Effect of heat treatment and zircon addition on the properties of low-cement castables based on recycled alumina grog

In this investigation, low-cement castables were prepared using 70% alumina grog aggregates obtained from crushed alumina brick waste. The aggregates were thermally treated at 1550 °C for 3 h. Four types of low-cement castables were prepared with various types of aggregates (alumina grog with or without thermal treatment) and fillers (with or without zircon addition), and they were evaluated in terms of their physical, thermal, and chemical properties. Microstructural analysis via scanning electron microscopy (SEM) was performed on the castables before and after slag attack. Compared to the other fabricated castables, the thermally treated alumina grog castables with zircon showed better physical properties, such as a higher bulk density, cold crushing strength, and modulus of rupture and a lower apparent porosity and water absorption. In addition, they had a higher positive linear thermal expansion, refractoriness under load, permanent linear change, and hot modulus of rupture. The results of the SEM with energy dispersive X-ray analysis of the prepared castables confirmed that the mullite and anorthite phases were predominant when zircon was not added and the zircon–mullite phase additionally appeared upon the incorporation of zircon. A quantitative elemental analysis via X-ray fluorescence spectroscopy was employed to determine the composition of the castables. X-ray diffraction analysis showed that the alumina grog castables had a high mullite and low anorthite content, and the thermally treated alumina grog had a high anorthite, low mullite, and high zircon content. The improvement in the mechanical and thermo-mechanical properties of the castables with thermally treated alumina grog and added zircon can be attributed to the formation of the zircon–mullite phase with a low mullite phase content.     

Effect of partial replacement of geopolymer binder materials on the fresh and mechanical properties: A review

The growth of demand for concrete raises concerns about the consumption of natural resources and ordinary Portland cement. Geopolymer composites show promise as a sustainable alternative for conventional cement concrete. Considering the wide range of potential geopolymer composites applications (including suitability for transportation infrastructure, underwater applications, repair and rehabilitation of structures as well as recent developments in 3D printing), the desired fresh and mechanical properties of the geopolymer composite may vary between applications: for example, rapid setting can be a merit for certain applications and a demerit for others. Therefore, the desired fresh and mechanical properties (e.g., workability, setting time, compressive strength, etc.) can be controlled for a given geopolymer source material through its partial substitution by natural or by-product materials. Recognizing the critical role of various replacement materials in enhancing the potential applications of geopolymer composites, the present review was undertaken to quantify and understand the effect of partial replacement by fly ash, metakaolin, kaolin, red mud, slag, ordinary Portland cement, and silica fume on the setting time, workability, compressive strength and flexural strength of various source materials addressed in the literature. The review also provides insights into research gaps in the field to promote future research.     

物理化学课程的创新教学模式研究及其效果分析

物理化学课程创新教学模式是以学生学习为中心,吐故纳新,优化精选,以新颖或变化的教学方式进行教学。调查表明创新教学模式受到绝大多数学生的肯定和认可,有效地调动学生的积极性,提高了学生对物理化学的学习和探究兴趣,学生提问问题的广度和难度发生显著变化。该教学模式能够逐步提升学生的创新意识和创新能力。     

Corrosion resistance of Al–Cr-slag containing chromium–corundum refractories to slags with different basicity

Al–Cr slag is the solid waste generated by the smelting of Cr metal. It presents a range of environmental hazards. This study addressed the corrosion resistance of Al–Cr slag containing chromium–corundum refractories to slags with different basicity. Herein, we provide suggestions for the use of Cr–corundum of different basicity in kilns. Al–Cr slag, brown fused Al₂O₃, and chrome green were used as the raw materials, with pure calcium aluminate cement being used as a binder. The brick samples, prepared using different blends of chrome green and corundum, were fired at 1600?°C, and subsequently subjected to a slag corrosion test. After corrosion by slag of different basicity, the phase composition and microstructure of the sample were analyzed by X-ray diffraction, energy dispersive spectrometer and scanning electron microscopy. There were two major findings. First, Cr–corundum brick made from Al–Cr slag has a better slag corrosion resistance than that made from Cr₂O₃ and brown fused Al₂O₃. Second, Cr–corundum brick made from Al–Cr slag has superior corrosion resistance to slag with a CaO:SiO₂ ratio of 2:1.     

用ASP进行化学课堂在线测试、自动阅卷、分析统计

针对化学学科特点。使用ASP进行在线网络测试、自动阅卷、分析统计的方法。     

Numerical modeling of combustion processes and pollutant formations in direct-injection diesel engines

The Representative Interactive Flamelet (RIF) concept has been applied to numerically simulate the combustion processes and pollutant formation in the direct injection diesel engine. Due to the ability for interactively describing the transient behaviors of local flame structures with CFD solver, the RIF concept has the capabilities to predict the auto-ignition and subsequent flame propagation in the diesel engine combustion chamber as well as to effectively account for the detailed mechanisms of soot formation, NO_X formation including thermal NO path, prompt and nitrous NO_X formation, and reburning process. Special emphasis is given to the turbulent combustion model which properly accounts for vaporization effects on the mixture fraction fluctuations and the pdf model. The results of numerical modeling using the RIF concept are compared with experimental data and with numerical results of the commonly applied procedure which the low-temperature and high-temperature oxidation processes are represented by the Shell ignition model and the eddy dissipation model, respectively. Numerical results indicate that the RIF approach including the vaporization effect on turbulent spray combustion process successfully predicts the ignition delay time and location as well as the pollutant formation.     

Synthesis of chemically and structurally modified dicalcium silicate

This paper describes the synthesis of cements, chemically and structurally related to Ca₂SiO₄. Silica was obtained from rice hull after heating at 600 °C. Calcium oxide and small amounts of barium chloride were mixed in order to obtain a final (Ca/Si) or (Ca+Ba)/Si ratio equal to 1.95, 1.90, and 1.80, which is lower than in the conventional cement. The solids were mixed and ultrasonically treated for 1 h with a water/solid ratio of about 20. After drying and grinding, the mixtures were heated up to 1100 °C. It was possible, in some cases, to obtain a cementitious material. These cements are structurally related to β-Ca₂SiO₄ and the lower (Ca+Ba)/Si ratio obtained was 1.95. The initial chemical compositions of these cements are: (Ca_1.83+Ba_0.12)SiO₄ and (Ca_1.79+Ba_0.16)SiO₄. A further lowering in the (Ca+Ba)/Si ratio changes the nature of the silicates.     

分析再热器超温爆漏与水冷壁结焦控制量的关系

文章介绍了宝钢自备电厂在改善锅炉燃烧工况，控制锅炉水冷壁结焦所采取的技术措施，分析了锅炉水冷壁结焦量与锅炉二次再热器烟气出口平均温度的关系，为解决锅炉水冷壁结焦所引发的二次再热器超温爆漏问题提供了依据。     

A Study of Ozone Generation by Negative Corona Discharge Through Different Plasma Chemistry Models

The Steady radial distribution of chemical species in a wire‐to‐cylinder ozone generator filled with pure oxygen has been computed by applying four different plasma chemistry models of increasing complexity. The most complete model considers ten species (e, O₂ ⁺, O₂ ^?, O₃ ^?, O^?, O₂, O₂(¹Δ_g), O₂(¹∑_g ⁺), O and O₃) and 79 reactions, including ionization by electron impact, electron attachment and detachment, electron-ion recombination, charge transfer, etc. The chemical model is coupled with the electrical model through Poisson's equation. The spatially averaged ozone density has been computed as a function of the current intensity and compared with the experimental values obtained by UV spectroscopy.