全文获取类型
收费全文 | 155篇 |
免费 | 8篇 |
国内免费 | 2篇 |
专业分类
电工技术 | 1篇 |
综合类 | 6篇 |
化学工业 | 43篇 |
金属工艺 | 25篇 |
能源动力 | 3篇 |
冶金工业 | 87篇 |
出版年
2022年 | 4篇 |
2019年 | 2篇 |
2018年 | 1篇 |
2017年 | 6篇 |
2016年 | 6篇 |
2015年 | 2篇 |
2014年 | 2篇 |
2013年 | 13篇 |
2012年 | 7篇 |
2011年 | 15篇 |
2010年 | 5篇 |
2009年 | 12篇 |
2008年 | 5篇 |
2007年 | 11篇 |
2006年 | 12篇 |
2005年 | 8篇 |
2004年 | 5篇 |
2003年 | 6篇 |
2002年 | 7篇 |
2001年 | 10篇 |
2000年 | 5篇 |
1999年 | 4篇 |
1998年 | 2篇 |
1997年 | 5篇 |
1996年 | 1篇 |
1995年 | 3篇 |
1994年 | 2篇 |
1993年 | 4篇 |
排序方式: 共有165条查询结果,搜索用时 15 毫秒
1.
阐述了中间罐车的设计要求及选型,较详细地分析了行走、升降机构的结构及设计。根据行走机构的特点,提出了2K-H型双速行星减速器的设计方法。 相似文献
2.
3.
4.
矾土尖晶石钢包浇注料的研制与应用 总被引:2,自引:0,他引:2
采用特级矾土熟料为骨科,天然出合成的镁铝尖晶石为部分基质,选用新型复合结合剂研制成矾土尖晶石质钢包浇注料.使用结果表明:一次性寿命较传统的铝镁浇注料提高80%以上. 相似文献
5.
6.
利用数模研究了钢水在常密度和密度变化两种条件时,中间包内的流场、温度场和钢水平均停留时间.计算结果说明高温钢水在中间包内流动时,不能忽略自然对流流动,密度随温度变化时,钢水沿着液面流到水口区,没有短路流现象,最短滞流时间150s,进出口温差46℃,其流场和温度场与常密度条件下的正好相反. 相似文献
7.
板坯连铸中间包钢液洁净度的水力学模拟和应用 总被引:4,自引:1,他引:4
为改善太钢 10 4 0mm× 16 0mm连铸不锈钢板坯质量 ,通过水力学模拟研究了中间包内钢液的流动 ,并用直径 0 .5~ 1.0mm ,密度 0 .99mg/mm3 的聚苯乙烯塑料粒子模拟钢中直径 5 0~ 10 0 μm夹杂物的排除情况 ,确定了在中间包内设置挡渣墙和坝流控制方案 ,并进行 4 0 9不锈钢 10 4 0mm× 16 0mm连铸板的工业试验 ,结果表明 :中间包设置挡渣墙和坝后 ,铸坯夹杂物总量比中间包无控流装置生产的铸坯降低 6 6 %。 相似文献
8.
《钢铁冶炼》2013,40(6):453-463
AbstractSingle phase (liquid steel) and two-phase (liquid steel and argon bubbles) three-dimensional computational fluid dynamic and heat transfer models were developed for the continuous casting machines of ArcelorMittal. The computational domains include tundishes, slide gates, submerged entry nozzles and moulds. The effects of buoyancy, tundish design, tundish practices, nozzle design and caster practices on flow structure were investigated. Mathematical modelling is discussed in detail. In addition, submeniscus velocity measurements in the slab caster mould are performed with the method of torque measurement. A consumable probe is inserted into the liquid steel meniscus from the top of the mould through mould powder and slag layer. The liquid steel flow applies a drag force to the probe, which then generates a torque. This torque value is measured and then converted back to velocity. The concept and challenges of the technique are discussed, and the effects of casting parameters on mould flow structure are investigated. Product quality in relation to real time meniscus velocity measurements is also discussed. 相似文献
9.
采用物理模拟的方法,对离心中间包净化钢液的动力学进行了考察。采用低熔点金属液,分别考察金属液柱高度、锥度、磁感应强度、电阻率、磁场分布、屏蔽等对金属液旋转运动的影响。结果表明,增加磁感应强度、提高金属液柱深度、适当增加金属液旋转腔的锥度将有助于获得更高的金属液转速;金属液旋转速度与金属液的电阻率成反比关系。当磁感应强度为14.4mT时,钢液的转速预计可达80r/min;采用活塞流模型计算的夹杂物去除效果表明,100r/min的钢液转速和钢液1t/min的流量下,直径20um以上的夹杂物去除效率可以达到70%以上. 相似文献
10.