Viscosity estimation for slags containing calcium fluoride

Based on recently published experimental data, the Riboud model was modified for viscosity estimation of the slags containing calcium fluoride. The estimated values were in good agreement with measured data. Reasonable estimation can be achieved using the modified Riboud model for mould fluxes and ESR (eletro slag remelting) slags. Especially for ESR slags, the modified Riboud model can provide much more precise values than the original Riboud model.     

大截面金属镍棒的焊接工艺与实践

金属镍在电渣精炼前需用氩弧焊焊接接长,为保证焊接接头具有足够熔深,需要大参数进行焊接.采用直流焊机并联使用解决了焊机电流不足的情况,通过采取垫高镍棒端头,使接缝处于受压状态,以防止裂纹的产生.     

ESR Refining Potential for Titanium Alloys using a CaF2‐based Active Slag

Since the end of the Cold War and due to the needs to produce titanium more cost‐efficient and thus more attractive for its civilian use, the electroslag remelting (ESR) process has become an increasingly important topic of international research programmes, because titanium and titanium aluminides can be chemically refined by ESR in some degree. Using ESR, titanium turnings from machining steps and scrap from foundries can be remelted, refined and provided as secondary titanium for the market at relatively favourable prices. This article investigates the removability of the main impurities out of titanium and titanium‐aluminium alloys by electroslag remelting using the active slag system CaF₂‐Ca‐(CaO). Thermochemical and kinetic aspects of the ESR process are considered.     

Study on Factors Affecting the Structure of High SpeedSteel Ingot Produced by ESR

ＳｔｕｄｙｏｎＦａｃｔｏｒｓＡｆｆｅｃｔｉｎｇｔｈｅＳｔｒｕｃｔｕｒｅｏｆＨｉｇｈＳｐｅｅｄＳｔｅｅｌＩｎｇｏｔＰｒｏｄｕｃｅｄｂｙＥＳＲＬｉＺｈｅｎｇｂａｎｇ；ＣｈｅＸｉａｎｇｑｉａｎＡｂｓｔｒａｃｔ：Ｔｈｅｉｎｆｌｕｅｎｃｅｏｆｔｈｅｍｅｔａｌｐ...     

Mg-Li-Al合金近液相线制浆及部分重熔

采用近液相线铸造方法制备了Mg—5％Li—3％A1合金的半固态浆料。通过对该合金近液相线铸造与常规铸造组织进行比较，以及在不同静置时间、不同冷却速率下对其铸造组织的影响，较详细地分析了近液相线铸造组织的变化过程。试验结果表明，在Mg—Li合金熔炼中，添加2％Ca可实现阻燃，但效果不如对一般镁合金；与常规铸造相比，近液相线铸造可获得均匀、细小枝晶的组织结构；适当静置或提高冷却速率有利于组织的细化和均匀化；在适当的部分重熔工艺条件下，坯料组织可获得较理想的触变组织。     

Ti-23Al-14Nb-3V合金氩弧焊接头的显微组织及其力学性能

研究了预热对Ｔｉ－２３Ａｌ－１４Ｎｂ－３Ｖ合金焊接性，特别是对消除氩弧焊冷裂纹的作用以及对接头显微组织和力学性能的影响。结果表明，焊前预热可有效降低该合金的冷裂倾向。经预热处理后，焊缝区的结晶层状线消失，热影响区的硬度峰得到缓和，整个焊缝的显微硬度分布趋于均匀，但焊缝区的枝晶发生粗化，热影响区有所扩大。焊件接头的拉伸试验表明，预热可使焊缝区的接头强度系数增加，但无论预热与否，接头强度均低于母材强度，且不显示宏观塑性。     

电渣20Mn1A钢中铝和钛的控制

总结了电渣 2 0Mn1A钢从电炉冶炼到电渣重熔钢中铝、钛及主要成分的变化情况 ,为该钢的生产提供了控制成分的依据     

一种小电流下的引弧及稳弧方法

介绍一种小电流直流TIG焊中的引弧及稳弧方法，并对实现此功能的控制电路进行了详细的分析。简单介绍了此种小型焊机的特点及用途。     

Processing of yttria partially stabilized zirconia thermal barrier coatings implementing a high-power laser diode

Several studies have been undertaken recently to adapt yttria partially stabilized zirconia (YPSZ) thermal barrier coating (TBC) characteristics during their manufacturing process. Thermal spraying implementing laser irradiation appears to be a possibility for modifying the coating morphology. This study aims to present the results of in situ (i.e., simultaneous treatment) and a posteriori (i.e., post-treatment) laser treatments implementing a high-power laser diode. In both cases, the coatings underwent atmospheric plasma spraying (APS). Laser irradiation was achieved using a 3 kW, average-power laser diode exhibiting an 848 nm wavelength. Experiments were performed to reach two goals. First, laser post-treatments aimed at building a map of the laser-processing parameter effects on the coating microstructure to estimate the laser-processing parameters, which seem to be suited to the change into in situ coating remelting. Second, in situ coating remelting aimed at quantifying the involved phenomena. In that case, the coating was treated layer by layer as it was manufactured. The input energy effect was studied by varying the scanning velocity (i.e., between 35 and 60 m/min), and consequently the irradiation time (i.e., between 1.8 and 3.1 ms, respectively). Experiments showed that coating thermal conductivity was lowered by more than 20% and that coating resistance to isothermal shocks was increased very significantly.