"毛虫"建筑--一次装配建筑的实验

文章详细介绍了瑞士霍夫·威施巴德餐厅因苛刻的条件而采用的特殊的设计建造的方法和过程——在基地外的一次预制装配的预演实验,同时也分析了该项目在设计上由于考虑适合装配生产特点而形成的空间效果。     

A Method to Measure Emissions from Dryers with Diffuse Leakages, Using Evaporated Water as a Tracer

This paper describes a novel method to measure emission from dryers. The method resolves the known difficulties caused by diffuse emissions, and also solves the problems associated with high moisture content of the drying medium. The basic idea is to use water vapor to determine the exhaust flow, while a dry ice trap is used both to preconcentrate emitted VOCs and to determine the moisture content of the drying medium.     

Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

野外大气扩散试验中四面体气球示踪实验的初步评价

1985年11月在瑞士北部进行了一次以探讨“冷池”条件下的扩散和湍流特征为目的的国际野外大气试验,本文介绍其中的四面体气球示踪实验的结果。一共进行了三次由雷达跟踪的四面体示踪实验,释放了10个四面体球。按多轨迹法和单轨迹法分别估算并比较了其中两次示踪实验得到的水平扩散参数σ_y,探讨了风摆效应的贡献。采用“体源模式”并结合单轨迹法估算了微弱风场不定风向条件下的扩散参数,分析了静风,弱风条件下的水平风向标准差和湍流强度。     

数控超声加工的初步工艺试验

介绍在经过数控化改造的两坐标超声加工机床上所进行数控超声加工的初步工艺试验,并讨论试验结果。     

The Design of Discrimination Experiments

Experimentation plays a fundamental role in scientific discovery. Scientists experiment to gather data, investigate phenomena, measure quantities, and test theories. In this article, we address the problem of designing experiments to discriminate between two completing theories. Given an initial situation for which the two theories make the same prediction, the experiment design problem is to determine how to modify the situation such that the two theories make different predictions for the modified situation. The modified situation is called a discrimination experiment. We present a knowledge-intensive method called DEED for designing discrimination experiments. The method analyzes the differences in the two theories' explanations of the prediction for the initial situation. Based on this analysis, it determines modifications to the initial situation that will result in a discrimination experiment. We illustrate the method with the design of experiments to discriminate between several pairs of qualitative theories in the fluids domain.     

屏蔽暂堵反排解堵效率的实验分析

在一定实验条件下，屏蔽暂堵的反排解堵效率随压差、温度的增大而增大，反排解堵在很短的时间内就可完成。一般的反排解堵率都在60％以上，但反徘不能完全解堵。     

包气带中不同示踪源层条件下核素迁移对比试验

为研究不同示踪源层材料对水份运移和核素迁移的影响，开展了以石英砂和黄土分别为示踪源层载体时Sr、Nd、Ce在包气带中迁移的对比试验。试验历时470d，在两种源层条件下各取土芯样4次。试验结果表明：在喷淋强度为5mm/h、3h/d条件下，Nd和Ce无论在石英砂示踪源层还是黄土示踪源层中浓度峰位均没有明显向下迁移；对于Sr，在黄土示踪源层中，470d后其峰位向下迁移约15cm(按质心计算为10cm左右)，而从石英砂示踪源层中向下迁移不明显（按质心计算，迁移约2.7cm），只是峰位有些展宽。上述结果表明，极薄（7mm）的细石英砂层也能对非饱和入渗水产生明显屏流作用，使得核素从石英砂示踪源层中向下迁移速度减慢。     

利用先进的结构试验系统进行发动机构件的仿真疲劳试验

本文介绍一套先进的构件实验设备的功能及其在发动机构件疲劳试验方面的具体应用实例．通过对几种受力较复杂构件的受力分析设计出实验方法，使构件在实验室中受力情况与构件实际受力情况相似或相同，这样，得出的试验数据就可为构件的可靠性分析工作提供较好的依据．     

Determining stress intensity factors of composites using crack opening displacement

The main purpose of this paper is to find the mixed-mode stress intensity factors of composite materials using the crack opening displacement (COD). First, a series solution of the composite material with a crack was used to evaluate COD values. Then, the least-squares method was used to calculate mixed-mode stress intensity factors. This algorithm can be applied to any method that generates or measures COD values. The major advantage of this method is that COD values very near the crack tip are not necessary. Both finite element simulations and laboratory experiments were applied to validate this least-squares method with acceptable accuracy if the even terms of the series solution are removed.