Effect of heat treatment and zircon addition on the properties of low-cement castables based on recycled alumina grog

In this investigation, low-cement castables were prepared using 70% alumina grog aggregates obtained from crushed alumina brick waste. The aggregates were thermally treated at 1550 °C for 3 h. Four types of low-cement castables were prepared with various types of aggregates (alumina grog with or without thermal treatment) and fillers (with or without zircon addition), and they were evaluated in terms of their physical, thermal, and chemical properties. Microstructural analysis via scanning electron microscopy (SEM) was performed on the castables before and after slag attack. Compared to the other fabricated castables, the thermally treated alumina grog castables with zircon showed better physical properties, such as a higher bulk density, cold crushing strength, and modulus of rupture and a lower apparent porosity and water absorption. In addition, they had a higher positive linear thermal expansion, refractoriness under load, permanent linear change, and hot modulus of rupture. The results of the SEM with energy dispersive X-ray analysis of the prepared castables confirmed that the mullite and anorthite phases were predominant when zircon was not added and the zircon–mullite phase additionally appeared upon the incorporation of zircon. A quantitative elemental analysis via X-ray fluorescence spectroscopy was employed to determine the composition of the castables. X-ray diffraction analysis showed that the alumina grog castables had a high mullite and low anorthite content, and the thermally treated alumina grog had a high anorthite, low mullite, and high zircon content. The improvement in the mechanical and thermo-mechanical properties of the castables with thermally treated alumina grog and added zircon can be attributed to the formation of the zircon–mullite phase with a low mullite phase content.     

Effect of partial replacement of geopolymer binder materials on the fresh and mechanical properties: A review

The growth of demand for concrete raises concerns about the consumption of natural resources and ordinary Portland cement. Geopolymer composites show promise as a sustainable alternative for conventional cement concrete. Considering the wide range of potential geopolymer composites applications (including suitability for transportation infrastructure, underwater applications, repair and rehabilitation of structures as well as recent developments in 3D printing), the desired fresh and mechanical properties of the geopolymer composite may vary between applications: for example, rapid setting can be a merit for certain applications and a demerit for others. Therefore, the desired fresh and mechanical properties (e.g., workability, setting time, compressive strength, etc.) can be controlled for a given geopolymer source material through its partial substitution by natural or by-product materials. Recognizing the critical role of various replacement materials in enhancing the potential applications of geopolymer composites, the present review was undertaken to quantify and understand the effect of partial replacement by fly ash, metakaolin, kaolin, red mud, slag, ordinary Portland cement, and silica fume on the setting time, workability, compressive strength and flexural strength of various source materials addressed in the literature. The review also provides insights into research gaps in the field to promote future research.     

Design and experimental investigation of the high efficiency 1.5 W/4.2 K pneumatic-drive G-M cryocooler

The development of a high cooling power and high efficiency 4.2 K two stage G-M cryocooler is critically important given its broad applications in low temperature superconductors, MRI, infrared detector and cryogenic electronics. A high efficiency 1.5 W/4.2 K pneumatic-drive G-M cryocooler has recently been designed and developed by ARS. The effect of expansion volume rate and operation conditions on the cooling performance has been experimentally investigated. A typical cooling performance of 1.5 W/4.2 K has been achieved, and the minimum temperature of the second stage is 2.46 K. The steady input power of the compressor at 60 Hz is 6.8 kW, while the operation speed of the rotary valve is 30 rpm. A maximum cooling power of 1.75 W/4.2 K has been obtained in test runs.     

The PAR(p) Interconfigurations model used by the Brazilian Electric Sector

This study discusses the characteristics of the Periodic Autoregressive model, PAR(p), which is used to generate synthetic series of inflow energies that serve as entries for computer platforms that implement the planning and expansion of the operations of the BES – the Brazilian Electric Sector (SEB – Sistema Elétrico Brasileiro). The methodology for the design of a generating plant is presented in addition to the fundamentals of the “PAR(p) Interconfigurations” Model, which is referred to as the Inflow Energy Generation Model (IEGM) in this study. The major contribution of this study is to provide the first scientific discussion of the representation of multiple configurations using the PAR(p) model. For this purpose, several topics related to the time series are discussed, such as the definition of the model order, the matter of stationarity and the need to address possible outliers. Finally, a case study is presented, wherein the results of the estimation and generation of the described model’s scenarios are demonstrated.     

Corrosion resistance of Al–Cr-slag containing chromium–corundum refractories to slags with different basicity

Al–Cr slag is the solid waste generated by the smelting of Cr metal. It presents a range of environmental hazards. This study addressed the corrosion resistance of Al–Cr slag containing chromium–corundum refractories to slags with different basicity. Herein, we provide suggestions for the use of Cr–corundum of different basicity in kilns. Al–Cr slag, brown fused Al₂O₃, and chrome green were used as the raw materials, with pure calcium aluminate cement being used as a binder. The brick samples, prepared using different blends of chrome green and corundum, were fired at 1600?°C, and subsequently subjected to a slag corrosion test. After corrosion by slag of different basicity, the phase composition and microstructure of the sample were analyzed by X-ray diffraction, energy dispersive spectrometer and scanning electron microscopy. There were two major findings. First, Cr–corundum brick made from Al–Cr slag has a better slag corrosion resistance than that made from Cr₂O₃ and brown fused Al₂O₃. Second, Cr–corundum brick made from Al–Cr slag has superior corrosion resistance to slag with a CaO:SiO₂ ratio of 2:1.     

提高托盘利用效率的重要手段——电子信息化管理

托盘能否有效运用对物流的畅通与否关系重大,这已经引起了国内外专家和学者们的重视,并就此制定了托盘电子信息化管理系统,旨在更合理地使用托盘,推进托盘一体化和共用系统的建立。而RFID技术在托盘的电子信息化管理的应用更将大大提高物流的效率与准确性,托盘电子信息化管理将成为今后托盘管理的趋势。     

实验室质量体系的建立与运行

详细论述了质量和质量体系的基本概念、建立质量体系的必要性、质量体系的构成和建立过程、质量体系文件的编制、质量体系的运行和持续改进以及中国实验室国家认可委员会的有关政策。     

空分设备系统操作中的物料平衡

本文以济南鲍德气体有限公司 2 0 0 0 0m3 /h空分设备为例 ,从物料平衡的观点出发 ,阐述了操作中一些应注意的问题及解决的措施。     

上半年石油工业经营情况及下半年走势预测

今年上半年我国石油工业基本保持平稳、健康的发展格局:油气产量和消费需求均持续增长,油气开采业大幅盈利,原油加工业仍然亏损,投资大幅度增长,原油进口依存度加大。下半年需要采取的应对措施是:进一步完善成品油价格形成机制;规范和引导上海石油交易所健康运行;加强天然气管理,作好需求预测;实施石油替代激励政策。预计下半年国际油价继续走高的可能性较大;我国全年石油表观消费可能会突破3亿吨,进口依存度继续在40%以上。