Effect of Structural Parameters on the Thermal Stress of a NiFe2O4-Based Cermet Inert Anode in Aluminum Electrolysis

Inert anode has been a hot issue in the aluminum industry for many decades. With the help of FEA(finite element analysis) software ANSYS,a model was developed to simulate the thermal stress distribution working condition of an inert anode. To reduce its thermal stress,the effect of some parameters on the thermal stress distribution was investigated,including the anode height,the anode radius,the hole depth,the hole radius,and the radius of inner chamfer and outer chamfer. The results showed that in the actual working condition of an inert anode,there existed a large axial tensile stress near the tangent interface between the anode and bath,which was the major cause of anode breaking. Increasing the anode height and reducing the hole depth properly seemed to be beneficial for the stress distribution. With the increase of anode radius,the stress distribution became better first and then deteriorated,the reasonable value was between 0.045 to 0.06m. The hole radius had a significant effect on the stress and a smaller radius would reduce the thermal stress. The effect of the radius of the inner chamfer and the outer chamfer was less than other parameters.     

Effect of thermal treatment of wood lumbers on their adhesive bond strength and durability

Wood used in outdoor applications needs to undergo either chemical or thermal treatment to improve its decay resistance. Thermal treatment permits to avoid the use of toxic chemicals, increases the dimensional stability and gives a dark color to the wood. However, this process deteriorates the mechanical properties of wood, i.e., the wood becomes more fragile and rigid. The chemical transformation of wood that takes place during the heat treatment changes the interaction between the wood surface and the adhesive. In this work, the interfacial bonding strength (the resistance to the shear stress by compression in parallel direction to the glued interface) and cyclic delamination (resistance to delamination during accelerated exposure) for different wood species and adhesives were tested in accordance with the ASTM D2559 standard. Four wood species: scott pine (Pinus sylvestris), aspen (Populus tremuloides), yellow poplar (Liriodendron tulipifera) and jack pine (Pinus banksiana) both treated and non-treated, and two structural adhesives, phenol resorcinol formaldehyde (PRF) and polyurethane (PUR), were used in the testing. Among the studied species, jack pine is found to be the easiest to bond, while aspen is found to be the most difficult. With the wood species and adhesives evaluated in this study, non-treated wood is found to provide a better bonding strength than the treated wood.     

Study of effect of aging on martensitic transformation and tribological properties of TiNi alloy using DSC,neutron diffraction,and micromechanical probing techniques

Abstract

Recent studies have demonstrated that TiNi shape memory alloy exhibits excellent wear resistance, benefiting from their pseudoelasticity (PE) due to a thermoelastic martensitic transformation. The maximum wear resistance of the alloys corresponds to an optimum balance between the PE and hardness, which is strongly influenced by heat treatment. In this work, the effect of aging treatment on martenstic transformation behaviour, mechanical properties, including the pseudoelasticity and hardness, and wear behaviour of a Ti–51 at.-%Ni alloy was investigated using differential scanning calorimetry, neutron diffraction, and micromechanical probing techniques. The main objective of the study was to understand the aging effect on wear behaviour of the TiNi alloy and explore the mechanisms involved for further improvement of this novel tribo-alloy.     

Coupled heat and fluid flow model and experimental verification of aluminium plate die casting

Abstract

The present work aims to forecast mould filling, void shape, location and size as well as columnar to equiaxed transition (CET) in commercial pure aluminium casting. A model coupling the momentum equations of the fluid flow and heat transfer equations is presented, in which metallostatic pressure, air gap and oxide layer are considered. Different casting parameters were investigated such as casting configuration by varying the plate thickness from 5 to 20 mm, melt superheat from 40 to 120°C, mould preheat up to 200°C and different pouring heads ranging from 0·3 to 0·6 m. Regarding the microstructure and void formation, the approach based on the Niyama criterion, was considered. The experimental verification of the model was achieved by gravity die casting in the form of a rectangular cavity. Voids inside aluminium plate were investigated by X-ray imaging. Microstructure and CET was investigated microscopically. The supposed model proves its validity for mould filling and in detecting the void features and CET.     

Multipass rolling of aluminium alloys: finite element simulations and microstructural evolution

Abstract

Use of numerical predictive methods such as finite element analysis is becoming progressively more common for modelling industrial hot metal working and forming processes. These tools are used not only to predict the thermomechanical behaviour of metals but increasingly to predict microstructural changes by linking them to physical models of recrystallisation and textural evolution. This paper describes the development and application of a fully integrated model for the prediction of thermomechanical and microstructural behaviour during multipass hot rolling of aluminium alloy AA 3104. Finite element code ABAQUS/standard has been used in the work and the process is modelled assuming plane strain conditions. It is shown that for this alloy the static recrystallisation which occurs during interpass cooling does not significantly influence the thermomechanical response during subsequent rolling passes.     

Effect of ZnO coating of whiskers on thermal expansion properties of aluminium borate whisker reinforced aluminium composites

Abstract

The pure aluminium composites reinforced by ZnO coated aluminium borate whiskers were fabricated by squeeze casting. The microstructure of the composite was observed using an optical microscope and the thermal expansion behaviours of the composites were investigated in the range from 50 to 400°C. In addition, the effects of heat treatment and thermal cycling on the thermal expansion behaviours of the composite were also investigated. The results show that the coefficient of thermal expansion of as cast composites decreases with the ZnO coating content increasing. However, heat treatment time and thermal cycling lead to an increase in the CTE of the composite.     

Dynamic strain aging effects in niobium microalloyed steel

Abstract

The dynamic strain aging behaviour of a niobium microalloyed steel has been examined. Hot tensile testing was carried out on heat treated and as received specimens. Heat treated specimens were austenitised at 1000°C for 1 h, and then cooled in air or in a stainless steel cylinder to obtain various amounts of free or uncombined interstitial solutes in solid solution, to examine the effect on the dynamic strain aging behaviour of the steel. It was found that dynamic strain aging takes place in niobium microalloyed steel during tensile testing at temperatures ranging from ambient temperature to 450°C at a crosshead displacement rate of 2 mm min^-1. As a result, the ultimate tensile strength and initial work hardening rate exhibit maximum values at temperatures between 200 and 350°C. Also, load-extension graphs for tested specimens show serrated behaviour and yield points at 200, 250, and 300°C. It is believed that dynamic strain aging in niobium steel is caused by interaction between dislocations and interstitial solutes (nitrogen and carbon) or solute pairs consisting of one interstitial and one substitutional solute atom (for example Mn-C and Mn-N).     

Measurement of autoclave thermal profiles during high pressure steam de-waxing of investment shells Part 1 - Vessel profiles

Abstract

Investment casting research is being carried out by the University of Birmingham, sponsored by EPSRC and a consortium of industrial companies. The programme is aimed at developing a fundamental understanding of the process, with a view to routinely producing sound, net shape castings. A key stage within the investment process is that involving the removal of wax from the unfired ceramic shell. This important process is carried out within the confines of a sealed pressure vessel, more commonly referred to as a Boilerclave*, with external pressure gauges as the only indication of what is actually happening inside the cavity. To metaphorically 'see' inside the vessel would allow the factors controlling de-wax to be characterised and controlled. This paper contains results obtained at The University of Birmingham using a specially instrumented steam autoclave that allows visual data capture, thermal and steam pressure profiles within the chamber, and thermal instrumentation of waxes and shells to be obtained. Results of thermal and pressure profiles inside the vessel body are presented and implications of these results upon the mechanism of wax removal and the effect upon ceramic shells are discussed.     

Friction stir welding of aluminium 7136-T76511 extrusions

Abstract

This research programme evaluates the as welded properties of Al 7136-T76511 extrusions joined through friction stir welding (FSW). Microstructural characterisation and mechanical testing were performed on the baseline material and on panels friction stir welded at 250 and 350 rev min^–1 (all other weld parameters held constant). Transmission electron microscopy revealed the microstructural features in each of the unique weld regions and demonstrated that the precipitate density and morphology in these regions correlates with the temperature profile produced by the FSW process. A thermal model of FSW is developed that utilises an energy based scaling factor to account for tool slip. The slip factor is derived from an empirical relationship between the ratio of the maximum welding temperature to the solidus temperature and energy per unit length of weld. The thermal model successfully predicts the maximum welding temperatures and profiles over a range of energy levels. The mechanical behaviour after welding is correlated to the temperature distribution predicted by the model and to the observed microstructural characteristics. As welded mechanical properties of the alloy trended positively with the energy per unit length of weld, i.e. the highest joint efficiency was achieved at the highest welding temperature.