Synthesis and wear of Al based,free standing functionally gradient materials: effects of different reinforcements

Abstract

In the present study, three aluminium based functionally gradient materials (FGMs), reinforced with different ceramic particulates (silicon carbide, aluminium oxide, and titanium carbide), were successfully synthesised using the innovative gradient slurry disintegration and deposition (GSDD) technique. The results for Al/SiC and Al/Al₂O₃ revealed, in common, an increase in the weight percentage of reinforcement along the direction of deposition, to result in an increase in porosity and microhardness. However, for Al/TiC, the reverse trend was observed, with porosity and microhardness decreasing with increasing distance from the base of the ingot. The porosity levels for Al/TiC were also found to be significantly lower than those ofthe other two FGMs. Thermomechanical analysis of the FGMs showed thatthe average coefficient of thermal expansion of the high reinforcement end was reduced, as compared to the high aluminium end. Sliding wear test results also revealed that the high reinforcement end was more wear resistant than the high aluminium end, except for the case of Al/Al₂O₃. An attempt is made to interrelate the effects of different types of particulates, with microstructural development, microhardness and wear rate results obtained in the present study.     

Microstructural evolution of Inconel* 718 during ingot breakdown: process modelling and validation

Abstract

A computer model is presented that describes microstructural evolution during the ingot breakdown of nickel base superalloy Inconel 718 via the open die cogging operation. To support the development of the model, a compression testing programme has been carried out which covers the ranges of temperatures, strains, and strain rates experienced during thermomechanical processing. Analysis of the flow curves has allowed the identification of the regimes in which the various deformation mechanisms take place. Logic based rules have been incorporated into the model, and this has allowed predictions of the microstructural evolution to be made. Where possible, the results have been compared with the available experimental data and it is shown that theory and experiment are in reasonable agreement. A number of computational experiments have been carried out, to study the effects of changing the forging procedure.     

Utilisation of silicon rubber to characterise tool surface quality during die compaction

Abstract

A new methodology was developed to observe and measure tool wear and tool surface quality during the die compaction process. The newly developed method is a non-destructive test that relies on silicon rubber to transcribe the inner surface profile of the compaction die. After verification of the method, aluminium and iron alloy powders were compacted to quantify tool wear and tool surface quality with two die materials, tungsten carbide and tool steel. The tool surface quality was quantified by recording surface roughness of the die replicas on a surface profilometer.     

Pack formation and long term oxidation kinetics of TiAl3 coating on γ-TiAl

Abstract

The aim of this study is to produce microcracking free TiAl₃ coatings on γ-TiAl alloy by the pack cementation process and to determine the long-term oxidation kinetics and thermal stability of the coating at high temperatures. It was shown that microcracking free coatings could be prepared in the AlCl₃ activated packs containing 4 wt-%Al as the depositing source. The conditions required for the formation of a microcracking free coating are discussed in relation to the pack chemistry at high temperatures. The TiAl₃ coatings formed were oxidised in air for more than 6200 h, during which weight gains were measured at regular intervals. The major oxide in the scale was Al₂O₃. It was observed that a TiAl₂ phase zone formed in the subsurface of the scale as a result of preferential oxidation of Al in the TiAl₃ coating. It was found that a linear relationship existed between the weight gain and logarithm of time of oxidation at 800°C: Δm _t = k _lln(αt+ 1). The thermal stability of the coating was assessed by measuring the growth kinetics of the TiAl₂ interlayer at the boundary between the TiAl₃ coating and substrate, which was determined to be d^1·4 = 0·1t (d and t in μm and h respectively) at 800°C using the experimental data measured over a diffusion annealing period of more than 6200 h.     

Direct observation of ternary solid state transformation in Bi–Cd–In alloy system

Abstract

Cast or solution treated specimens of a Bi–9·0Cd–26·7In (wt-%) alloy were observed to form a fine, three phase microstructure on aging at room temperature, replacing a single phase formed at a higher temperature. The three phases resulting from this solid state reaction were found to grow with a lamellar morphology into the high temperature phase, with a growth rate of 0·5–1·0 μm h^-1 at room temperature. The equilibrium temperature for the transformation was found to be ～25°C. Using a Hitachi S-4500 field emission SEM, the phase transformation was followed in progress at magnifications of 3000 and 10 000 times. It was noted that a volume change was associated with the transformation. It was concluded that the transformation is of the ternary eutectoid type.     

Comparative study of three different types of dental diamond burs

Abstract

Wear mechanisms of three different types of dental burs were studied by means of cutting experiments performed on machinable glass ceramic using a laboratory system designed for this purpose. The dental handpiece used for this research was subjected to a constant feed rate in order to better simulate the actual working conditions of a dental bur. The new and the worn-out burs were studied by optical and scanning electron microscopy. Diamond particle wear-out was found to be the dominant wear mechanism in all cases; a quantitative analysis was performed on the optical micrographs of the new and worn burs. In situ force measurements showed that the forces exerted by the bur increase with the blunting process in order to keep the required feed rates; each bur type seems to have a different characteristic curve of force versus the number of cuts.     

Reverse transformation mechanism of martensite to austenite and amount of retained austenite after reverse transformation in Fe-3Si-13Cr-7Ni (wt-%) martensitic stainless steel

Abstract

The reverse transformation mechanism of martensite to austenite and the volume fraction of retained austenite have been studied in an Fe-3Si-13Cr-7Ni (wt-%) martensitic stainless steel by means of dilatometry, transmission electron microscopy and X-ray diffraction. Below a heating rate of 10 K s^-1, the reverse transformation of α' to γ occurs by diffusion, whereas it occurs by a diffusionless shear mechanism above 10 K s^-1. After reversion treatment at low temperatures, filmlike retained austenite is observed along α' lath boundaries, while reversion treatment at high temperatures produces granular retained austenite inside the α' laths in addition to filmlike retained austenite. The volume fraction of retained austenite at room temperature increases with increasing reversion treatment temperature, exhibiting a maximum at ~625^° C, above which it decreases with increasing reversion temperature.     

Effects of different metals on adhesive wear behaviour of alloy surface produced by TIG process

Abstract

Low carbon steel surfaces were alloyed with composite powders using the tungsten inert gas welding method. After the alloying process, the effects of cladding surface on the microstructural characteristics and adhesive wear of the alloyed samples were examined. The sliding wear behavior of samples was investigated in a block on ring apparatus under the loads of 20, 40, 60 and 80 N respectively. In the experimental investigation, a low carbon steel surface was alloyed with austenitic stainless steel powder and austenitic stainless steel powder mixed with 4·5% Co, Mo and Ti particles respectively. Following surface alloying, conventional characterisation techniques, such as optical microscopy, scanning electron microscopy, energy dispersive spectrograph and X-ray diffraction, were used to study the microstructure of the alloyed zone. Examination of the microstructure revealed the presence of M₂₃C₆ carbides, solid melt phases and intermetallic phases, such as Ni₃Ti, depending on the alloying element in the composite. As the amount of the reinforcing material increased, the saturation rates for the samples decreased, while their hardness increased. The adhesive abrasion tests conducted revealed that temperature input plays a significant role on the microstructure characteristics, which positively affected the adhesive abrasion values of the samples. Consequently, the tungsten inert gas welding method was successfully used for the surface alloying of low carbon steels.     

Periodic reverse current electrodeposited nickel pigmented anodised aluminium

Abstract

Aluminium anodically oxidised in sulphuric acid electrolyte was pigmented by an electrolytic colouring process with the use of alternating and periodic reverse current. The applied pigmentation electrolytes were based on nickel. The study reports on resistance against humidity of a selective Ni–Al₂O₃ layer. The samples before and after testing were analysed and compared. The quality of the coating, optical properties and influence of humidity on morphology and composition of the coatings were investigated. The influence of moisture on the quality of the selective Ni–Al₂O₃ layer is comparable to the commercial solar absorber type.