using PBD as hole block layer above the light-emitting layer were fabricated using conventional spin-casting and vaccum vapour deposition methods. The introduction of PBD has enhanced electron injection and luminance efficiency, compared with the single layer LEDs.     

High‐Tg Carbazole Derivatives as Blue‐Emitting Hole‐Transporting Materials for Electroluminescent Devices

A series of dicarbazolyl derivatives bridged by various aromatic spacers and decorated with peripheral diarylamines were synthesized using Ullmann and Pd‐catalyzed C–N coupling procedures. These derivatives emit blue light in solution. In general, they possess high glass‐transition temperatures (T_g > 125 °C) which vary with the bridging segment and methyl substitution on the peripheral amine. Double‐layer organic light‐emitting devices were successfully fabricated using these molecules as hole‐transporting and emitting materials. Devices of the configuration ITO/HTL/TPBI/Mg:Ag (ITO: indium tin oxide; HTL: hole‐transporting layer; TPBI: 1,3,5‐tris(N‐phenylbenzimidazol‐2‐yl)benzene) display blue emission from the HTL layer. The EL spectra of these devices appear slightly distorted due to the exciplex formation at the interfaces. However, for the devices of the configuration ITO/HTL/Alq₃/Mg:Ag (Alq₃ = tris(8‐hydroxyquinoline)aluminum) a bright green light from the Alq₃ layer was observed. This clearly demonstrates the facile hole‐transporting property of the materials described here.