Internet网的服务方式与入网方式一览

目前，世界上最大的计算机网络Ｉｎｔｅｒｎｅｔ网，已成为通达１５０多个国家的国际互联网络。作为引导中国计算机用户进入Ｉｎｔｅｒｎｅｔ的中国公用计算机互联网ＣＨＩＮＡＮＥＴ也正迅速发展。本文就Ｉｎｔｅｒｎｅｔ网的服务方式和入网方式进行了综述。     

Characteristics of hydrostatic bearing/seal parts for water hydraulic pumps and motors. Part 1: Experiment and theory

In this paper, the load-carrying capacity, power losses and stiffness of disk-type hydrostatic thrust bearings including the case of eccentric loading are discussed theoretically. The numerical analysis method is established based on a two-dimensional elastohydrostatic problem with an elastic deformation model, which is extended to adapt it for a non-axisymmetric load acting on the thrust bearing. The bearing is made of a combination of stainless steel/stainless steel and stainless steel/plastics. For the elastic materials, the maximum stiffness derived from, i.e., minimum film thickness is, larger than that of the rigid material in the range of a large ratio of pocket pressure and a hydrostatic balance ratio of over unity, which is defined as the ratio of the load to the maximum hydrostatic load-carrying capacity. The maximum load-carrying capacity and minimum power loss can exist in the domain of the hydrostatic balance ratio over unity for the case of the bearing consisting of elastic/rigid materials, in comparison with that composed of the same rigid materials. For the case of water, the power loss due to leakage flow is slightly larger but that due to frictional torque is much smaller than that in the case of hydraulic oil. Then, the total power loss is much smaller than that of hydraulic oil.     

连铸喷嘴特性测试与分析

通过测试连铸二冷喷嘴性能，对比同型号喷嘴使用前后两种状态下特性参数，分析了喷嘴参数变化的原因。提出了对使用中的喷嘴特性进行检测与校核的建议，以确保喷嘴特性满足铸坯二冷工艺条件，保证铸坯质量。     

固体火箭发动机喷管用烧蚀隔热材料研究进展

介绍了固体火箭发动机喷管用烧蚀隔热材料的研究进展，喷管受热分析，指出了先进复合材料的发展趋势，提出碳／酚醛复合材料在制造低成本的发动机喷管中仍有重大使用价值。     

Effect of spray nozzle design on liquid-solid contact in fluidized beds

In industrial fluid cokers the feedstock, consisting of heavy bituminous hydrocarbons, is atomized with steam and injected into a hot fluidized bed of coke. Good and uniform contact of the liquid droplets with the solid particles is required to provide heat for the cracking reactions while minimizing mass transfer effects. Experiments in a pilot plant coker have suggested that the initial particle/liquid mixing, in the spray jet, is rather poor. Experiments in a X-ray scanner showed that liquid droplets and entrained particles accumulate just below the tip of the jet plume to form agglomerates.An experimental technique was used to quantitatively determine the quality of mixing with a variety of nozzle configurations including several novel designs. By improving spray stability, redistributing liquid droplets to the solids-rich region of the jet and increasing the surface area of the gas-liquid jet-fluidized bed interface, liquid/solid contact is improved.     

An efficient IP address lookup algorithm based on a small balanced tree using entry reduction

Due to a tremendous increase in internet traffic, backbone routers must have the capability to forward massive incoming packets at several gigabits per second. IP address lookup is one of the most challenging tasks for high-speed packet forwarding. Some high-end routers have been implemented with hardware parallelism using ternary content addressable memory (TCAM). However, TCAM is much more expensive in terms of circuit complexity as well as power consumption. Therefore, efficient algorithmic solutions are essentially required to be implemented using network processors as low cost solutions.Among the state-of-the-art algorithms for IP address lookup, a binary search based on a balanced tree is effective in providing a low-cost solution. In order to construct a balanced search tree, the prefixes with the nesting relationship should be converted into completely disjointed prefixes. A leaf-pushing technique is very useful to eliminate the nesting relationship among prefixes [V. Srinivasan, G. Varghese, Fast address lookups using controlled prefix expansion, ACM Transactions on Computer Systems 17 (1) (1999) 1-40]. However, it creates duplicate prefixes, thus expanding the search tree.This paper proposes an efficient IP address lookup algorithm based on a small balanced tree using entry reduction. The leaf-pushing technique is used for creating the completely disjointed entries. In the leaf-pushed prefixes, there are numerous pairs of adjacent prefixes with similarities in prefix strings and output ports. The number of entries can be significantly reduced by the use of a new entry reduction method which merges pairs with these similar prefixes. After sorting the reduced disjointed entries, a small balanced tree is constructed with a very small node size. Based on this small balanced tree, a native binary search can be effectively used in address lookup issue. In addition, we propose a new multi-way search algorithm to improve a binary search for IPv4 address lookup. As a result, the proposed algorithms offer excellent lookup performance along with reduced memory requirements. Besides, these provide good scalability for large amounts of routing data and for the address migration toward IPv6. Using both various IPv4 and IPv6 routing data, the performance evaluation results demonstrate that the proposed algorithms have better performance in terms of lookup speed, memory requirement and scalability for the growth of entries and IPv6, as compared with other algorithms based on a binary search.     

EFFECT OF CROSS FLOW ON THE SPRAY CHARACTERISTICS OF AN INDUSTRIAL FEED NOZZLE

The spray characteristics of a scaled-down version of an industrial feed nozzle are studied in the presence of a cross flow. Aerated liquid nitrogen is injected through the nozzle to generate the spray. The aeration rate is low and held constant, while two different liquid flow rates are used to produce the spray. A nonuniform wind profile is chosen to represent the cross flow condition. The droplet diameter and velocity measurements are acquired using a phase-Doppler particle analyzer. The results of the present study indicate that the spray momentum flux determines the extent of the jet bending. The droplets are accelerated significantly in the initial jet region as a result of flashing. However, further downstream of the nozzle, the vaporization of the droplets is considered to be negligible. The size-velocity correlation changes significantly for the case where the spray is shifted due to the cross flow.     

提高锅炉雾化喷嘴的雾化效果的几种手段

雾化喷嘴是各行各业中都非常关键的设备,其雾化效果在工农业中都非常重要,雾化的手段和方法更是多种多样,而提高雾化效果对于节能、环保等都非常关键,本文将着重介绍提高喷嘴雾化效果的几种方法。     

Analysis of surface integrity for minimum quantity lubricant—MQL in grinding

The quality of machined components is currently of high interest, for the market demands mechanical components of increasingly high performance, not only from the standpoint of functionality but also from that of safety. Components produced through operations involving the removal of material display surface irregularities resulting not only from the action of the tool itself, but also from other factors that contribute to their superficial texture. This texture can exert a decisive influence on the application and performance of the machined component. This article analyzes the behavior of the minimum quantity lubricant (MQL) technique and compares it with the conventional cooling method. To this end, an optimized fluid application method was devised using a specially designed nozzle, by the authors, through which a minimum amount of oil is sprayed in a compressed air flow, thus meeting environmental requirements. This paper, therefore, explores and discusses the concept of the MQL in the grinding process. The performance of the MQL technique in the grinding process was evaluated based on an analysis of the surface integrity (roughness, residual stress, microstructure and microhardness). The results presented here are expected to lead to technological and ecological gains in the grinding process using MQL.     

基于随机开关喷孔数量的3D错位打印研究及应用

3D打印机打印过程是逐层堆砌打印,在实际的工业生产中,打印机喷头经常会出现部分喷孔堵塞,无法喷墨的情况,导致打印的零部件在层叠加方向上堵塞喷孔的部位始终无法喷洒粘接剂造成断裂面而成型失败。目前只能清理喷孔后再重新打印或更换喷头解决上述问题,但是会造成喷头使用寿命减短、生产效率降低、成本增加等问题。通过随机开关部分喷孔和打印头偏移相结合的方式可以有效的避免因少量喷孔堵塞而导致的打印零部件断裂报废的问题,也可延长喷头使用寿命。从而使得3D打印在生产制造领域使用的更加得心应手。