Novel TiC-based composites with enhanced mechanical properties

Novel TiC-based composites were synthesized by reactive hot-pressing at 1800 °C for 1 h with ZrB₂ addition as a sintering aid for the first time. The effects of ZrB₂ contents on the phase composition, microstructure evolution, and mechanical properties were reported. Based on the reaction and solid solution coupling effects between ZrB₂ and TiC, the product ZrC may be partially or completely dissolved into the TiC matrix, and then phase separation within the miscibility gap is observed to form lamellar nanostructured ZrC-rich (Zr, Ti)C. The TiC-10 mol.% ZrB₂ (starting batch composition) exhibits good comprehensive mechanical properties of hardness 27.7 ± 1.3 GPa, flexural strength 659 ± 48 MPa, and fracture toughness of 6.5 ± 0.6 MPa m^1/2, respectively, which reach or exceed most TiC-based composites using ceramics as sintering aids in the previous reports.     

Fabrication and laser performances of Yb:Sc2O3 transparent ceramics from different combination of vacuum sintering and hot isostatic pressing conditions

In this paper we report on the preparation and laser performance of transparent 3at.% Yb:Sc₂O₃ ceramics by reactive sintering of commercially available powders under vacuum followed by hot isostatic pressing (HIP). Combinations of different vacuum sintering temperatures (1650 °C and 1750 °C) and different HIP treatments (1700 °C and 1800 °C at 200 MPa) were tested in order to understand how these steps influence the microstructure and thus the optical and lasing properties of the ceramic samples. All the samples showed a good optical quality. The microstructure analysis and the laser tests showed that the vacuum pre-sintering temperature is the key factor determining the quality of the samples and the laser performances. The best values of slope efficiency i.e. η_L = 50 % and output power i.e. P_out = 6.62 W were obtained for the sample pre-sintered under vacuum at 1650 °C and hot isostatically pressed at 1800 °C.     

Rectangular Section Control Technology for Silicon Steel Rolling

Rectangular section control technology(RSCT)was introduced to achieve high-precision profile control during silicon steel rolling.The RSCT principle and method were designed,and the whole RSCT control strategy was developed.Specifically,RSCT included roll contour design,rolling technology optimization,and control strategy development,aiming at both hot strip mills(HSMs)and cold strip mills(CSMs).Firstly,through the high-performance variable crown(HVC)work roll optimization design in the upper-stream stands and the limited shifting technology for schedule-free rolling in the downstream stands of HSMs,a hot strip with a stable crown and limited wedge,local spot,and single wave was obtained,which was suitable for cold rolling.Secondly,an approximately rectangular section was obtained by edge varying contact(EVC)work roll contour design,edge-drop setting control,and closed loop control in the upper-stream stands of CSMs.Moreover,complex-mode flatness control was realized by coordinating multiple shape-control methods in the downstream stands of CSMs.In addition,the RSCT approach was applied in several silicon-steel production plants,where an outstanding performance and remarkable economic benefits were observed.     

Microstructure and mechanical properties of hot-pressed SiC nanofiber reinforced SiC composites

This study reports on the preparation and mechanical properties of a novel SiC_nf/SiC composite. The single crystal SiC nanofiber(SiC_nf) reinforced SiC ceramic matrix composites (CMC) were successfully fabricated by hot pressing the mixture of β-SiC powders, SiC_nf and Al–B–C powder. The effects of SiC_nf mass fraction as well as the hot-pressing temperature on the microstructure and mechanical properties of SiC_nf/SiC CMC were systematically investigated. The results demonstrated that the 15 wt% SiC_nf/SiC CMC obtained by hot pressing (HP) at 1850 °C with 30 MPa for 60 min possessed the maximum flexural strength and fracture toughness of 678.2 MPa and 8.33 MPa m^1/2, respectively. The nanofibers pull out, nanofibers bridging and cracks deflection were found by scanning electron microscopy, which are believed can strengthen and toughen the SiC_nf/SiC CMC via consuming plenty of the fracture energy. Besides, although the relative density of the prepared SiC_nf/SiC CMC further increased with the sintering temperature rose to 1900 °C, the further coarsend composites grains results in the deterioration of the mechanical properties for the obtained composites compared to 1850 °C.     

Characterizing physical habitat preferences and thermal refuge occupancy of brook trout (Salvelinus fontinalis) and Atlantic salmon (Salmo salar) at high river temperatures

Anthropogenic influences, including climate change, are increasing river temperatures in northern and temperate regions and threatening the thermal habitats of native salmonids. When river temperatures exceed the tolerance levels of brook trout and Atlantic salmon, individuals exhibit behavioural thermoregulation by seeking out cold‐water refugia – often created by tributaries and groundwater discharge. Thermal infrared (TIR) imagery was used to map cold‐water anomalies along a 53 km reach of the Cains River, New Brunswick. Trout and salmon parr did not use all identified thermal anomalies as refugia during higher river temperature periods (>21°C). Most small‐bodied trout (8–30 cm) were observed in 80% of the thermal anomalies sampled. Large‐bodied trout (>35 cm) required a more specific set of physical habitat conditions for suitable refugia, that is, 100% of observed large trout used 30% of the anomalies sampled and required water depths >65 cm within or adjacent to the anomaly. Densities of trout were significantly higher within anomalies compared with areas of ambient river temperature. Salmon parr were less aligned with thermal anomalies at the observed temperatures, that is, 59% were found in 65% of the sampled anomalies; and densities were not significantly different within/ outside anomalies. Salmon parr appeared to aggregate at 27°C, and after several events over 27°C variability in aggregation behaviour was observed – some fish aggregated at 25°C, others did not. We stipulate this is due to variances of thermal fatigue. Habitat suitability curves were developed for velocity, temperature, depth, substrate, and deep water availability to characterize conditions preferred by fish during high‐temperature events. These findings are useful for managers as our climate warms, and can potentially be used as a tool to help conserve and enhance thermal refugia for brook trout and Atlantic salmon in similar systems.     

Microstructures and mechanical properties of B4C-TiB2-SiC composites fabricated by ball milling and hot pressing

B₄C-TiB₂-SiC composites were fabricated via hot pressing using ball milled B₄C, TiB₂, and SiC powder mixtures as the starting materials. The impact of ball milling on the densification behaviors, mechanical properties, and microstructures of the ceramic composites were investigated. The results showed that the refinement of the powder mixtures and the removal of the oxide impurities played an important role in the improvement of densification and properties. Moreover, the formation of the liquid phases during the sintering was deemed beneficial for densification. The typical values of relative density, hardness, bending strength, and fracture toughness of the composites reached 99.20%, 32.84?GPa, 858?MPa and 8.21?MPa?m^1/2, respectively. Crack deflection, crack bridging, crack branching, and microcracking were considered to be the potential toughening mechanisms in the composites. Furthermore, numerous nano-sized intergranular/intragranular phases and twin structures were observed in the B₄C-TiB₂-SiC composite.     

燃气热水器在无回水管水路中实现零冷水的方案研究

本文分析了燃气热水器行业针对无回水管水路系统实现零冷水功能的现有技术方案,指出现有技术方案存在的一些缺陷,并结合试验研究,对无回水管水路系统提出了一套全新的实现零冷水功能的技术解决方案。     

LNG冷量优化集成利用技术

我国将相继在沿海地区建成多个LNG接收站，每年将进口数以千万吨计的LNG，同时携带数着巨额冷量，而这些冷量可用于发电、空气分离、制造干冰、低温冷库等众多领域。基于国外LNG冷量利用现状，指出我国即将展开和实施此项技术还存在着：过程火用损较大，缺乏系统、全面的LNG冷量利用技术的研发指导机制，以及宏观调控力度薄弱等问题，进而提出了发展LNG冷量的集成利用方案，可为此类技术的研发利用提供新思路。以福建即将进口的LNG为例，模拟了空气分离与干冰制备的集成工艺流程，结果表明：福建每年进口的260×10⁴t LNG可以冷却290×10⁴t空气，相当于60000 m³/h的氧气制备规模，还可以生产100×10⁴t的干冰，其过程火用损较小；其剩余的高温位冷量可应用于低温冻结库或冰灯等项目，这对主体装置的实施效果和过程火用损的影响较小。该技术的优点在于可灵活控制冷却空气的液化率，基本不用冷却循环水，流程简单，设备投资少，能耗低等。     

WC/Cu复合材料制备及其高温性能

用机械合金化法结合冷变形，制备了WC／Cu复合材料，研究了冷变形后复合材料的组织特征和高温退火时韵性能变化。结果表明：烧结后的材料经冷变形，组织呈显著纤维状，WC颗粒弥散分布，密度明显提高，达到理论密度的99．2％；复合材料经600～900℃高温退火，强度和硬度略有下降，塑性则有大幅提高；900℃退火时未发生明显的再结晶，界面结合良好；所制备的WC／Cu复合材料有优良的综合性能。     

气调库及气调库设备

分析果蔬贮藏保鲜期的生理变化，介绍气调保鲜库设计施工验收中的技术要求，保鲜工艺和主要设备。